Key Features:Compatible with all cable-actuated dropper posts.,Works with dropper posts that (a) have the barrel end of the cable at the remote position and (b) those that have the barrel end at the seat post.,If your post is not listed in the charts found in the image gallery, wolf tooth recommends measuring the pivot centre to end of your current lever. If it is greater than 52mm the light action will work best. If it is less than 52mm, the standard remote will work best.Mounting types:,Remote 22.2mm - includes hinged handlebar clamp for 22.2mm handlebars. All mountain bike handlebars are 22.2mm where your shift and brake levers attach even on 31.8mm handlebars. (31.8mm and 35mm handlebars just refer to the diameter where the stem clamps). Attach with 1-2nm max..
These limited edition Wolf Tooth ReMote Dropper Levers in anodised colours are ergonomic, lightweight and easy to install. Utilising sealed cartridge bearings for a silky-smooth action and a low profile, textured lever machined to the highest quality, this is the ultimate dropper upgrade.Compatible with all cable actuated dropper posts, the ReMote Dropper Lever is simple to install, maintain and has been built to last. Every single detail of the ReMote is the result of a singular drive to eliminate all complaints found with stock dropper levers.In an industry first, the ReMote uses a 21mm sealed cartridge bearing for smooth operation and unparalleled modulation. A precision-machined cable path and custom clamping screw with captive washer won’t damage cables like more common set screws. As an added bonus, cables can be cut to length and crimped prior to securing.The ReMote lever sits close to the bar, minimizing the distance the thumb must be removed from the grip while reducing the likelihood of knee contact in technical terrain and adds a bit of extra length to overcome stiff dropper internals.Wolf Tooth's team have also included an innovative engineered failure point, allowing the lever to break away from its base in the event of a crash. Replacement axles are inexpensive and readily available, ensuring that you can spend more time on the trails and less time in the workshop.Wolf Tooth ReMote Installation InstructionsCompatibility:Compatible with all cable actuated dropper posts.,Works with dropper posts that (a) have the barrel end of the cable at the remote position and (b) those that have the barrel end at the seat post. ,If your post is not listed in the charts found in the image gallery, Wolf Tooth recommends measuring the pivot centre to end of your current lever. If it is greater than 52mm the Light Action will work best. If it is less than 52mm, the Standard ReMote will work best..Mounting Types:ReMote 22.2mm - includes hinged handlebar clamp for 22.2mm handlebars. All mountain bike handlebars are 22.2mm where your shift and brake levers attach even on 31.8mm handlebars. (31.8mm and 35mm handlebars just refer to the diameter where the stem clamps). Attach with 1-2nm max.
The Wolf Tooth Premium IS Headsets for Specialized are made exclusively for Specialized frames with moulded-in internal bearing cups and a 42mm upper bearing diameter.Machined at Wolf Tooth’s Minnesota shop with aircraft-grade 6061 aluminium and with three levels of industry leading custom sealing, these headsets are designed to be lightweight, strong and durable. The headsets use Enduro stainless steel bearings which are built to the highest specifications for lasting quality.The stack on the headsets is 3mm and is available in Wolf Tooth’s signature anodised colours. Key Features: IS (Integrated Standard) headset for any Specialized bike that uses a 42mm upper bearing,Uppers and lowers sold separately,Enduro stainless stell bearings in upper and lower,Lifetime warranty,Weight: 43g (3mm),Material: 6061 aluminium,Stem cap torque spec: 2–3Nm with light grease on threads only,Made in the USA,. Upper Assembly Features: Ultralight Stem Cap with 5mm Integrated Spacer plus an aluminium bolt and a star nut,One 3mm stack height top cover option,O-ring seal prevents water intrusion around steerer tube,Custom-moulded upper lip seal provides additional protection for upper bearing,. Compatible Models: Aluminum Mountain Bikes (all except Chisel HT aluminum),Camber Carbon | 2014,Chisel Alloy HT (Smartweld HT) | 2017-2021,Enduro 29 Carbon | 2014,Enduro Carbon | 2017, 2020,Epic Carbon | 2014,Epic FSR | 2021,Epic FSR Carbon | 2018,Epic HT | 2017, 2020,Fatboy Carbon | 2015,Fuse Carbon | 2017,Stumpjumper | 2021,Stumpjumper Carbon | 2019,Stumpjumper EVO | 2021,Stumpjumper FSR Carbon | 2016.
