Peaty's unique single-sided fork design allows for multiple plug sizes to be easily rolled into the dip of the fork and pushed straight into the tyre. The open side to the fork then allows for the tool to be easily pulled back out of the hole without pulling the plug out with it.Available in 12x Chris King coloursQuick and easy to insert tyre plugs. With our unique single-sided fork design, you simply push and roll the plug into the hook of the forkWith no tight gap to squeeze through, the plug is far less likely to pull back out when the tool is extracted the fork is sharp tipped & as slim as possible, so it doesn't widen the size of the - hole already thereFork made from 316 stainless steelBody made from anodised 6061 aluminiumKnurled body and ribbed lid / handle for extra gripWeather sealing O-rings make the tool waterproof when assembledEach kit comes with one sheet of 3x 1.5mm and one sheet of 3x 3mm plugsMade from high quality 316 Stainless steel, the fork is designed to be as short as possible to reduce the chance of you puncturing your rim tape when inserting a plug. The fork has also been designed with a reaming texture on the shaft, to clean out punctures before plugging, and to be as slim as possible, so it doesn't widen the size of the hole already there.Shrinking down to a tiny 65mm x 19mm, this tool has been designed to easily fit into your pocket or slot into a tool wrap or backpack. With knurling on the tool base and ribbing on the lid, you shouldn't have any issues gripping the tool, even in the muddiest of conditions.Simply unscrew the lid and thread it onto the rear of the tool to make a sturdy handle to hold onto while inserting the plug. This pack includes three thick (3mm) plugs and three thin (1.5mm) plugs. These plug sheets can be neatly wrapped around the fork and stored neatly inside the compact water-sealed body. Holeshot refill plug sheets also sold separately packaged with cardboard header cards & in biodegradable bags.
Born in the lab and raised between the tapes, Peaty's Link Lube is a minty fresh, triple distilled, ultra high speed chain oil for use in all conditions.Unique formula with two-parts cleans and lubes your chainSecret sauce provides long lasting protection in all conditionsClear base is anti-corrosive and water displacing to help make your chain last longerThe unique two-part formula penetrates and cleans deep inside your chain, driving out moisture, grit and grime and replacing them with unique blend of oils and waxes (Peaty's secret sauce) to lubricate and protect. Yes, you read that correctly... Peaty's Link Lube actually cleans your chain as you use it! LinkLube features a mystery blue secret sauce which enables the lube to be used in all weather conditions.The secret sauce is a unique compound of oils and waxes which are usually only found individually in either wet or dry lubes. This provides incredible long-lasting protection in the wet, while remaining clean in dry and dusty conditions. The clear base lube is an anti-corrosive, fast penetrating, water displacing oil which will find its way into every nook and cranny of your chain. Once it reaches the inner depths of your chain links, the base oil will drive out moisture, grit and grime and leave behind the special sauce to reduce friction, reduce vibration and reduce drivetrain noise.
