crankbrothers Eggbeater 1 Mountain Bike PedalsEngineered to tackle tough mountain bike trails, the Eggbeater 1 Mountain Bike Pedals from crankbrothers features a lightweight, durable stamped steel construction and a long-lasting Chromoly (CrMo) spindle for unrivalled performance.Features: Stamped steel body and inner wing with steel spindle add strength and stability without a weight penalty Low-profile design delivers a more powerful and efficient pedal stroke 6° of knee-saving float with a choice of a 15 or 20° release angle gives you a customized fit for the trail Delrin bushing inner and outer bearings Plastic end cap Brass cleat and mounting hardware included Body Material: Stamped SteelSpindle: Forged CrMo steelBody & Wings: Stamped steelSpring: 300 series stainless steelInner Bearing: BushingOuter Bearing: CartridgeCleats: Premium brass cleats includedRelease Angle: 15 or 20 degreesWeight: 290gBuy crankbrothers Components from Chain Reaction Cycles, the World's Largest Online Bike Store.
The design for the original crank brothers pedal began out of frustration. The founders of crank brothers, Carl and Frank, were tired of getting stuck in mud-covered pedals with no way in or out. They realised that existing pedals were too complicated It started with a simple question: what is the best way to attach a shoe to a crank? To answer this question, Carl and Frank created a system with only two moving parts hinging on a spring. This system became known as the eggbeater pedal, and later it was adapted into the candy pedal. A word on maintenance In order to keep your crank brothers pedals running smoothly, they recommend the following: clean pedals every 30 hours of riding remove the pedal body from the spindle and wipe it clean of any dirty grease apply fresh grease to the inside of the pedal before re-installing the spindle Pedal features: Excellent mud-shedding: the design is very open 4-sided entry: clip in on all 4 sides of the pedal, by pushing forward or pulling backwards on the Extremely lightweight: pedal design is very simple with only a few key parts Increased float: 6° of side-to-side rotational play. The float of the pedal allows for the rid Fit adjustment: crank brothers premium cleats can be adjusted for 10° release Customise the fit between your shoe and the pedal by using tread contact sleeves Crank brothers pedals are fully re-buildable for simple maintenance. There is a consistency in part When servicing this pedal, use the rebuild kit designed for level 1 & 2 pedals
The eggbeater's simple design gives the advantage of amazing mud shedding and 4 points of entry making it perfect for XC trail riding and cyclo cross. The crankbrothers eggbeater is an iconic pedal designed by Carl and Frank the original founders of crankbrothers they were tired of getting stuck in mud-covered pedals with no way in or out. They realised that existing pedals were too complicated….It started with a simple question: what is the best way to attach a shoe to a crank? To answer this question Carl and Frank created a system with only two moving parts hinging on a spring. This system became known as the eggbeater pedal and later it was adapted into the candy pedal. Cleat: Premium brass cleats included Shims: Included Release Angle: 15° to 20° Warranty: 2 years Weight: 286g per pair Spindle: Forged scm435 chromoly steel Body: stamped steel Wings: Stamped steel Spring: 300 series stainless steel Inner bearing: Bushing Outer bearing: Cartridge Maximum rider weight: No restrictions Colours: Silver/Black or Silver/Red As with the rest of the crankbrothers range the pedals are fully serviceable with a level 1 / 2 service kit (product code CRB-11729). Servicing is simple and does not require any specialist tools just a flat head screwdriver socket wrench and 8mm allen key to hold the pedal by the axle. We recommend that the pedal is cleaned and greased every 30 hours of riding and the bearings are inspected for wear.
Designed with a four-sided entry system, this professional level, titanium-made pairing gives a sturdy and secure performance, with their self-cleaning construction making sure mud and moisture build-up are kept at bay. Coming complete with brass cleats and mounting hardware, this hard-wearing pedal set is ideal for the rowdy mountain marauder.
crankbrothers Eggbeater 11 Ti MTB PedalsTake a sweet ride with the Eggbeater 11 Ti pedal. Weighing in at only 174g per pair, the 11 Ti features all titanium construction with Eggbeater's four-sided entry.The choice of mountain bike pros worldwide, these pedals shed mud like water off a duck. Super easy to service, making them an viable investment for seasons to come.Features: Titanium body, inner wing, sleeve and spindle for ultimate weight savings Low-profile design keeps the sole close to the spindle for a more powerful and efficient pedal stroke 6° of knee-saving float with a choice of a 15° or 20° release angle gives you a customized fit for all terrain 10mm needle bearing inner and cartridge bearing outer Brass cleat and mounting hardware included WEIGHT: 174g/pair Buy crankbrothers Components from Chain Reaction Cycles, the World's Largest Online Bike Store.
crankbrothers Eggbeater 2 MTB PedalsThe Eggbeater 2 pedal is slightly lighter than its brother the Eggbeater 3. Features Crank Brother's exclusive, four-sided entry, mud shedding design, and weight saving minimalism.Features: Cast stainless body and spring with steel spindle add strength and stability without a weight penalty Low-profile design delivers a more powerful and efficient pedal stroke 6° of knee-saving float with a choice of a 15 or 20° release angle gives you a customized fit for the trail Delrin bushing inner and cartridge bearing outer Plastic end caps Brass cleat and mounting hardware included Weight: 272g/pair Buy crankbrothers Components from Chain Reaction Cycles, the World's Largest Online Bike Store.