The Wolf Tooth Performance External Cup Headset is machined in the USA from aircraft-grade 6061 aluminium, to ensure a lightweight, strong, and durable design.The headset uses Enduro chromium steel bearings with a black oxide treatment for superb durability and high load capacities.The headset has three levels of superior custom sealing to protect bearings from the elements and prolong the life of the headset.The Performance headset comes with a 1-year warranty. Key Features: Compatible with any frame that uses an external cup headset with a 34mm upper head tube inner diameter and 34mm, 44mm, or 49mm lower head tube inner diameter.,Stack height designation for EC headsets includes 10mm cup (see tech specs).,Uppers and lowers sold separately.,Enduro black oxide sealed bearings included on both the upper and lower.,Upper headsets ship with a star nut which can only be used on forks with steel or aluminium steerer tubes. For forks with carbon steerer tubes you will need a compression plug (sold separately). (Never use a star nut on a carbon steerer tube).,1-year warranty,Weight: 55-58g,Material 6061 aluminium, Made in the USA,. Lower Assembly Features: Custom moulded dual-lip seal on the crown race to protect lower bearing in the toughest conditions.,12.25mm stack.,Service and additional parts available..
The Wolf Tooth Performance External Cup Headset is machined in the USA from aircraft-grade 6061 aluminium, to ensure a lightweight, strong, and durable design.The headset uses Enduro chromium steel bearings with a black oxide treatment for superb durability and high load capacities.The headset has three levels of superior custom sealing to protect bearings from the elements and prolong the life of the headset.The Performance headset comes with a 1-year warranty. Key Features: Compatible with any frame that uses an external cup headset with a 34mm upper head tube inner diameter and 34mm, 44mm, or 49mm lower head tube inner diameter.,Stack height designation for EC headsets includes 10mm cup (see tech specs).,Uppers and lowers sold separately.,Enduro black oxide sealed bearings included on both the upper and lower.,Upper headsets ship with a star nut which can only be used on forks with steel or aluminium steerer tubes. For forks with carbon steerer tubes you will need a compression plug (sold separately). (Never use a star nut on a carbon steerer tube).,1-year warranty,Weight: 55-58g,Material 6061 aluminium, Made in the USA,. Upper Assembly Features: Ultralight Stem Cap with Integrated Spacer plus an aluminium bolt and a star nut.,5mm top cover = 16mm total stack.,O-ring seal prevents water intrusion around the steerer tube.,Custom-moulded upper lip seal provides additional protection for upper bearing. .
The Wolf Tooth Performance Zero Stack Headset is machined in the USA from aircraft-grade 6061 aluminium, to ensure a lightweight, strong, and durable design.The headset uses Enduro chromium steel bearings with a black oxide treatment for superb durability and high load capacities.The headset has three levels of superior custom sealing to protect bearings from the elements and prolong the life of the headset.The Performance headset comes with a 1-year warranty. Key Features: Any frame that uses ZS (Zero Stack) headsets with 44mm upper and 56mm lower head tube inner diameter., Uppers and lowers sold separately., Enduro black oxide steel sealed bearings included on both the upper and lower., Upper headsets ship with a star nut which can only be used on forks with steel or aluminium steerer tubes. For forks with carbon steerer tubes you will need a compression plug (sold separately). (Never use a star nut on a carbon steerer tube) ,1-year warranty., Weight: 55-58g, Material: 6061 aluminium, Made in the USA,. Lower Assembly Features: Custom-moulded dual-lip seal on the crown race protects lower bearing in the toughest conditions.,All components precision machined in-house at Wolf Tooth from aircraft grade aluminium to ensure the highest level of quality..
The Wolf Tooth Performance Integrated Standard Headset is machined in the USA from aircraft-grade 6061 aluminium, to ensure a lightweight, strong, and durable design.The headset uses Enduro chromium steel bearings with a black oxide treatment for superb durability and high load capacities.The headset has three levels of superior custom sealing to protect bearings from the elements and prolong the life of the headset.The Performance headset comes with a 1-year warranty. Key Features: Compatible with any frame that uses Integrated Standard headsets with 41mm upper and 52mm lower outer bearing diameter,Uppers and lowers sold separately,Enduro black oxide steel sealed bearings included on both the upper and lower., Upper headsets ship with a star nut which can only be used on forks with steel or aluminium steerer tubes. For forks with carbon steerer tubes you will need a compression plug (sold separately). (Never use a star nut on a carbon steerer tube).,1-year warranty,Weight: 7mm, 52g,Material: 6061 aluminium,Made in the USA,. Upper Assembly Features: Ultralight Stem Cap with Integrated Spacer plus an aluminium bolt and a star nut., 7mm top cover = 8mm total stack., O-ring seal prevents water intrusion around steerer tube.,Custom-moulded upper lip seal provides additional protection for upper bearing..
