Nukeproof Tubeless MTB Rim Tape (10m)This durable and dependable Nukeproof tubeless tape has been tested by its in-house team and athletes to ensure a firm and effective seal. Made to meet the demands of downhill and enduro racing, it does a sterling job in keeping your tubes protected as you take on the most daring descents and trails. One 10-metre roll will be enough tape to cater for 4x 29” wheels. One layer with a 4” overlap is all that is required to tape your wheel for tubeless setup. We recommend using a tape which is 2 - 3mm wider than your inner rim width Instructions for Use Remove any old tape and sealant residue Ensure rim is clean and dry Start opposite the valve hole and maintain tension as you apply tape Work air bubbles out as you tape the wheel (Push them out via the spoke holes) Apply one layer of tape with a 4" overlap Ensure all air bubbles have been removed and tape is fully stuck right out to the edges of the rim Pierce a small hole and insert your valveFeatures: Length: 10m Suitability: Downhill, Enduro Buy Nukeproof Wheels & Tyres from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Tubeless MTB Rim Tape (10m)This durable and dependable Nukeproof tubeless tape has been tested by its in-house team and athletes to ensure a firm and effective seal. Made to meet the demands of downhill and enduro racing, it does a sterling job in keeping your tubes protected as you take on the most daring descents and trails. One 10-metre roll will be enough tape to cater for 4x 29” wheels. One layer with a 4” overlap is all that is required to tape your wheel for tubeless setup. We recommend using a tape which is 2 - 3mm wider than your inner rim width Instructions for Use Remove any old tape and sealant residue Ensure rim is clean and dry Start opposite the valve hole and maintain tension as you apply tape Work air bubbles out as you tape the wheel (Push them out via the spoke holes) Apply one layer of tape with a 4" overlap Ensure all air bubbles have been removed and tape is fully stuck right out to the edges of the rim Pierce a small hole and insert your valveFeatures: Length: 10m Suitability: Downhill, Enduro Buy Nukeproof Wheels & Tyres from Chain Reaction Cycles, the World's Largest Online Bike Store.
This is a genuine Nukeproof replacement cable guide kit for the Nukeproof Megawatt with downtube cable entry. Not suitable for models with headset cable entry.
Engineered specifically for the 2020 Nukeproof Dissent, this genuine Nukeproof protector provides an exceptional barrier against mud, muck and riding mishaps thanks to their durable moulded silicone construction. It attaches to your frame's downtube via its 3M adhesive backing and offers outstanding protection against all types of dirt and damage.
A genuine Nukeproof headtube badge, it's compatible with Mega, Snap and Scalp.
Nukeproof's Megawatt Mid Protector is placed between the Battery Door Protector and Motor Protector, it will help protect this portion of the frame from damage out on the trail. Attaching to your frame via the 3M adhesive backing, the Megawatt Mid Protector is the ideal barrier against bangs, dings and dirt. The MID Protector is part D in the exploded diagram here.
This high-quality Nukeproof Mega 275 Carbon Downtube Protector is ideal for keeping your downtube in pristine condition from stones and dirt as you rip through the trails. Ideal for keeping your bike protected against harsh elements on a regular basis, this downtube protector is a great shield against all dirt that the rough terrain throws at you. Specially designed to fit 2018 Mega Carbon 275 models, this genuine Nukeproof protector is made from robust silicone construction. Easy to install to your downtube thanks to the 3M adhesive backing, the Mega Carbon - Downtube Protector is the perfect addition to your bike for maximum protection ride after ride.
Specially designed for current 2016-2018 Nukeproof Mega Alloy 275 and 290 models, the Mega Alloy - Downtube Protector is perfect for keeping your bikes framework free from damage. Made from moulded silicone construction for years of long-lasting protection against mud and dirt. Keep your downtube in peak condition from scratches, scores and scrapes thanks to this easy to apply shield. After a long day out on the trails, you can only expect stone rebounds and dirt backlash from riding the trails, so the Mega Alloy - Downtube Protector will give you a strong and durable solution for defending against all that the elements throw at you. Easy to apply thanks to the 3M adhesive backing, you can effortlessly install this helpful tool to protect your bike ride after ride. The Mega Alloy - Downtube Protector from Nukeproof is the perfect choice to keep your bikes framework safe from mud and dirt in even the most extreme conditions, all year round.
A.R.D uses closed cell foam’s technology to make a lightweight tyre insert which gives you a lot of protection. A.R.D will enable you to run lower pressures without getting flats and in turn assist you to increase your grip out on the trails. Keeping weight down was a key factor in the development of ARD, a 27.5” insert will weigh 130g. Rider Kelan Grant has been using the same A.R.D for the 2018 EWS season, this includes riding a stage on just the ARD as his tyre split. In the box you will get a pair of A.R.D Inserts and a pair of copper coloured tubeless valves. The tubeless valves have been specially made for Nukeproof to allow you to inflate and deflate the tyre easily with A.R.D fitted in the wheel. Want to shorten ARD to fit in smaller wheels? Download a step by step guide here How To Fit ARD Video Guide
Engineered specifically for the 2020 Nukeproof Reactor Alloy 275 and 290 models, this genuine Nukeproof protector provides an exceptional barrier against mud, muck and riding mishaps thanks to their durable moulded silicone construction. It attaches to your frame's downtube via its 3M adhesive backing and offers outstanding protection against all types of dirt and damage.
At 10mm shorter than Nukeproof's standard valve, this 35mm tubeless valve is less likely to be struck by trail debris such as rocks. The lower profile valve is complimented with further strength gains by using brass and a revised wall thickness. As a result, these updates make the valve super strong and only 2g heavier at 14g for the pair. As with Nukeproof's standard valves, this valve is fully compatible with tyre insert systems such as Nukeproof ARD and other brands. This model also benefits from a removable core, ensuring you can get the most airflow from your pump or cartridge. The head of this valve has also been designed to sit on top, enabling easier inflation and deflation. The same custom cap has been used with the integrated core remover, which allows for the core to be removed and fitted without specialist tools, while at the trailside or working from home. The nut has been designed so that you can get a good grip on the flat edges to firmly tighten the valve to the rim. An O-ring is included and sits against the outside of the rim to prevent damage from the nut tightening against the rim. How to Install Remove the valve cap and nut, insert the valve through the rim, fit the O-ring to the valve, thread on the nut and tighten by hand. Manufacturer's Part Number: NUKFTWG18AB-35LNF12R4BLK Black 35mm
Compatible with the 2020-2022 Reactor Carbon, this genuine Nukeproof protector is a fantastic barrier that's engineered from a durable moulded silicone construction. It attaches to your frame's downtube by its 3M adhesive backing and provides protection against dings, dirt, rocks and damage.