The design for the original crank brothers pedal began out of frustration. The founders of crank brothers, Carl and Frank, were tired of getting stuck in mud-covered pedals with no way in or out. They realised that existing pedals were too complicated It started with a simple question: what is the best way to attach a shoe to a crank? To answer this question, Carl and Frank created a system with only two moving parts hinging on a spring. This system became known as the eggbeater pedal, and later it was adapted into the candy pedal. A word on maintenance In order to keep your crank brothers pedals running smoothly, they recommend the following: clean pedals every 30 hours of ridingremove the pedal body from the spindle and wipe it clean of any dirty greaseapply fresh grease to the inside of the pedal before re-installing the spindle
crankbrothers Eggbeater 3 MTB Pedals - Electric BlueThe crankbrothers Eggbeater 3 MTB Pedals provide the superior mud shedding ability, customisability and ease-of-use of crankbrothers' four-sided entry clip mechanism in a beautifully minimal, seriously lightweight package.Features: Body Material: Cast Stainless Steel Spindle Material: Forged scm 435 CrMo Spring Material: 300 series Stainless Steel Wing Material: 17-4PH Stainless Steel End cap: Hex alloy Bearings: Inner: Igus LL-glide bearing; Outer: Enduro cartridge bearing Cleats: Premium Brass cleats with shims included Q-Factor: 52mm Release Angle: 15°/20° Minimal and lightweight Four-sided entry and superior mud shedding Customisable float & release angle Hex alloy end cap Premium bearings & double seal systemWeight: 280g per pairBuy crankbrothers Components from Chain Reaction Cycles, the World's Largest Online Bike Store.
Features: Minimal and lightweight Four-sided entry and superior mud shedding Customisable float & release angle Hex alloy end cap Premium bearings & double seal system
crankbrothers Eggbeater 3 MTB PedalsThe Eggbeater 3 pedal provides the form and function of Crank Brother's exclusive four-sided entry, at a price that allows you to outfit any bike.Features: Cast stainless body and spring with steel spindle add strength and stability without a weight penalty Low-profile design delivers a more powerful and efficient pedal stroke 6° of knee-saving float with a 10° release angle gives you a customised fit for the trail 10mm needle bearing inner and cartridge bearing outer Aluminium end cap Brass cleat and mounting hardware included Weight: 278g (pair)Buy crankbrothers Componentsfrom Chain Reaction Cycles, the World's Largest Online Bike Store.
The eggbeater's simple design gives the advantage of amazing mud shedding and 4 points of entry making it perfect for XC trail riding and cyclo cross. The crankbrothers eggbeater is an iconic pedal designed by Carl and Frank the original founders of crankbrothers they were tired of getting stuck in mud-covered pedals with no way in or out. They realised that existing pedals were too complicated….It started with a simple question: what is the best way to attach a shoe to a crank? To answer this question Carl and Frank created a system with only two moving parts hinging on a spring. This system became known as the eggbeater pedal and later it was adapted into the candy pedal. Cleat: Premium brass cleats included Shims: Included Release Angle: 15° to 20° Warranty: 5 years Weight: 278g per pair Spindle: Forged scm435 chromoly steel Body: cast stainless steel Wings: cast stainless steel Spring: 300 series stainless steel Inner bearing: Needle Outer bearing: Cartridge Maximum rider weight: No restrictions Colours options: Silver/Blue or Silver/Red You can customise the fit and feel of your pedal using crankbrothers tread contact sleeves (CRB-13282). They shims come with 3 different thicknesses enabling the rider to ensure good contact between their shoes and the pedal axle (as the tread wears down the contact can move away from the axle and onto the wings of the pedal). You may also like to run the pedals on your road / commuter bike. Buy a set of Quattro cleats (CRB-15289) to use on your road shoes. It makes pulling off from junctions a breeze as you have 4 points of entry to the pedals. As with the rest of the crankbrothers range the pedals are fully serviceable with a level 3 / 11 service kit (product code CRB-11730). Servicing is simple and does not require any specialist tools just a flat head screwdriver socket wrench and 8mm allen key to hold the pedal by the axle. We recommend that the pedal is cleaned and greased every 30 hours of riding and the bearings are inspected for wear.