The ReMote Light Action Dropper Lever has a longer lever arm than the standard ReMote, reducing the actuation force required by a third and making it ideal for dropper posts with a harder pull or if you prefer a light actuation feel.Every single detail of the ReMote Light Action is the result of a singular drive to eliminate all complaints found with stock dropper levers.In an industry first, the ReMote uses a 21mm sealed cartridge bearing for smooth operation and unparalleled modulation. A precision-machined cable path and custom clamping screw with captive washer won’t damage cables like more common set screws. As an added bonus, cables can be cut to length and crimped prior to securing.The ReMote lever sits close to the bar, minimizing the distance the thumb must be removed from the grip while reducing the likelihood of knee contact in technical terrain and adds a bit of extra length to overcome stiff dropper internals.Wolf Tooth's team have also included an innovative engineered failure point, allowing the lever to break away from its base in the event of a crash. Replacement axles are inexpensive and readily available, ensuring that you can spend more time on the trails and less time in the workshop.Wolf Tooth ReMote Installation Instructions Compatibility: Compatible with all cable actuated dropper posts., Works with dropper posts that (a) have the barrel end of the cable at the remote position and (b) those that have the barrel end at the seat post.,If your post is not listed in the charts found in the image gallery, Wolf Tooth recommends measuring the pivot centre to end of your current lever. If it is greater than 52mm the Light Action will work best. If it is less than 52mm, the Standard ReMote will work best.,. Mounting Types: ReMote 22.2mm - includes hinged handlebar clamp for 22.2mm handlebars. All mountain bike handlebars are 22.2mm where your shift and brake levers attach even on 31.8mm handlebars. (31.8mm and 35mm handlebars just refer to the diameter where the stem clamps). Attach with 1-2nm max.,ReMote IS-AB for Shimano I-Spec A or B - Includes IS-AB hardware.,ReMote IS-II for Shimano I-Spec II - Includes IS-II hardware.,ReMote MM SRAM/Avid MatchMaker X - Includes the MatchMakerX hardware, which is a T-Nut and bolt that allows the ReMote MM to attach to the MatchMakerX clamp. You will need the MatchMakerX handlebar clamp, which we do not sell but can easily be purchased.,ReMote 31.8 is available for road bikes where the ReMote is mounted next to the stem.,ReMote Magura for Magura brakes and some 2-bolt clamp SRAM brakes - Includes Magura hardware,ReMote Hope for Tech3 Hope Brakes - Includes Hope hardware (see compatibility above),ReMote IS-EV for Shimano I-Spec EV - Includes IS-EV hardware.
Any dropper post with a 25mm or 26mm stanchion diameter - when in doubt, measure your stanchion.,Note that discrete position droppers will likely lose the lowest position because the valais 25 reduces the dropper travel by 25mm,Valais 25.25 (posts that have a confirmed 25mm diameter)Easton haven,Giant contact (internal routing),Raceface turbine,Rockshox reverb stealth,Specialized command post,9point8 fall line,Other 24.75-25.25mm (cable routing dependent),.,· valais 25.26 (posts that have a confirmed 26mm diameter)Thomson covert,Fox transfer,Other 26-26.5mm (cable routing dependent),.,Valais limits the dropper travel by at least 25mm. There are 2 models as noted in the compatibility section, one for the 25mm diameter stanchions and one for the 26mm stanchions.,At full compression, the valais' deep skirt contacts the seal collar first and will not contact the seal lip (protecting delicate seals from damage).Installation:,Remove the screw and slide valais over the seatpost stanchion,Put the valais at the highest position, install the screw and tighten to 2-3 nm,Install your saddle bag with it as full as it will be on the trail.,Let all the air out of your frame shock, drop the post, and compress the bike suspension all the way.,Assure there is adequate tyre to saddlebag clearance. If there is not tyre clearance, raise the dropper, and lower the valais until there is adequate tyre to saddlebag clearance.,Re-inflate your shock and be sure that the valais is torqued to 2-3 nm.
