Peaty's unique single-sided fork design allows for multiple plug sizes to be easily rolled into the dip of the fork and pushed straight into the tyre. The open side to the fork then allows for the tool to be easily pulled back out of the hole without pulling the plug out with it.Available in 12x Chris King coloursQuick and easy to insert tyre plugs. With our unique single-sided fork design, you simply push and roll the plug into the hook of the forkWith no tight gap to squeeze through, the plug is far less likely to pull back out when the tool is extracted the fork is sharp tipped & as slim as possible, so it doesn't widen the size of the - hole already thereFork made from 316 stainless steelBody made from anodised 6061 aluminiumKnurled body and ribbed lid / handle for extra gripWeather sealing O-rings make the tool waterproof when assembledEach kit comes with one sheet of 3x 1.5mm and one sheet of 3x 3mm plugsMade from high quality 316 Stainless steel, the fork is designed to be as short as possible to reduce the chance of you puncturing your rim tape when inserting a plug. The fork has also been designed with a reaming texture on the shaft, to clean out punctures before plugging, and to be as slim as possible, so it doesn't widen the size of the hole already there.Shrinking down to a tiny 65mm x 19mm, this tool has been designed to easily fit into your pocket or slot into a tool wrap or backpack. With knurling on the tool base and ribbing on the lid, you shouldn't have any issues gripping the tool, even in the muddiest of conditions.Simply unscrew the lid and thread it onto the rear of the tool to make a sturdy handle to hold onto while inserting the plug. This pack includes three thick (3mm) plugs and three thin (1.5mm) plugs. These plug sheets can be neatly wrapped around the fork and stored neatly inside the compact water-sealed body. Holeshot refill plug sheets also sold separately packaged with cardboard header cards & in biodegradable bags.
Peaty's unique single-sided fork design allows for multiple plug sizes to be easily rolled into the dip of the fork and pushed straight into the tyre. The open side to the fork then allows for the tool to be easily pulled back out of the hole without pulling the plug out with it.Available in 12x Chris King coloursQuick and easy to insert tyre plugs. With our unique single-sided fork design, you simply push and roll the plug into the hook of the forkWith no tight gap to squeeze through, the plug is far less likely to pull back out when the tool is extracted the fork is sharp tipped & as slim as possible, so it doesn't widen the size of the - hole already thereFork made from 316 stainless steelBody made from anodised 6061 aluminiumKnurled body and ribbed lid / handle for extra gripWeather sealing O-rings make the tool waterproof when assembledEach kit comes with one sheet of 3x 1.5mm and one sheet of 3x 3mm plugsMade from high quality 316 Stainless steel, the fork is designed to be as short as possible to reduce the chance of you puncturing your rim tape when inserting a plug. The fork has also been designed with a reaming texture on the shaft, to clean out punctures before plugging, and to be as slim as possible, so it doesn't widen the size of the hole already there.Shrinking down to a tiny 65mm x 19mm, this tool has been designed to easily fit into your pocket or slot into a tool wrap or backpack. With knurling on the tool base and ribbing on the lid, you shouldn't have any issues gripping the tool, even in the muddiest of conditions.Simply unscrew the lid and thread it onto the rear of the tool to make a sturdy handle to hold onto while inserting the plug. This pack includes three thick (3mm) plugs and three thin (1.5mm) plugs. These plug sheets can be neatly wrapped around the fork and stored neatly inside the compact water-sealed body. Holeshot refill plug sheets also sold separately packaged with cardboard header cards & in biodegradable bags.
Designed by pro riders, mechanics and scientists, Peaty's Rim Job has been developed from the ground up as a bicycle rim tape. The super high tensile strength tape is primed with a bespoke adhesive which clings like proverbial to a blanket, yet leaves a minimal mess when removed. An optimum amount of stretch and large rigid recyclable core allows the tape to be pulled and applied with tension, contouring your rim tightly for a better fit. Do you struggle to find the hole No problem! Just hold your rim up to the light and the tape's semi-transparent finish will illuminate the way. One 9 meter roll will cover approximately: 5 x 26" Rims, 4 x 27.5" Rims, 4 x 29" Rims or 4 x 700c Rims.