This thin, single core cylindrical brush is the perfect small-space detailing partner to our beasty bog brush. Designed to get into those small hard-to-clean gaps like suspension linkages, pedals, fork braces, seat rails, hubs and in between spokes. The stiff wire core is coated to prevent damage while the thick, super-soft cotton tip also prevents the end of the wire core from scratching paint.Thin cylindrical shaped for hard to reach areasCrimped medium density bristles made from post-consumer recycled materialUnique soft cotton tip to prevent scratchingPlastic coated wire core also helps prevent scratchingIdeal for use on suspension linkages, pedals, seat rails, hubs and spokesMade from waxed beech woodLaser etched Peaty's logo on the handle
Peaty s Tubeless Conversion Kit includes everything you need to run a fully optimised tubeless setup Peaty s Rim Tape, MK2 Tubeless Valves and Holeshot Sealant. If you value more time spent on the bike and less time fixing punctures, this is the perfect set up.Includes Peaty's latest silver-printed Tubeless Rim TapeBlack MK2 Tubeless Valves and Holeshot Biofibre Tubeless SealantPresented in specially-designed recycled packaging with a handy setup guide on the box and QR links to step by step videos for each stage of installationIdeal for riders wanting to spend more time on the bike and less time fixing puncturesPeaty's Tubeless Conversion kits are beautifully laid out with easy to follow setup instructions. These conversion kits are available in a variety of configurations so that you can ride with the perfect tubeless set up whatever your discipline: Road, Gravel, XC, Enduro, Downhill all good to go. Every conversion kit features a handy installation guide on the box, with QR links to step by step installation for each stage of installation rest assured that the installation process will be slick and swift.Available in 4 flavours:Road/Gravel: 21mm tape / 60mm valves / 120ml SealantXC/Trail: 25mm tape / 42mm valves / 240ml SealantDH/Enduro: 30mm tape / 42mm valves / 240ml SealantDH Wide: 35mm tape / 42mm valves / 240ml Sealant
Peaty s Tubeless Conversion Kit includes everything you need to run a fully optimised tubeless setup Peaty s Rim Tape, MK2 Tubeless Valves and Holeshot Sealant. If you value more time spent on the bike and less time fixing punctures, this is the perfect set up.Includes Peaty's latest silver-printed Tubeless Rim TapeBlack MK2 Tubeless Valves and Holeshot Biofibre Tubeless SealantPresented in specially-designed recycled packaging with a handy setup guide on the box and QR links to step by step videos for each stage of installationIdeal for riders wanting to spend more time on the bike and less time fixing puncturesPeaty's Tubeless Conversion kits are beautifully laid out with easy to follow setup instructions. These conversion kits are available in a variety of configurations so that you can ride with the perfect tubeless set up whatever your discipline: Road, Gravel, XC, Enduro, Downhill all good to go. Every conversion kit features a handy installation guide on the box, with QR links to step by step installation for each stage of installation rest assured that the installation process will be slick and swift.Available in 4 flavours:Road/Gravel: 21mm tape / 60mm valves / 120ml SealantXC/Trail: 25mm tape / 42mm valves / 240ml SealantDH/Enduro: 30mm tape / 42mm valves / 240ml SealantDH Wide: 35mm tape / 42mm valves / 240ml Sealant
Peaty s Tubeless Conversion Kit includes everything you need to run a fully optimised tubeless setup Peaty s Rim Tape, MK2 Tubeless Valves and Holeshot Sealant. If you value more time spent on the bike and less time fixing punctures, this is the perfect set up.Includes Peaty's latest silver-printed Tubeless Rim TapeBlack MK2 Tubeless Valves and Holeshot Biofibre Tubeless SealantPresented in specially-designed recycled packaging with a handy setup guide on the box and QR links to step by step videos for each stage of installationIdeal for riders wanting to spend more time on the bike and less time fixing puncturesPeaty's Tubeless Conversion kits are beautifully laid out with easy to follow setup instructions. These conversion kits are available in a variety of configurations so that you can ride with the perfect tubeless set up whatever your discipline: Road, Gravel, XC, Enduro, Downhill all good to go. Every conversion kit features a handy installation guide on the box, with QR links to step by step installation for each stage of installation rest assured that the installation process will be slick and swift.Available in 4 flavours:Road/Gravel: 21mm tape / 60mm valves / 120ml SealantXC/Trail: 25mm tape / 42mm valves / 240ml SealantDH/Enduro: 30mm tape / 42mm valves / 240ml SealantDH Wide: 35mm tape / 42mm valves / 240ml Sealant
