This shop quality pre-set torque driver limits torque applied to fasteners, preventing over-tightening and damage to lightweight components.
The SG-7.2 features two different cutting slots — standard and carbon cutting blade widths — in a hardened steel body with moulded contact points to protect tubes and frames.
These workshop quality tools are made from chrome vanadium steel making them tough and durable so they last a lifetime of use.
Park Tool Oversized Adjustable Saw Guide SG-7.2 Accurately guides a hacksaw to cut aero-shaped seat masts and seat posts up to 2.75"" (70mm), as well as fork steerer tubes and other round tubes from 1-1/16"" to 1-3/4"" (27mm to 45mm). The SG-7.2 features two different cutting slots — standard and carbon cutting blade widths — in a hardened steel body with moulded contact points to protect tubes and frames.Features: The SG-7.2 cutting guide is a specially shaped guide, designed specifically to accept aero-shaped seatmasts and seatposts up to 3.5 inches (89 mm) deep The guide can also accept round tubes from 1-1/4 inch to 1-3/4 inch (32 mm to 45 mm) in diameter Two cutting slots are provided, one for standard saw blades and one for thicker, carbon specific blades Hardened steel body with moulded contact points to protect tubes and frames Made in the USA and covered by Park Tool's legendary limited lifetime warrantyBuy Park Tool Tools from Chain Reaction Cycles, the World's Largest Online Bike Store.
This Park Tool bearing press kit is equipped with one bottom bracket bearing remover and two bushings that will assist with the fitting of new bearings (separately sold headset press tool also required to install pressfit bearing/cups). Ideally suited to removing and replacing BB30, PressFit 30 (PF30), 386EVO, BBright and PF121 systems, this pack will help you to get the job done in no time at all. An up-to-date version of Park Tool's BBT-30.3, this set gives a longer length to work with wider fat bottom bracket shells, making it a fantastic tool to add to any garage or professional bike workshop. How To Use: To remove the bearing, the remover is fed through the shell until the flat head goes into the opposite side bearing. Once engaged, the tool's plastic guide will fit into the near-side shell opening to hold the tool steady while you tap the handle end firmly with a hammer, until the bearing pops out. To install new bearings, the bundled bushings (included) are used with a headset press (not included) to quickly and accurately press the bearings into the shell.
The strength of the Park Tool CN10 comes from its heat-treated and cold-forged steel handles, which feel powerful and dependable in your hand. Its precision ground cutting jaws ensure the smoothest and sharpest cut with every bite, making for that level of quality workmanship that Park Tool wants its users to experience. Providing comfort with quality, the handles are covered by dual-density moulded grips. These are contoured for supreme ergonomic control while you cut your inner or outer cables or crimp your end caps with the tool's built-in crimper. Held tightly together when not in use with its wire handle latch, this is a precise and durable cable cutter that any garage or home workshop should not be without.
The Park Tool FAG2 Frame Alignment Gauge helps solve the problem of many bicycles not shifting or tracking properly. This can be the result of the front and rear wheels not being in line with the frame. If these conditions still exist after wheel and derailleur adjustments, the seat stays, chain stays, and rear drop-outs of the frame may be misaligned. For years the accepted method to check the alignment of the rear drop-out was to run a string on either side. This method does work to some extent. However, it is not accurate because the measurement is not taken at the drop-out. With the Park Tool Frame Alignment Gauge the alignment can be checked quickly and accurately at the drop-out. Retractable pointer to fit all sizes and types of bicycles.
Long and powerful, the 12 inch / 30 cm adjustable spanner is forged from carbon steel for strength and chrome plated for a durable finishA vinyl dipped handle adds comfortJaws open up to 36 mm to allowuse with a whole variety of Park Tool freewheel removers and bottom bracket toolsThe jaws have an accurate laser engraved measurement scale to ensure a good fit every time
Park Tool 12-Inch Adjustable Wrench (PAW-12)An essential tool for your workshop, this 12-Inch Adjustable Wrench from Park Tool is forged from hard-wearing, lightweight carbon steel and is chrome plated for added long-lasting quality. Features:Jaws open to 36mmComfortable vinyl dipped handleFeatures a laser engraved measurement scaleCovered by Park Tool's legendary limited lifetime warrantyBuy Park Tool Workshop Tools from Chain Reaction Cycles, the World's Largest Online Bike Store.
Park Tool Headcup Remover (RT-1)Offering you an efficient and easy way to remove your bike’s pressed in headset cups, the RT-1 just needs a firm impact with your mallet or hammer on its head and the flared ends will accurately extract the cup from the frame. Park Tool has also made this versatile tool compatible with Pressfit 30 (PF30) and SRAM DUB press-fit bottom bracket cups, making it the ideal addition to any professional or home mechanics range of tools.Features:Material: Strong, heat-treated alloy steel with nickel finishCompatibility: Fits 1", 1.1/8" and 1.1/4" headsetsNominal outer diameter of shaft is 1" (25.4mm)For use on 27-38mm (1" to 1.1/2") bearing racesAlso removes PressFit 30 (PF30) bottom bracket units (PressFit 30 inside diameter is the same as headset cups, and are pressed in the same manner)Also easily removes cups on one-piece cranksAlso removes SRAM DUB non-threaded pressed in bottom brackets as well as other PressFit 30 (PF30) systemsFor the 1.1/4 inch and 1.1/2 inch headset standards see the RT-2 model (sold separately)Buy Park Tool Workshop Tools from Chain Reaction Cycles, the World's Largest Online Bike Store.
Covered by Park Tool's legendary limited lifetime warranty
The tool is pulled through the frame until the flared ends snap in behind the cup. A blow on the tool head removes the cup.
