Completely redesigned from the ground up, the Nukeproof Horizon V2 Front Wheel delivers fast and smooth-rolling performance across every inch of the mountain.Ready for fast-paced and aggressive trail-riding, this front wheel has gone through extensive testing to meet the demands of both Enduro and DH riders.It features a special blend of alloy material, which produces a hardness similar to 7-series alloy, but with the ductility and yield properties of a 6-series. This gives you the best of both worlds in terms of stiffness, strength and weight.Nukeproof has also ensured this front wheel's rim profile is the same as the rear (sold separately), the only difference is the front has a thinner sidewall for greater weight savings. One final highlight is it comes equipped with J-bend spokes, which means that tensioning and spoke replacement is as simple as possible. Enduro ABEC 5 BearingsAfter extensive testing with various brands of bearings, Nukeproof chose to use Enduro ABEC 5 bearings in this front wheel. These bearings have the “LLU/LLB” seal type, which uses two lips that make light contact in a groove to create a labyrinth where the water or dirt has a more difficult time to penetrate.LLU seals are similar, only the contact pressure or interference fit is greater to seal better. Enduro bearings have 80% grease fill on both sides whereas most other bearings have 35% grease fill on one side.This delivers full coverage, so there are no dry areas as well as avoiding metal on metal contact or wear. This means that the axle feels tight out of the box and after a couple of rides it will become free. Nukeproof Horizon V2 HubThis MTB front wheel features a revised Nukeproof Horizon V2 hub, which is available for both 15mm & 20mm spacings in both boost & non boost. We also sell end caps for QR separately. What's Included?Wheels come taped with tubeless valve installed so all you need to do is fit your tyre and add sealant. The tubeless valve supplied is the new Nukeproof Horizon valve which is compatible with Nukeproof ARD and other tyre inserts as well as the cap having a core remover built-in.Spoke length’s on Nukeproof wheels are the same regardless of spacing, the length changes with wheel size:27.5" Front Wheel: Non-Drive Side: 269, Driveside: 27029" Front Wheel: Non-Drive Side: 288, Driveside: 289 Conversion kits and replacement end caps available separately Key Features: Rim Material: Alloy Nukeproof Blend,Use: Trail, All Mountain, Enduro and DH,Spacing Options: 15x100mm; 15x110mm; 20x110mm Non Boost and 20x110mm Boost,Rim Width: Inner Width: 30mm; External Width: 35mm,Rim Height: 21.6mm,Tubeless Ready: Yes - Pretaped and valve supplied,Spoke Count: 32; Spoke Type: J-Bend; Lacing Pattern: 3x,Disc Mount: 6-Bolt,Build: Handbuilt,Weight: 27.5" 15mm Boost: 884g; 27.5" 20mm Boost: 946g.
Completely redesigned from the ground up, the Nukeproof Horizon V2 Front Wheel delivers fast and smooth-rolling performance across every inch of the mountain.Ready for fast-paced and aggressive trail-riding, this front wheel has gone through extensive testing to meet the demands of both Enduro and DH riders.It features a special blend of alloy material, which produces a hardness similar to 7-series alloy, but with the ductility and yield properties of a 6-series. This gives you the best of both worlds in terms of stiffness, strength and weight.Nukeproof has also ensured this front wheel's rim profile is the same as the rear (sold separately), the only difference is the front has a thinner sidewall for greater weight savings. One final highlight is it comes equipped with J-bend spokes, which means that tensioning and spoke replacement is as simple as possible. Enduro ABEC 5 BearingsAfter extensive testing with various brands of bearings, Nukeproof chose to use Enduro ABEC 5 bearings in this front wheel. These bearings have the “LLU/LLB” seal type, which uses two lips that make light contact in a groove to create a labyrinth where the water or dirt has a more difficult time to penetrate.LLU seals are similar, only the contact pressure or interference fit is greater to seal better. Enduro bearings have 80% grease fill on both sides whereas most other bearings have 35% grease fill on one side.This delivers full coverage, so there are no dry areas as well as avoiding metal on metal contact or wear. This means that the axle feels tight out of the box and after a couple of rides it will become free. Nukeproof Horizon V2 HubThis MTB front wheel features a revised Nukeproof Horizon V2 hub, which is available for both 15mm & 20mm spacings