The Wolf Tooth ReMote Dropper Lever is ergonomic, lightweight and easy to install. Utilising sealed cartridge bearings for a silky-smooth action and a low profile, textured lever machined to the highest quality, this is the ultimate dropper upgrade.Compatible with all cable actuated dropper posts, the ReMote Dropper Lever is simple to install, maintain and has been built to last. Every single detail of the ReMote is the result of a singular drive to eliminate all complaints found with stock dropper levers.In an industry first, the ReMote uses a 21mm sealed cartridge bearing for smooth operation and unparalleled modulation. A precision-machined cable path and custom clamping screw with captive washer won’t damage cables like more common set screws. As an added bonus, cables can be cut to length and crimped prior to securing.The ReMote lever sits close to the bar, minimizing the distance the thumb must be removed from the grip while reducing the likelihood of knee contact in technical terrain and adds a bit of extra length to overcome stiff dropper internals.Wolf Tooth's team have also included an innovative engineered failure point, allowing the lever to break away from its base in the event of a crash. Replacement axles are inexpensive and readily available, ensuring that you can spend more time on the trails and less time in the workshop.Compatibility:Compatible with all cable actuated dropper posts.,Works with dropper posts that (a) have the barrel end of the cable at the remote position and (b) those that have the barrel end at the seat post. ,If your post is not listed in the charts found in the image gallery, Wolf Tooth recommends measuring the pivot centre to end of your current lever. If it is greater than 52mm the Light Action will work best. If it is less than 52mm, the Standard ReMote will work best.,ReMote for Magura is compatible with the 2-bolt clamp SRAM brakes that do not feature Matchmaker X clamps.,ReMote for Hope is only compatible with Tech 3 brakes..Mounting Types:ReMote IS-AB for Shimano I-Spec A or B - Includes IS-AB hardware,ReMote IS-II for Shimano I-Spec II - includes IS-II hardware ,ReMote MM SRAM/Avid MatchMaker X - Includes the MatchMakerX hardware, which is a T-Nut and bolt that allows the ReMote MM to attach to the MatchMakerX clamp. You will need the MatchMakerX handlebar clamp, which we do not sell but can easily be purchased.,ReMote 22.2mm - includes hinged handlebar clamp for 22.2mm handlebars. All mountain bike handlebars are 22.2mm where your shift and brake levers attach even on 31.8mm handlebars. (31.8mm and 35mm handlebars just refer to the diameter where the stem clamps). Attach with 1-2nm max.,ReMote 31.8 is available for road bikes where the ReMote is mounted next to the stem,ReMote Magura for Magura brakes and some 2-bolt clamp SRAM brakes - Includes Magura hardware,ReMote Hope for Tech3 Hope Brakes - includes Hope hardware,ReMote IS-EV for Shimano I-Spec EV - includes IS-EV hardware.
Wolf Tooth Magura Light Action Remote Dropper LeverThis Light Action dropper seatpost lever is engineered to solve common dropper remote problems with its ergonomic, compact and sturdy design. This Light Action version aims to solve common dropper remote complaints with its compact, ergonomic and sturdy design. The ReMote Light Action Dropper Lever has a longer lever arm than the standard ReMote, reducing the actuation force required by a third and making it ideal for dropper posts with a harder pull or if you prefer a light actuation feel. This dropper seatpost lever is another option in Wolf Tooth's industry-leading ReMote line of dropper remotes. Every single detail of the ReMote Light Action is the result of a singular drive to eliminate all complaints found with stock dropper levers.Sealed Cartridge BearingIn an industry first, the ReMote uses a 21mm sealed cartridge bearing for smooth operation and unparalleled modulation. A precision-machined cable path and custom clamping screw with a captive washer won't damage cables like more common set screws. As an added bonus, cables can be cut to length and crimped prior to securing.The ReMote lever sits close to the bar, minimising the distance the thumb must be removed from the grip while reducing the likelihood of knee contact in technical terrain and adds a bit of extra length to overcome stiff dropper internals.Lightweight with Hassle-free InstallationWolf Tooth's team has also included an innovative engineered failure point, allowing the lever to break away from its base in the event of a crash. Replacement axles are inexpensive and readily available, ensuring that you can spend more time on the trails and less time in the workshop.Beginning with a long list of rider and mechanic requests, the Wolf Tooth team set out to address each and every one. Based on rider feedback and tailored to work with some posts' stiffer internal springs, the ReMote LA is also the choice for those with thumb injuries or reduced hand strength. From its hassle-free installation to smooth ball bearing action to the engineered failure point, the lightweight ReMote leads in every category.Features: Body Material: 6061 T6 Aluminium