The Old Skool IIII Backpack is a favorite for good reason. This classic backpack features an all-purpose, two pocket design with an organizer in the front to ensure that your important items stay neatly arranged, and an interior laptop sleeve so you can easily take your gear on the go. The side water bottle pocket and allover tie-dyed print bring an �Off The Wall� touch to this iconic design.
The Milford Beanie is made with 100% acrylic and features a cuff with an authentic Vans patch.
The Parkview Cuff Beanie features an allover tie dye for a bold new take on the classic cuffed beanie. Made with acrylic and finished with a signature Vans woven clamp label, this ribbed beanie elevates any look.
Designed in conjunction with Chris King, Peaty's MK2 Tubeless Valves are made from premium lightweight, high strength 7075 aluminium, and fit most tubeless setups from MTB to road and cyclocross, including carbon, enduro and DH rims.Lightweight & durable 7050 aluminium constructionColoured to match Chris King componentsSlotted base compatible with or without tyre insertsValve caps double as 3.4mm spoke key and valve core removal toolThe unique x-cut base has been designed to work with all tyre inserts. The channels cut into the base of the valve allow air and sealant to pass through when inserts are pushed up against them. Unlike most other insert-compatible valves, the MK2 valves have a straight-through design so there's no reduction of sealant or air flow when tyre inserts are not used.Fitting couldn't be easier. integrated o-rings prevent the lock rings from scratching your precious rims and large soft rubber bases easily create an airtight seal. Designed by riders, for riders. Our valves come as standard with an integrated valve core remover cap and spoke key cap (for standard 3.4mm spoke nipples). This makes tightening loose spokes and topping up with sealant a breeze, either in the workshop or out on the trails.
The Nutcase Baby Nutty MIPS helmet has been an industry leader for safety and comfort for the last 3 years. Updated design provides maximum comfort and fit while allowing optimal head support and postureRotational motion and force can cause brain injuries in our little nutty's. MIPS is a low-friction layer that sits between your baby's brain and the helmet. The liner slides 5 to 15mm in all directions if there was an impact, reducing forces to their brainLightweight polycarbonate outer shell designed with baby neck strength in mindUpdated Fidlock snap-and-go magnetic buckle system means your baby won't get pinched which means no tears! 11 contoured vents for effective coolingHeat-sealed, 3-piece pad set and GROW Flex Fit System cradle the head and provide individual fit and comfortEngineered, tested and CPSC-certified for 1 year of age and olderSize: 48cm-52cmUpdated for 2020 featuring the MIPS safety feature and their baby specific EPS protective foam, designed to disperse any force and protect their growing brains! The updated design provides maximum comfort and fit, while focusing on head support and posture for their little neck and head. No pinching and no tears with our updated Fidlock magnetic buckle system.
Everyone knows that a straight line is the fastest line! That's why Peaty's made their Holeshot CO2 tyre inflator straight, rather than bent at 90 degrees. This straight line design enables faster airflow for rapid inflation and creates less stress on your tubeless valves when you're using it because you're coming at the valve straight on rather than at a 90 degree angle.Available in 12x Chris King coloursUnique Patent Pending compact straight line design for maximum airflowSimply push down to inflateUnique closed base silicone Freeze protector sleeve prevents your hands from freezing, even without glovesEach kit contains 1x inflator head, 2x CO2 cartridges and 1x freeze protector sleeveIt's as small and lightweight as possible, so it's easy to carry in your pocket, bag or strapped to your bikeMade from CNC'd 6061 aluminium, and with a patent pending valve design, the details of Peaty's inflator heads have been agonised on - from the exact rubber compound of the O-rings to the awesome Chris King anodized colours. Not stopping at the inflator head, Peaty's applied the same level of detail and quality in making a high quality CO2 cartridge sleeve. far from a cheap strip of neoprene, our freeze protector sleeve is made from temperature resistant silicone and has a unique closed base to stop your hand from freezing to the cartridge, no matter how you hold it - even without wearing gloves.
Everyone knows that a straight line is the fastest line! That's why Peaty's made their Holeshot CO2 tyre inflator straight, rather than bent at 90 degrees. This straight line design enables faster airflow for rapid inflation and creates less stress on your tubeless valves when you're using it because you're coming at the valve straight on rather than at a 90 degree angle.Available in 12x Chris King coloursUnique Patent Pending compact straight line design for maximum airflowSimply push down to inflateUnique closed base silicone Freeze protector sleeve prevents your hands from freezing, even without glovesEach kit contains 1x inflator head, 2x CO2 cartridges and 1x freeze protector sleeveIt's as small and lightweight as possible, so it's easy to carry in your pocket, bag or strapped to your bike. Made from CNC'd 6061 aluminium, and with a patent pending valve design, the details of Peaty's inflator heads have been agonised on - from the exact rubber compound of the O-rings to the awesome Chris king anodized colours.Not stopping at the inflator head, Peaty's applied the same level of detail and quality in making a high quality CO2 cartridge sleeve. far from a cheap strip of neoprene, our freeze protector sleeve is made from temperature resistant silicone and has a unique closed base to stop your hand from freezing to the cartridge, no matter how you hold it - even without wearing gloves.
