These end caps can be used to convert your hub to a different spacing or replace a lost cap. Compatibility Chart & How to Fit End Caps Please click here to determine which hubs can be converted, as the caps only fit the original specific hub options. End Caps: Changing end caps is simple and no tools are required. Just pull off the end caps on the hub and then push the new ones on. Where the end caps are not identical, the non-driveside always has the wider flange to cover the bearing. All caps sold as pairs and only compatible with Nukeproof Neutron V2 hubs.
This freehub body features a tough alloy construction, which makes it perfect for replacing your old or worn-out existing model. Suitable for use only on Nukeproof Horizon V2 hubs, this freehub body is designed for quick and easy installation. Options: · Shimano HG · Shimano Microspline · SRAM XD A new hub seal and bushing is supplied with Nukeproof freehubs. Please Note: The new hub seal will be fitted to the freehub for transport purposes. This needs to be removed from the freehub by pressing the pawls BEFORE fitting the freehub. Microspline freehubs also include the driveside end cap so you can easily convert an HG / XD hub to microspline If you are converting a microspline hub to XD or HG, you will also require a new driveside end cap which can be bought here ( ) This freehub is only compatible with Nukeproof Horizon V2 hubs. For step-by-step fitting instructions click here. Freehubs: Installation Instructions: 1. Remove driveside end cap 2. Pull off old freehub turning anticlockwise as you pull 3. Check hub seal for damage, if it is damaged remove the seal 4. If seal was removed, press on new seal 5. Apply grease hub ratchet ring 6. Apply thin grease to freehub pawls & springs then push onto hub shell turning anticlockwise 7. Refit driveside end cap
This set contains four pawls and four springs, plus a plastic cover for the freehub.
This kit contains all the parts needed to convert your 148mm Nukeproof Neutron HG / XD hub to have a microspline freehub. Please note this kit requires the hub to be stripped, a step by step guide to do this can be found here.
This non-driveside seal fits all Nukeproof Horizon and Neutron v2 rear hubs. Hub Seal Changing this seal is easy by following the instructions below: 1. Remove non-driveside end cap 2. Take a thin flat head screwdriver and gently prize off the old seal 3. Push new seal in place 4. Refit non-driveside end cap
Featuring an adapted head which allows the tyre insert to sit on top of the valve, the shape of the head allows for easy inflation and deflation. Each valve has a removable core allowing you to get maximum air flow from your tubeless pump or CO2 cartridge. The specially-designed custom cap features a core remover built in so you can remove & tighten the core without any additional tools. The nut has also been designed so that you can get a good grip on the flat edges to tighten the valve in the rim. An O-ring is also provided which sits against the outside of the rim and provides an airtight seal while preventing damage to the rim from the nut on the valve. How to Install Remove valve cap and nut, insert valve through rim, fit O-ring to valve then thread nut on and tighten by hand.
Bag of 100 gear ferrules
This LifeLine valve core remover helps prevent over-tightening and splitting of the valve stem.
38.8mm outer diameter
This will allow you to add air to any presta valve with a standard air chuck, making it ideal for that emergency stop at petrol/gas stations to top up your bike's tyre pressures.
Genuine Marzocchi part. Part Numbers: Extra Firm: MAZ-820-03-659-KIT Firm: MAZ-820-03-658-KIT Medium: MAZ-820-03-657-KIT Soft: MAZ-820-03-656-KIT
Ideal for use with various moving parts on your bike, this bearing features internal balls and lifelong lubrication for smooth performance and low maintenance. Thanks to the bearing's rubber sealing it also stays dust and dirt-free, and so is suitable for a multitude of extreme conditions.