Peaty s Tubeless Conversion Kit includes everything you need to run a fully optimised tubeless setup Peaty s Rim Tape, MK2 Tubeless Valves and Holeshot Sealant. If you value more time spent on the bike and less time fixing punctures, this is the perfect set up.Includes Peaty's latest silver-printed Tubeless Rim TapeBlack MK2 Tubeless Valves and Holeshot Biofibre Tubeless SealantPresented in specially-designed recycled packaging with a handy setup guide on the box and QR links to step by step videos for each stage of installationIdeal for riders wanting to spend more time on the bike and less time fixing puncturesPeaty's Tubeless Conversion kits are beautifully laid out with easy to follow setup instructions. These conversion kits are available in a variety of configurations so that you can ride with the perfect tubeless set up whatever your discipline: Road, Gravel, XC, Enduro, Downhill all good to go. Every conversion kit features a handy installation guide on the box, with QR links to step by step installation for each stage of installation rest assured that the installation process will be slick and swift.Available in 4 flavours:Road/Gravel: 21mm tape / 60mm valves / 120ml SealantXC/Trail: 25mm tape / 42mm valves / 240ml SealantDH/Enduro: 30mm tape / 42mm valves / 240ml SealantDH Wide: 35mm tape / 42mm valves / 240ml Sealant
Developed alongside World Cup mechanics and world champion racers. Peaty's Holeshot Tubeless Sealant is packed full of biodegradable fibres & sealing particles to give a fast and strong seal. Using the latest fast-acting latex, our water-based sealant is ammonia-free, non-hazardous and lasts up to 6 months in the tyre in temperate climates*. It won't ball up in the tyre and is easily washed out. Our biodegradable fibres and particles bind together with the fast-acting latex to create a clot (like platelets in your blood) to quickly & effectively seal holes and tears up to 6mm.Biodegradable sealing fibresBiodegradable plateletsCO2 compatibleSeals up to 6mm holesOperating pressures: 15 to 120 psiOperating temperature: -20°c to +50°cSeals porous tyres and bead/rim gaps setup
Developed alongside World Cup mechanics and world champion racers. Peaty's Holeshot Tubeless Sealant is packed full of biodegradable fibres & sealing particles to give a fast and strong seal. Using the latest fast-acting latex, our water-based sealant is ammonia-free, non-hazardous and lasts up to 6 months in the tyre in temperate climates*. It won't ball up in the tyre and is easily washed out. Our biodegradable fibres and particles bind together with the fast-acting latex to create a clot (like platelets in your blood) to quickly & effectively seal holes and tears up to 6mm.Biodegradable sealing fibresBiodegradable plateletsCO2 compatibleSeals up to 6mm holesOperating pressures: 15 to 120 psiOperating temperature: -20°c to +50°cSeals porous tyres and bead/rim gaps setup
Designed in conjunction with Chris King, Peaty's MK2 Tubeless Valves are made from premium lightweight, high strength 7075 aluminium, and fit most tubeless setups from MTB to road and cyclocross, including carbon, enduro and DH rims.Lightweight & durable 7050 aluminium constructionColoured to match Chris King componentsSlotted base compatible with or without tyre insertsValve caps double as 3.4mm spoke key and valve core removal toolThe unique x-cut base has been designed to work with all tyre inserts. The channels cut into the base of the valve allow air and sealant to pass through when inserts are pushed up against them. Unlike most other insert-compatible valves, the MK2 valves have a straight-through design so there's no reduction of sealant or air flow when tyre inserts are not used.Fitting couldn't be easier. integrated o-rings prevent the lock rings from scratching your precious rims and large soft rubber bases easily create an airtight seal. Designed by riders, for riders. Our valves come as standard with an integrated valve core remover cap and spoke key cap (for standard 3.4mm spoke nipples). This makes tightening loose spokes and topping up with sealant a breeze, either in the workshop or out on the trails.
Everyone knows that a straight line is the fastest line! That's why Peaty's made their Holeshot CO2 tyre inflator straight, rather than bent at 90 degrees. This straight line design enables faster airflow for rapid inflation and creates less stress on your tubeless valves when you're using it because you're coming at the valve straight on rather than at a 90 degree angle.Available in 12x Chris King coloursUnique Patent Pending compact straight line design for maximum airflowSimply push down to inflateUnique closed base silicone Freeze protector sleeve prevents your hands from freezing, even without glovesEach kit contains 1x inflator head, 2x CO2 cartridges and 1x freeze protector sleeveIt's as small and lightweight as possible, so it's easy to carry in your pocket, bag or strapped to your bike. Made from CNC'd 6061 aluminium, and with a patent pending valve design, the details of Peaty's inflator heads have been agonised on - from the exact rubber compound of the O-rings to the awesome Chris king anodized colours.Not stopping at the inflator head, Peaty's applied the same level of detail and quality in making a high quality CO2 cartridge sleeve. far from a cheap strip of neoprene, our freeze protector sleeve is made from temperature resistant silicone and has a unique closed base to stop your hand from freezing to the cartridge, no matter how you hold it - even without wearing gloves.