Axle Material: Delrin Use: Mountain Bike (MTB) Clamp Type: Magura Clamp Included: Yes Ergonomic Easy to Install Sealed cartridge bearings Textured lever Made in USATechnologies: UpFront cable fixing: The dropper cable is attached at the lever, making setup and adjustment quick and easy. Simply secure cable at seatpost using stock barrel or cable clamp and route to bar for a significant reduction in installation time and frustration. Large-diameter ball-bearing pivot: An industry first, the ReMote uses a massive 21mm sealed cartridge bearing for smooth operation and unparalleled modulation. Cable-kind clamp: A precision-machined cable path and custom clamping screw with captive washer won't damage cables like more common set screws. As an added bonus, cables can be cut to length and crimped prior to securing. Low-profile lever: The ReMote lever sits close to the bar, minimizing the distance the thumb must be removed from the grip while reducing the likelihood of knee contact in technical terrain and adds a bit of extra length to overcome stiff dropper internals. Integrated cable adjustment: The ReMote solidly-mounted barrel adjuster makes on-the-fly adjustments quick and easy while eliminating the rattles caused by common inline cable adjusters. Breakaway axle pivot: Crashes are bad, but expensive crashes are worse. That's why the ReMote features an engineered failure point, allowing the lever to break away from its base in the event of a crash. Replacement axles are inexpensive and readily available from Wolf Tooth. High-traction lever: A machined surface ensures that control is not lost, even in the worst of conditions. Broad compatibility: The ReMote has been tested and is recommended for use with many cable-actuated dropper posts. See the compatibility section below for details. Made in the USA: Wherever the capabilities exist, Wolf Tooth is committed to domestic manufacturing. From lever to packaging, 65% or more of each ReMote is made in the USA.Manufacturer's Part Number: WTREMOTELAMAGURABuy Wolf Tooth Components from Chain Reaction Cycles, the World's Largest Online Bike Store.
Wolf Tooth Magura Remote Dropper LeverThis dropper seatpost lever is developed for use with Magura brakes. Thanks to its robust 6061 T6 aluminium construction, it's tough and reliable as you tackle demanding mountain terrain conditions. Ergonomic and easy to install, this dropper lever makes it easy to change your seatpost positioning without having to stop your ride. Its sealed cartridge bearings and textured lever also make it a perfect choice for smooth and consistent operation in all weather and terrain conditions.Solve common dropper remote complaints with the compact, ergonomic and sturdy ReMote dropper lever.Beginning with a long list of rider and mechanic requests, the Wolf Tooth team set out to address each and every one. From its hassle-free installation, to smooth ball bearing action, to the engineered failure point, the lightweight ReMote leads in every category.Features: Body Material: 6061 T6 Aluminium Axle Material: Delrin Use: Mountain Bike (MTB) Clamp Type: Magura Clamp Included: Yes Ergonomic Easy to Install Sealed cartridge bearings Textured lever Made in USATechnologies: UpFront cable fixing: The dropper cable is attached at the lever, making setup and adjustment quick and easy. Simply secure cable at seatpost using stock barrel or cable clamp and route to bar for a significant reduction in installation time and frustration. Large-diameter ball-bearing pivot: An industry first, the ReMote uses a massive 21mm sealed cartridge bearing for smooth operation and unparalleled modulation. Cable-kind clamp: A precision-machined cable path and custom clamping screw with captive washer won't damage cables like more common set screws. As an added bonus, cables can be cut to length and crimped prior to securing. Low-profile lever: The ReMote lever sits close to the bar, minimizing the distance the thumb must be removed from the grip while reducing the likelihood of knee contact in technical terrain and adds a bit of extra length to overcome stiff dropper internals. Integrated cable adjustment: The ReMote solidly-mounted barrel adjuster makes on-the-fly adjustments quick and easy while eliminating the rattles caused by common inline cable adjusters. Breakaway axle pivot: Crashes are bad, but expensive crashes are worse. That's why the ReMote features an engineered failure point, allowing the lever to break away from its base in the event of a crash. Replacement axles are inexpensive and readily available from Wolf Tooth. High-traction lever: A machined surface ensures that control is not lost, even in the worst of conditions. Broad compatibility: The ReMote has been tested and is recommended for use with many cable-actuated dropper posts. See the compatibility section below for details. Made in the USA: Wherever the capabilities exist, Wolf Tooth is committed to domestic manufacturing. From lever to packaging, 65% or more of each ReMote is made in the USA.Manufacturer's Part Number: WTREMOTEMAGURABuy Wolf Tooth Components from Chain Reaction Cycles, the World's Largest Online Bike Store.