in both boost & non boost. We also sell end caps for QR separately. What's Included?Wheels come taped with tubeless valve installed so all you need to do is fit your tyre and add sealant. The tubeless valve supplied is the new Nukeproof Horizon valve which is compatible with Nukeproof ARD and other tyre inserts as well as the cap having a core remover built-in.Spoke length’s on Nukeproof wheels are the same regardless of spacing, the length changes with wheel size:27.5" Front Wheel: Non-Drive Side: 269, Driveside: 27029" Front Wheel: Non-Drive Side: 288, Driveside: 289 Conversion kits and replacement end caps available separately Key Features: Rim Material: Alloy Nukeproof Blend,Use: Trail, All Mountain, Enduro and DH,Spacing Options: 15x100mm; 15x110mm; 20x110mm Non Boost and 20x110mm Boost,Rim Width: Inner Width: 30mm; External Width: 35mm,Rim Height: 21.6mm,Tubeless Ready: Yes - Pretaped and valve supplied,Spoke Count: 32; Spoke Type: J-Bend; Lacing Pattern: 3x,Disc Mount: 6-Bolt,Build: Handbuilt,Weight: 27.5" 15mm Boost: 884g; 27.5" 20mm Boost: 946g.
Completely redesigned from the ground up, the Nukeproof Horizon V2 Rear Wheel 102t delivers fast and smooth-rolling performance across every inch of the mountain.Ready for fast-paced and aggressive trail-riding, this rear wheel has gone through extensive testing to meet the demands of both Enduro and DH riders. It features a special blend of alloy material, which produces a hardness similar to 7-series alloy, but with the ductility and yield properties of a 6-series.This gives you the best of both worlds in terms of stiffness, strength and weight. Nukeproof has also ensured this rear wheel's rim profile is the same as the front (sold separately), the only difference is the rear has a thicker sidewall for added strength on the trails. One final highlight is it comes equipped with J-bend spokes, which means that tensioning and spoke replacement is as simple as possible. Enduro ABEC 5 BearingsAfter extensive testing with various brands of bearings, Nukeproof chose to use Enduro ABEC 5 bearings in this rear wheel. These bearings have the “LLU/LLB” seal type, which uses two lips that make light contact in a groove to create a labyrinth where the water or dirt has a more difficult time to penetrate. LLU seals are similar, only the contact pressure or interference fit is greater to seal better.Enduro bearings have 80% grease fill on both sides whereas most other bearings have 35% grease fill on one side. This delivers full coverage, so there are no dry areas as well as avoiding metal on metal contact or wear. This means that the axle feels tight out of the box and after a couple of rides it will become free.Nukeproof Horizon V2 Hub This MTB rear wheel features a revised Nukeproof Horizon V2 hub that now has 102 points of engagement and comes in a range of freehub options. Freehubs are also available separately and easily changeable if you choose upgrade your drivetrain in the future.Nukeproof's 142mm hub can be converted to 135mm QR and the 148mm hub can be converted to 141mm using end caps. The hub has also been machined to remove excess material and make it as strong and light as possible. Nukeproof has fitted these hubs with our louder pawls & springs, this gives the wheel a nice buzz as you head down the trail. If you prefer the quiet life, you can get the quieter ones which are available separately.What's Included? Wheels come taped with tubeless valve installed so all you need to do is fit your tyre and add sealant. The tubeless valve supplied is the new Nukeproof Horizon valve which is compatible with Nukeproof ARD and other tyre inserts aswell as the cap having a core remover built in.A full range of spares are available to service your hub in the future.Spoke length’s on Nukeproof wheels are the same regardless of spacing, the length changes with wheel size:Rear 27.5" Wheel: Non-Drive Side: 271, Driveside: 268 Rear 29" Wheel: Non-Drive Side: 289, Driveside: 286 Key Features: Rim Material: Alloy Nukeproof Blend,Use: Trail / All Mountain / Enduro / DH,Rim Width: Inner: 30mm; External: 35mm; Rim Height: 21.6mm,Spacing Options: 142x12mm; 148x12mm; 150/157x12mm,Conversion options: 142x12mm can be converted to 135mm QR, 148x12mm can be converted to 141mm Boost with end caps (sold separately),Rear hub engagement: 102 points of engagement (every 3.52 degrees),Freehub options: Shimano HG, Shimano Microspline, SRAM XD,Spoke Type: J-Bend; Spoke count: 32; Lacing pattern: 3x,Disc Mount: 6-Bolt,Tubeless Ready: Yes - Pre-taped and valve supplied;,Build: Handbuilt .