Designed in conjunction with Chris King, Peaty's MK2 Tubeless Valves are made from premium lightweight, high strength 7075 aluminium, and fit most tubeless setups from MTB to road and cyclocross, including carbon, enduro and DH rims.Lightweight & durable 7050 aluminium constructionColoured to match Chris King componentsSlotted base compatible with or without tyre insertsValve caps double as 3.4mm spoke key and valve core removal toolThe unique x-cut base has been designed to work with all tyre inserts. The channels cut into the base of the valve allow air and sealant to pass through when inserts are pushed up against them. Unlike most other insert-compatible valves, the MK2 valves have a straight-through design so there's no reduction of sealant or air flow when tyre inserts are not used.Fitting couldn't be easier. integrated o-rings prevent the lock rings from scratching your precious rims and large soft rubber bases easily create an airtight seal. Designed by riders, for riders. Our valves come as standard with an integrated valve core remover cap and spoke key cap (for standard 3.4mm spoke nipples). This makes tightening loose spokes and topping up with sealant a breeze, either in the workshop or out on the trails.
Developed alongside World Cup mechanics and world champion racers. Peaty's Holeshot Tubeless Sealant is packed full of biodegradable fibres & sealing particles to give a fast and strong seal. Using the latest fast-acting latex, our water-based sealant is ammonia-free, non-hazardous and lasts up to 6 months in the tyre in temperate climates*. It won't ball up in the tyre and is easily washed out. Our biodegradable fibres and particles bind together with the fast-acting latex to create a clot (like platelets in your blood) to quickly & effectively seal holes and tears up to 6mm.Biodegradable sealing fibresBiodegradable plateletsCO2 compatibleSeals up to 6mm holesOperating pressures: 15 to 120 psiOperating temperature: -20°c to +50°cSeals porous tyres and bead/rim gaps setup
Peaty's Suspension Assembly Grease is a lithium-free grease specifically developed for use in suspension forks, rear shocks and dropper seatposts.For suspension forks, rear shocks & dropper postsControlled shear thinning for consistent plush performanceNon-migratory so stays where you put it!Biodegradable100% PCR & PIR Recycled PackagingM15 threaded capMoving parts create friction. This causes most greases to change in viscosity (known as shear thinning), which can rapidly change the feel & performance of your suspension. Our grease has been designed to have a controlled level of shear thinning which means your suspension will feel consistently plush throughout your ride or race run. This then also makes it non-migratory which means it stays where you put it! Non-toxic, transparent, clean-running and highly resistant to water washout, our grease has added corrosion inhibitors and is compatible with all elastomers, O-rings, seals and oil baths.
Peaty s speed grease runs 2.5 times longer than our assembly grease, whilst still providing long-lasting performance under extreme pressures. Perfect for use in race hubs, bottom brackets and other fast-moving parts.For use in race wheel bearings bottom brackets and fast moving partsAnti-corrosion protectionLong-lasting lubrication under extreme loadsAnti-corrosion protectionHigh resistance to water washoutCarbon safe100% recycled packagingSize: 100g
Born from the professional World Cup Mountain biking circuit and designed specifically for use on high-tech bikes and their components. Peaty's LoamFoam is a minty fresh, professional-grade, biodegradable cleaner that is tough on dirt yet safe to use on all bike surfaces including carbon, brake pads and discs.LoamFoam's unique cleaning formulation is blended with organic gelling agents, allowing the active cleaning compounds to cling to your bike for longer. The result is a shiny clean steed with minimal effort. Simply apply Peaty's LoamFoam liberally to dirty surfaces, wait for 3 - 5 minutes and blast off with clean water. Stubborn dried-on dirt may need to be persuaded with a soft bristled brush then rinsed off with cold water. It's that easy with Peaty's LoamFoam Cleaner!