Peaty's unique single-sided fork design allows for multiple plug sizes to be easily rolled into the dip of the fork and pushed straight into the tyre. The open side to the fork then allows for the tool to be easily pulled back out of the hole without pulling the plug out with it.Available in 12x Chris King coloursQuick and easy to insert tyre plugs. With our unique single-sided fork design, you simply push and roll the plug into the hook of the forkWith no tight gap to squeeze through, the plug is far less likely to pull back out when the tool is extracted the fork is sharp tipped & as slim as possible, so it doesn't widen the size of the - hole already thereFork made from 316 stainless steelBody made from anodised 6061 aluminiumKnurled body and ribbed lid / handle for extra gripWeather sealing O-rings make the tool waterproof when assembledEach kit comes with one sheet of 3x 1.5mm and one sheet of 3x 3mm plugsMade from high quality 316 Stainless steel, the fork is designed to be as short as possible to reduce the chance of you puncturing your rim tape when inserting a plug. The fork has also been designed with a reaming texture on the shaft, to clean out punctures before plugging, and to be as slim as possible, so it doesn't widen the size of the hole already there.Shrinking down to a tiny 65mm x 19mm, this tool has been designed to easily fit into your pocket or slot into a tool wrap or backpack. With knurling on the tool base and ribbing on the lid, you shouldn't have any issues gripping the tool, even in the muddiest of conditions.Simply unscrew the lid and thread it onto the rear of the tool to make a sturdy handle to hold onto while inserting the plug. This pack includes three thick (3mm) plugs and three thin (1.5mm) plugs. These plug sheets can be neatly wrapped around the fork and stored neatly inside the compact water-sealed body. Holeshot refill plug sheets also sold separately packaged with cardboard header cards & in biodegradable bags.
Designed in conjunction with Chris King, Peaty's MK2 Tubeless Valves are made from premium lightweight, high strength 7075 aluminium, and fit most tubeless setups from MTB to road and cyclocross, including carbon, enduro and DH rims.Lightweight & durable 7050 aluminium constructionColoured to match Chris King componentsSlotted base compatible with or without tyre insertsValve caps double as 3.4mm spoke key and valve core removal toolThe unique x-cut base has been designed to work with all tyre inserts. The channels cut into the base of the valve allow air and sealant to pass through when inserts are pushed up against them. Unlike most other insert-compatible valves, the MK2 valves have a straight-through design so there's no reduction of sealant or air flow when tyre inserts are not used.Fitting couldn't be easier. integrated o-rings prevent the lock rings from scratching your precious rims and large soft rubber bases easily create an airtight seal. Designed by riders, for riders. Our valves come as standard with an integrated valve core remover cap and spoke key cap (for standard 3.4mm spoke nipples). This makes tightening loose spokes and topping up with sealant a breeze, either in the workshop or out on the trails.
Designed in conjunction with Chris King, Peaty's MK2 Tubeless Valves are made from premium lightweight, high strength 7075 aluminium, and fit most tubeless setups from MTB to road and cyclocross, including carbon, enduro and DH rims.Lightweight & durable 7050 aluminium constructionColoured to match Chris King componentsSlotted base compatible with or without tyre insertsValve caps double as 3.4mm spoke key and valve core removal toolThe unique x-cut base has been designed to work with all tyre inserts. The channels cut into the base of the valve allow air and sealant to pass through when inserts are pushed up against them. Unlike most other insert-compatible valves, the MK2 valves have a straight-through design so there's no reduction of sealant or air flow when tyre inserts are not used.Fitting couldn't be easier. integrated o-rings prevent the lock rings from scratching your precious rims and large soft rubber bases easily create an airtight seal. Designed by riders, for riders. Our valves come as standard with an integrated valve core remover cap and spoke key cap (for standard 3.4mm spoke nipples). This makes tightening loose spokes and topping up with sealant a breeze, either in the workshop or out on the trails.
Whether you've lost a valve cap or just want to bling your existing pair of Peaty's valves, this kit gives you everything you need. Compatible with all Peaty's Tubeless Valves. Includes: 1x spoke key cap (for 3.4mm spoke nipple), 1x valve core remover cap & 2x lock rings.
The DMR Vault V2 Pedal is a much-loved classic flat pedal that s ideal for all types of mountain bike riding. They are however especially liked by all mountain and downhill riders due to their large platform, easy servicing and outstanding levels of grip.Lightweight at 430g per pairTough & durable extruded 6061 Aluminium & 4140 CroMo steel axlesServiceable high load DU bush & cartridge bearingReplaceable pinsThe large platform gives you tremendous stability, a huge amount of grip and excellent mud clearance thanks to the open body design. Constructed from tough 6061 aluminium these pedals are the epitome of tough.The pins are reversible, so you can customise these pedals to your liking; from long and sharp to short and more rounded. A sealed bearing keeps out all that muck and wet that you ll inevitably encounter while servicing is just a case of removing a 6mm dust cap and applying fresh grease.The DMR Vault V2 are a highly durable, light flat pedal that offers almost unrivalled grip and the only choice left to make is what colour you d like them in.