These tubeless valves are universal and have also been designed to work with tubeless tyre inserts. These durably-made valves are ideal for efficient inflation. The adapted head allows the tyre insert to sit on top of the valve, with the shape of the head allowing for easy inflation and deflation. Each valve has a removable core allowing you to get maximum air flow from your tubeless pump or CO2 cartridge. The custom cap has been specially designed and has an integrated core remover for removing and tightening the core without any additional tools. The nut has also been designed so that you can get a good grip on the flat edges to firmly tighten the valve on the rim. An O-ring is included and sits against the outside of the rim to prevent damage to the rim. How to InstallRemove valve cap and nut, insert valve through rim, fit o-ring to valve then thread nut on and tighten by hand. Key Features: Valve Type: Presta,Includes: Integrated valve core remover cap, O-ring, removable core,Easy installation,Sold as a pair,Weight: 12g per pair.
This durable and dependable Nukeproof tubeless tape has been tested by its in-house team and athletes to ensure a firm and effective seal. Made to meet the demands of downhill and enduro racing, it does a sterling job in keeping your tubes protected as you take on the most daring descents and trails.One 10-metre roll will be enough tape to cater for 4x 29” wheels. One layer with a 4” overlap is all that is required to tape your wheel for tubeless setup. Instructions for Use: Remove any old tape and sealant residue,Ensure rim is clean and dry,Start opposite the valve hole and maintain tension as you apply tape,Work air bubbles out as you tape the wheel (Push them out via the spoke holes),Apply one layer of tape with a 4" overlap,Ensure all air bubbles have been removed and tape is fully stuck right out to the edges of the rim,Pierce a small hole and insert your valve,.Features:Length: 10mSuitability: Downhill, Enduro
The Nukeproof Neutron V2 Freehub Body 36t is designed for use with Nukeproof Neutron V2 hubs.A new hub seal and bushing is supplied with Nukeproof freehubs. To avoid damage to the hub seal, turn the freehub anti-clockwise as you fit. Options: Shimano HG,Shimano Microspline,SRAM XD,.If you have a HG / XD hub and want to convert to microspline, you will need Nukeproof's microspline conversion kit (Part Number: NUKNEUV236MSCONV). Key Features: Material: Alloy,Use: MTB,Pawl: 4-pawl,Hub Compatibility: Nukeproof Neutron V2,Cassette Compatibility: Shimano HG - 9, 10, 11 and 12 Shimano HG spline cassettes; SRAM XD - SRAM Eagle XD Cassettes or Shimano Microspline - Shimano microspline cassettes,Points of Engagement: 36,.This freehub is only compatible with Nukeproof Neutron V2 hubs
The Nukeproof Neutron V2 Front Wheel has been completely redesigned from the ground up and gives riders incredibly fast and smooth-rolling performance on every ride.This front wheel features a Nukeproof Neutron front hub that is available for both 15mm or 20mm spacings in both Boost and non-Boost. Nukeproof also sell end caps for QR (available separately).The 6066 alloy rim has been extensively to ensure it is a rim which is light enough for aggressive trail riding but strong enough for DH.Nukeproof have used J-Bend spokes meaning tensioning and spoke replacement is much simpler than using a straight pull spoke.The wheels come taped with tubeless valve installed so all you need to do is add sealant and your tyre to get a finished tubeless setup. The valve supplied is Nukeproofs Horizon valve which also has a core remover built into the cap. This valve is also compatible with tyre inserts like Nukeproof ARD. Spoke length’s on the front wheels are the same regardless of spacing, the length changes with wheel size: Front 27.5" Wheel: Non-Driveside: 272, Driveside: 273, Front 29" Wheel: Non-Driveside: 291, Driveside: 292,.Conversion kits and replacement end caps available separately. Key Features: Rim Material: 6066 Alloy,Use: MTB, Trail, All Mountain, Enduro and DH,Wheel Size: 27.5" or 29" options available,Spacing Options: 15x100mm, 15x110mm, 20x110mm Non Boost, 20x110mm Boost,Spokes: Spoke Type: J-Bend; Spoke Count: 32; Lacing Pattern: 3x,Disc Mount: 6-bolt,Width: Inner Rim Width: 29mm; External Rim Width: 33mm; Rim Height: 18mm,Tubeless Ready: Yes - Pretaped and valve supplied.