Everyone knows that a straight line is the fastest line! That's why Peaty's made their Holeshot CO2 tyre inflator straight, rather than bent at 90 degrees. This straight line design enables faster airflow for rapid inflation and creates less stress on your tubeless valves when you're using it because you're coming at the valve straight on rather than at a 90 degree angle.Available in 12x Chris King coloursUnique Patent Pending compact straight line design for maximum airflowSimply push down to inflateUnique closed base silicone Freeze protector sleeve prevents your hands from freezing, even without glovesEach kit contains 1x inflator head, 2x CO2 cartridges and 1x freeze protector sleeveIt's as small and lightweight as possible, so it's easy to carry in your pocket, bag or strapped to your bikeMade from CNC'd 6061 aluminium, and with a patent pending valve design, the details of Peaty's inflator heads have been agonised on - from the exact rubber compound of the O-rings to the awesome Chris King anodized colours. Not stopping at the inflator head, Peaty's applied the same level of detail and quality in making a high quality CO2 cartridge sleeve. far from a cheap strip of neoprene, our freeze protector sleeve is made from temperature resistant silicone and has a unique closed base to stop your hand from freezing to the cartridge, no matter how you hold it - even without wearing gloves.
Designed in conjunction with Chris King, Peaty's MK2 Tubeless Valves are made from premium lightweight, high strength 7075 aluminium, and fit most tubeless setups from MTB to road and cyclocross, including carbon, enduro and DH rims.Lightweight & durable 7050 aluminium constructionColoured to match Chris King componentsSlotted base compatible with or without tyre insertsValve caps double as 3.4mm spoke key and valve core removal toolThe unique x-cut base has been designed to work with all tyre inserts. The channels cut into the base of the valve allow air and sealant to pass through when inserts are pushed up against them. Unlike most other insert-compatible valves, the MK2 valves have a straight-through design so there's no reduction of sealant or air flow when tyre inserts are not used.Fitting couldn't be easier. integrated o-rings prevent the lock rings from scratching your precious rims and large soft rubber bases easily create an airtight seal. Designed by riders, for riders. Our valves come as standard with an integrated valve core remover cap and spoke key cap (for standard 3.4mm spoke nipples). This makes tightening loose spokes and topping up with sealant a breeze, either in the workshop or out on the trails.
Designed in conjunction with Chris King, Peaty's MK2 Tubeless Valves are made from premium lightweight, high strength 7075 aluminium, and fit most tubeless setups from MTB to road and cyclocross, including carbon, enduro and DH rims.Lightweight & durable 7050 aluminium constructionColoured to match Chris King componentsSlotted base compatible with or without tyre insertsValve caps double as 3.4mm spoke key and valve core removal toolThe unique x-cut base has been designed to work with all tyre inserts. The channels cut into the base of the valve allow air and sealant to pass through when inserts are pushed up against them. Unlike most other insert-compatible valves, the MK2 valves have a straight-through design so there's no reduction of sealant or air flow when tyre inserts are not used.Fitting couldn't be easier. integrated o-rings prevent the lock rings from scratching your precious rims and large soft rubber bases easily create an airtight seal. Designed by riders, for riders. Our valves come as standard with an integrated valve core remover cap and spoke key cap (for standard 3.4mm spoke nipples). This makes tightening loose spokes and topping up with sealant a breeze, either in the workshop or out on the trails.
Peaty's Disc Brake Cleaner is a unique, rapidly spraying blend of fast-drying solvents designed to blast away contaminants such as dust, greases, and oils from braking components. Designed to improve braking performance and re-condition tired brake pads. Improves braking performanceDissolves greases and oilsRe-conditions brake padsReduces brake squealCarbon safeReadily biodegradable formula400ml of product in a compact canColour coded ring for easy worktop identificationFor use on all functional components in brake assemblies, including callipers, discs and pads. It's also readily biodegradable too so you don't have to unnecessarily damage the environment to have banging brake performance! Peaty s designed their 400ml can so it s short and girthy to fit easier into your toolbox, while the coloured identifier rings help you quickly find the can you want amongst the stack of aerosol cans you already have.