Designed by pro riders, mechanics and scientists, Peaty's Rim Job has been developed from the ground up as a bicycle rim tape. The super high tensile strength tape is primed with a bespoke adhesive which clings like proverbial to a blanket, yet leaves a minimal mess when removed. An optimum amount of stretch and large rigid recyclable core allows the tape to be pulled and applied with tension, contouring your rim tightly for a better fit. Do you struggle to find the hole No problem! Just hold your rim up to the light and the tape's semi-transparent finish will illuminate the way. One 9 meter roll will cover approximately: 5 x 26" Rims, 4 x 27.5" Rims, 4 x 29" Rims or 4 x 700c Rims.
Designed in conjunction with Chris King, Peaty's MK2 Tubeless Valves are made from premium lightweight, high strength 7075 aluminium, and fit most tubeless setups from MTB to road and cyclocross, including carbon, enduro and DH rims.Lightweight & durable 7050 aluminium constructionColoured to match Chris King componentsSlotted base compatible with or without tyre insertsValve caps double as 3.4mm spoke key and valve core removal toolThe unique x-cut base has been designed to work with all tyre inserts. The channels cut into the base of the valve allow air and sealant to pass through when inserts are pushed up against them. Unlike most other insert-compatible valves, the MK2 valves have a straight-through design so there's no reduction of sealant or air flow when tyre inserts are not used.Fitting couldn't be easier. integrated o-rings prevent the lock rings from scratching your precious rims and large soft rubber bases easily create an airtight seal. Designed by riders, for riders. Our valves come as standard with an integrated valve core remover cap and spoke key cap (for standard 3.4mm spoke nipples). This makes tightening loose spokes and topping up with sealant a breeze, either in the workshop or out on the trails.
Designed in conjunction with Chris King, Peaty's MK2 Tubeless Valves are made from premium lightweight, high strength 7075 aluminium, and fit most tubeless setups from MTB to road and cyclocross, including carbon, enduro and DH rims.Lightweight & durable 7050 aluminium constructionColoured to match Chris King componentsSlotted base compatible with or without tyre insertsValve caps double as 3.4mm spoke key and valve core removal toolThe unique x-cut base has been designed to work with all tyre inserts. The channels cut into the base of the valve allow air and sealant to pass through when inserts are pushed up against them. Unlike most other insert-compatible valves, the MK2 valves have a straight-through design so there's no reduction of sealant or air flow when tyre inserts are not used.Fitting couldn't be easier. integrated o-rings prevent the lock rings from scratching your precious rims and large soft rubber bases easily create an airtight seal. Designed by riders, for riders. Our valves come as standard with an integrated valve core remover cap and spoke key cap (for standard 3.4mm spoke nipples). This makes tightening loose spokes and topping up with sealant a breeze, either in the workshop or out on the trails.
Designed in conjunction with Chris King, Peaty's MK2 Tubeless Valves are made from premium lightweight, high strength 7075 aluminium, and fit most tubeless setups from MTB to road and cyclocross, including carbon, enduro and DH rims.Lightweight & durable 7050 aluminium constructionColoured to match Chris King componentsSlotted base compatible with or without tyre insertsValve caps double as 3.4mm spoke key and valve core removal toolThe unique x-cut base has been designed to work with all tyre inserts. The channels cut into the base of the valve allow air and sealant to pass through when inserts are pushed up against them. Unlike most other insert-compatible valves, the MK2 valves have a straight-through design so there's no reduction of sealant or air flow when tyre inserts are not used.Fitting couldn't be easier. integrated o-rings prevent the lock rings from scratching your precious rims and large soft rubber bases easily create an airtight seal. Designed by riders, for riders. Our valves come as standard with an integrated valve core remover cap and spoke key cap (for standard 3.4mm spoke nipples). This makes tightening loose spokes and topping up with sealant a breeze, either in the workshop or out on the trails.
Designed in conjunction with Chris King, Peaty's MK2 Tubeless Valves are made from premium lightweight, high strength 7075 aluminium, and fit most tubeless setups from MTB to road and cyclocross, including carbon, enduro and DH rims.Lightweight & durable 7050 aluminium constructionColoured to match Chris King componentsSlotted base compatible with or without tyre insertsValve caps double as 3.4mm spoke key and valve core removal toolThe unique x-cut base has been designed to work with all tyre inserts. The channels cut into the base of the valve allow air and sealant to pass through when inserts are pushed up against them. Unlike most other insert-compatible valves, the MK2 valves have a straight-through design so there's no reduction of sealant or air flow when tyre inserts are not used.Fitting couldn't be easier. integrated o-rings prevent the lock rings from scratching your precious rims and large soft rubber bases easily create an airtight seal. Designed by riders, for riders. Our valves come as standard with an integrated valve core remover cap and spoke key cap (for standard 3.4mm spoke nipples). This makes tightening loose spokes and topping up with sealant a breeze, either in the workshop or out on the trails.