The Nukeproof Neutron V2 Rear Wheel 36t has been completely redesigned from the ground up and gives riders incredibly fast and smooth-rolling performance on every ride.This rear wheel features 36 points of engagement and comes in a range of freehub options. Nukeproof has also made freehubs available separately and easy to change if you choose to upgrade your drivetrain in the future.The 142mm hub can be converted to 135mm QR and the 148mm hub can be converted to 141mm using end caps. The hub has been machined to remove excess material and make it as strong and light as possible. Nukeproof have increased the thickness of pawl springs in these hubs to give secure engagement on every pedal stroke.The 6066 alloy rim has been extensively to ensure it is a rim which is light enough for aggressive trail riding but strong enough for DH.Nukeproof have used J-Bend spokes meaning tensioning and spoke replacement is much simpler than using a straight pull spoke.The wheels come taped with tubeless valve installed so all you need to do is add sealant and your tyre to get a finished tubeless setup. The valve supplied is Nukeproof's Horizon valve which also has a core remover built into the cap. This valve is also compatible with tyre inserts like Nukeproof ARD.Spoke length’s on the front wheels are the same regardless of spacing, the length changes with wheel size:Wheelsize: 27.5", Spacing: 142mm / 148mm x 12mm, Non-Driveside: 274, Driveside: 272Wheelsize: 27.5", Spacing: 150mm / 157mm x 12mm, Non-Driveside: 274, Driveside: 273Wheelsize: 29", Spacing: 142mm / 148mm x 12mm, Non-Driveside: 292, Driveside: 290Wheelsize: 29", Spacing: 150mm / 157mm x 12mm, Non-Driveside: 292, Driveside: 291Conversion kits and replacement end caps available separately.Key Features: Rim Material: 6066 Alloy, Use: MTB, Trail, All Mountain, Enduro and DH, Spacing Options: 142x12mm, 148x12mm, 150/157x12mm, Conversion Options: 142x12mm can be converted to 135mm QR; 148x12mm can be converted to 141mm Boost with end caps (sold separately), Rear Hub Engagement: 36 points of engagement (every 10 degrees), Freehub Options: Shimano HG, Shimano Microspline or SRAM XD, Spokes: Spoke Type: J-Bend; Spoke Count: 32; Lacing Pattern: 3x; Disc Mount: 6-bolt, Width: Inner Rim Width: 29mm; External Rim Width: 33mm; Rim Height: 18mm, Tubeless Ready: Yes - Pretaped and valve supplied; Single or Pair: Single, Weight: 15mm Boost Front: 905g including valve & tape; 148mm Boost HG Rear: 1045g including valve and tape.