Park Tool Threaded T47 Guides for BFS-1The Threaded T47 Guides for BFS-1 from Park Tool are ideal for use as a guide when repairing (facing) damaged threads on your frame threaded bottom bracket shell. This guide is compatible with Park Tool Bottom Bracket Facing Set (BFS-1); Bottom Bracket Tapping & Facing Set (BTS-1) tools and is compatible with Drive Side (left-hand threading) bottom bracket shells.The 648L is a T47 (47mm x 1.0) left-hand threaded standard guide for use when facing bottom bracket shells with the BFS-1 Bottom Bracket Facing Set and 690-XL Oversized Facer. This guide is for use on the drive side (right side) of the bike. This side of the bike drive uses counter-clockwise or left-hand threading.NOTE: For sharpening services of cutting tools see Park Tool Sharpening Services. Always use cutting fluid such as Park Tool CF-2 when machining.Features: Ideal for facing bottom drive side (left hand threading) bracket threads Compatible Park Tool Products: Bottom Bracket Facing Set (BFS-1); Bottom Bracket Tapping & Facing Set (BTS-1)Buy Park Tool Workshop from Chain Reaction Cycles, the World's Largest Online Bike Store.
Park Tool Threaded T47 Guides for BFS-1The Threaded T47 Guides for BFS-1 from Park Tool are ideal for use as a guide when repairing (facing) damaged threads on your frame threaded bottom bracket shell. This guide is compatible with Park Tool Bottom Bracket Facing Set (BFS-1); Bottom Bracket Tapping & Facing Set (BTS-1) tools and is compatible with Drive Side (left-hand threading) bottom bracket shells.The 648L is a T47 (47mm x 1.0) left-hand threaded standard guide for use when facing bottom bracket shells with the BFS-1 Bottom Bracket Facing Set and 690-XL Oversized Facer. This guide is for use on the drive side (right side) of the bike. This side of the bike drive uses counter-clockwise or left-hand threading.NOTE: For sharpening services of cutting tools see Park Tool Sharpening Services. Always use cutting fluid such as Park Tool CF-2 when machining.Features: Ideal for facing bottom drive side (left hand threading) bracket threads Compatible Park Tool Products: Bottom Bracket Facing Set (BFS-1); Bottom Bracket Tapping & Facing Set (BTS-1)Buy Park Tool Workshop from Chain Reaction Cycles, the World's Largest Online Bike Store.
The Park Tool BB press removes and install the bearings and bearing units used in BB86, BB92, Shimano Press Fit, SRAM Press Fit GXP, Race Face Press Fit and other press fit bottom bracket systems using the nominal 24mm spindle. The Park Tool bb tool includes a bearing removal tool, which slides through and expands behind the bearing (like a head cup remover) so it can be tapped out with a hammer. The BBT-90.3 also includes two installation bushings (#669). Use the bushing in conjunction with an HHP-2 or HHP-3 Bearing Cup Press (sold separately) to press the bearings into the frame. Click here to see the user instruction manual for this product
Park Tool Press Fit BB Bearing Tool Set (BBT-90.3)Park Tool has established itself as the go-to brand for professional bike mechanics, and its BBT-90.3 bottom bracket fitting set is the ideal addition to any home or workshop toolbox. Compatible with a wide range of press-fit types, it’s designed to combine with Park Tool’s bearing press tool, to accurately insert or extract the bearing cups into the bike frames bottom bracket shell.Features: Compatibility: BB90, BB92, Shimano press-fit, SRAM press-fit GXP, Race Face press-fit and other press-fit bottom bracket systems Can be used with a Park Tool Bearing Press to press the bearings into the bottom bracket shellBuy Park Tool Workshop from Chain Reaction Cycles, the World's Largest Online Bike Store.
Park Tool Deluxe Threadless Nut Setter TNS-4As a manufacturer of bicycle specific tools since 1963 you can safely rely on Park Tools' many years of experience. The world's largest bike tool manufacturer is the first choice of professional and home bicycle mechanics around the world.Features:The TNS-4 makes it quick and easy to install star-fangled nuts used with 1" and 1-1/8" threadless headset systemsUsing a durable steel driver and built-in guide, the TNS-4 perfectly aligns the star-fangled nut and sets it to the proper depth every time. The unique design virtually eliminates pinched fingersBuy Park Tool Workshop Accessories from Chain Reaction Cycles, the World's Largest Online Bike Store.
The TNS-4 makes it quick and easy to install star-fangled nuts used with 1" and 1-1/8" threadless headset systems
The Park Tool SG6 Saw Guide ensures a straight, clean cut on 1 , 1-1/8 , and 1-1/4 threadless forks. Simply clamp the SG-6 onto the fork and cut, letting the SG-6 guide the hacksaw blade. The SG-6 s non-scratching composite body incorporates steel threads and a steel reinforcing plate to withstand the rigors of heavy shop use.
Park Tool Frame Alignment Gauge (FAG-2) The Frame Alignment Gauge FAG-2 from Park Tool is a specifically designed device for accurate measurement of your frame's positioning, taking its reading with precision, direct from the drop out.Quick and Easy Alignment Measurement When your frame is off kilter with your wheels, shifting and tracking can often be impacted, lowering you and your bike's performance. Even after adjusting wheels and derailleurs, your frame may still not be in the right position. With the Frame Alignment Gauge FAG-2, you can quickly and accurately see exactly what realignment is required to straighten out the issue. Suitable for use on all types of bikes, the FAG-2 has a retractable pointer for making sure alignment is properly achieved on any size of bicycle. Features: Retractable pointer for use on all sizes and types of bike Accurate and precise alignment measurement, direct from the drop out Buy Park Tool Workshop from Chain Reaction Cycles, the World's Largest Online Bike Store.