Designed in conjunction with Chris King, Peaty's MK2 Tubeless Valves are made from premium lightweight, high strength 7075 aluminium, and fit most tubeless setups from MTB to road and cyclocross, including carbon, enduro and DH rims.Lightweight & durable 7050 aluminium constructionColoured to match Chris King componentsSlotted base compatible with or without tyre insertsValve caps double as 3.4mm spoke key and valve core removal toolThe unique x-cut base has been designed to work with all tyre inserts. The channels cut into the base of the valve allow air and sealant to pass through when inserts are pushed up against them. Unlike most other insert-compatible valves, the MK2 valves have a straight-through design so there's no reduction of sealant or air flow when tyre inserts are not used.Fitting couldn't be easier. integrated o-rings prevent the lock rings from scratching your precious rims and large soft rubber bases easily create an airtight seal. Designed by riders, for riders. Our valves come as standard with an integrated valve core remover cap and spoke key cap (for standard 3.4mm spoke nipples). This makes tightening loose spokes and topping up with sealant a breeze, either in the workshop or out on the trails.
Designed in conjunction with Chris King, Peaty's MK2 Tubeless Valves are made from premium lightweight, high strength 7075 aluminium, and fit most tubeless setups from MTB to road and cyclocross, including carbon, enduro and DH rims.Lightweight & durable 7050 aluminium constructionColoured to match Chris King componentsSlotted base compatible with or without tyre insertsValve caps double as 3.4mm spoke key and valve core removal toolThe unique x-cut base has been designed to work with all tyre inserts. The channels cut into the base of the valve allow air and sealant to pass through when inserts are pushed up against them. Unlike most other insert-compatible valves, the MK2 valves have a straight-through design so there's no reduction of sealant or air flow when tyre inserts are not used.Fitting couldn't be easier. integrated o-rings prevent the lock rings from scratching your precious rims and large soft rubber bases easily create an airtight seal. Designed by riders, for riders. Our valves come as standard with an integrated valve core remover cap and spoke key cap (for standard 3.4mm spoke nipples). This makes tightening loose spokes and topping up with sealant a breeze, either in the workshop or out on the trails.
Designed in conjunction with Chris King, Peaty's MK2 Tubeless Valves are made from premium lightweight, high strength 7075 aluminium, and fit most tubeless setups from MTB to road and cyclocross, including carbon, enduro and DH rims.Lightweight & durable 7050 aluminium constructionColoured to match Chris King componentsSlotted base compatible with or without tyre insertsValve caps double as 3.4mm spoke key and valve core removal toolThe unique x-cut base has been designed to work with all tyre inserts. The channels cut into the base of the valve allow air and sealant to pass through when inserts are pushed up against them. Unlike most other insert-compatible valves, the MK2 valves have a straight-through design so there's no reduction of sealant or air flow when tyre inserts are not used.Fitting couldn't be easier. integrated o-rings prevent the lock rings from scratching your precious rims and large soft rubber bases easily create an airtight seal. Designed by riders, for riders. Our valves come as standard with an integrated valve core remover cap and spoke key cap (for standard 3.4mm spoke nipples). This makes tightening loose spokes and topping up with sealant a breeze, either in the workshop or out on the trails.
Designed in conjunction with Chris King, Peaty's MK2 Tubeless Valves are made from premium lightweight, high strength 7075 aluminium, and fit most tubeless setups from MTB to road and cyclocross, including carbon, enduro and DH rims.Lightweight & durable 7050 aluminium constructionColoured to match Chris King componentsSlotted base compatible with or without tyre insertsValve caps double as 3.4mm spoke key and valve core removal toolThe unique x-cut base has been designed to work with all tyre inserts. The channels cut into the base of the valve allow air and sealant to pass through when inserts are pushed up against them. Unlike most other insert-compatible valves, the MK2 valves have a straight-through design so there's no reduction of sealant or air flow when tyre inserts are not used.Fitting couldn't be easier. integrated o-rings prevent the lock rings from scratching your precious rims and large soft rubber bases easily create an airtight seal. Designed by riders, for riders. Our valves come as standard with an integrated valve core remover cap and spoke key cap (for standard 3.4mm spoke nipples). This makes tightening loose spokes and topping up with sealant a breeze, either in the workshop or out on the trails.