The Nukeproof Neutron V2 Rear Wheel 36t has been completely redesigned from the ground up and gives riders incredibly fast and smooth-rolling performance on every ride.This rear wheel features 36 points of engagement and comes in a range of freehub options. Nukeproof has also made freehubs available separately and easy to change if you choose to upgrade your drivetrain in the future.The 142mm hub can be converted to 135mm QR and the 148mm hub can be converted to 141mm using end caps. The hub has been machined to remove excess material and make it as strong and light as possible. Nukeproof have increased the thickness of pawl springs in these hubs to give secure engagement on every pedal stroke.The 6066 alloy rim has been extensively to ensure it is a rim which is light enough for aggressive trail riding but strong enough for DH.Nukeproof have used J-Bend spokes meaning tensioning and spoke replacement is much simpler than using a straight pull spoke.The wheels come taped with tubeless valve installed so all you need to do is add sealant and your tyre to get a finished tubeless setup. The valve supplied is Nukeproof's Horizon valve which also has a core remover built into the cap. This valve is also compatible with tyre inserts like Nukeproof ARD.Spoke length’s on the front wheels are the same regardless of spacing, the length changes with wheel size:Wheelsize: 27.5", Spacing: 142mm / 148mm x 12mm, Non-Driveside: 274, Driveside: 272Wheelsize: 27.5", Spacing: 150mm / 157mm x 12mm, Non-Driveside: 274, Driveside: 273Wheelsize: 29", Spacing: 142mm / 148mm x 12mm, Non-Driveside: 292, Driveside: 290Wheelsize: 29", Spacing: 150mm / 157mm x 12mm, Non-Driveside: 292, Driveside: 291Conversion kits and replacement end caps available separately.Key Features: Rim Material: 6066 Alloy, Use: MTB, Trail, All Mountain, Enduro and DH, Spacing Options: 142x12mm, 148x12mm, 150/157x12mm, Conversion Options: 142x12mm can be converted to 135mm QR; 148x12mm can be converted to 141mm Boost with end caps (sold separately), Rear Hub Engagement: 36 points of engagement (every 10 degrees), Freehub Options: Shimano HG, Shimano Microspline or SRAM XD, Spokes: Spoke Type: J-Bend; Spoke Count: 32; Lacing Pattern: 3x; Disc Mount: 6-bolt, Width: Inner Rim Width: 29mm; External Rim Width: 33mm; Rim Height: 18mm, Tubeless Ready: Yes - Pretaped and valve supplied; Single or Pair: Single, Weight: 15mm Boost Front: 905g including valve & tape; 148mm Boost HG Rear: 1045g including valve and tape.
The Nukeproof Horizon V2 Freehub Body 102t is specifically designed for replacing the freehub body on Nukeproof Horizon V2 hubs.This freehub body features a tough alloy construction, which makes it perfect for replacing your old or worn-out existing model. Suitable for use only on Nukeproof Horizon V2 hubs, this freehub body is designed for quick and easy installation. Options: Shimano HG,Shimano Microspline,SRAM XD,.A new hub seal and bushing is supplied with Nukeproof freehubs.Microspline freehubs also include the driveside end cap so you can easily convert an HG / XD hub to microsplineIf you are converting a microspline hub to XD or HG, you will also require a new driveside end cap.This freehub is only compatible with Nukeproof Horizon V2 hubs. Key Features: Material: Alloy,Pawl: 6-Pawl,Hub Compatibility: Horizon V2,,Cassette Compatibility: Shimano HG - 9, 10, 11 and 12 Shimano HG spline cassettes; SRAM XD - SRAM Eagle XD Cassettes; Shimano Microspline - Shimano microspline cassettes,Points of Engagement: 102,Nukeproof Part Numbers: Shimano HG Freehub: NUKHORV2102TFHHG; SRAM XD Freehub: NUKHORV2102TFHXD; Shimano Microspline Freehub: NUKHORV2102TFHMS.
The Nukeproof Horizon V2 Pawls & Springs are direct replacements for use with your Nukeproof Horizon V2 hubs.These pawls and springs come as a replacement set of six pawls and six springs, which includes the plastic cover for the Nukeproof Horizon V2 freehub.Nukeproof offers two options which are loud or quiet. This is due to Nukeproof hubs coming with the loud pawls and springs pre-installed as standard, but there is also the option for a quieter ride if you prefer it. Key Features: Use: MTB, Compatibility: Nukeproof Horizon V2 hubs,Includes: x6 pawls; x6 springs plus Plastic cover for the freehub,Nukeproof Part Numbers:, Loud: NUKHORV2PSGOLD,Quiet: NUKHORV2PSSIL, ..