Park Tool Crank Puller (CCP-22)With its long handle and the finely threaded head, the CCP-22 crank arm removal tool quickly attaches and gives you the advantage you need for removing stubborn crank arms. Park Tool has made it to be compatible with a wide range of models, making it ideal for home mechanics and professional mechanics alike.Features:Fits all cranks using 22mm x 1 threads and square, tapered bottom bracket spindles Also fits "Power Spline" cranks from SRAM using the 8mm thread bolt The strong rotating tip system ensures smooth operation and long lifeNOTE: For cranks using the ISIS Drive or Octalink system, look for the CCP-44 or the CWP-7 models.Buy Park Tool Workshop Tools from Chain Reaction Cycles, the World's Largest Online Bike Store.
Park Tool Crank Puller (CCP-44)With its long handle and fine thread to engage fully with compatible cranksets, the CCP-44 Crank Puller gives you the grip and control for removing even the most stubborn crank arms. Park Tool has made this easy to use pulling tool compatible with a wide range of Shimano Octalink and FSA ISIS Drive models.Features: Specifically designed to remove crank arms from splined Shimano® Octalink and ISIS Drive® bottom bracket spindles that do not use a "self-extracting" system22 x 1mm fine thread provides leverage needed to remove tight crank armsStrong rotating tip system ensures smooth operation and long life Not suitable for use with square taper type cranksetsBuy Park Tool Workshop from Chain Reaction Cycles, the World's Largest Online Bike Store.
Lightweight, minimal glove with exceptional fit and bar feel.Key Features:Low profile cuff is like wearing nothing at all,Lightweight back of hand materials for a close fit and exceptional breathability,Conductive Clarino® palm for touch screen compatibility,Polyamide Nylon 53%, Neoprene 13%, Polyurethane 11%,,Elastane 4%, Polyester 2%, Polyvinyl Chloride (PCV) 17%.
FR-2 Features: Fits older Sun Tour® two notch freewheels Two notches are approximately 25mm across measured outside to outside Always use a skewer or axle nut to hold remover firmly in place FR-4 Features: Fits Atom®, Regina®, splined Zeus®, and some Schwinn®-approved freewheels The FR-4 has 20 splines and is approximately 21.6mm in diameter Center bore for axle clearance is 10mm Always use a skewer or axle nut to hold tool firmly in place during removal FR-6 Features: Removes four-notch BMX / single-speed freewheel from hubs with 1.37 x 24 TPI threads The FR-6 has four notches approximately 32mm across measured inside to inside and 40mm outside to outside Fits over axles up to 16mm thread diameter Always use a skewer or axle nut to hold tool firmly in place during removal
Key Features: The Park tool 768 is a 43.8mm pilot for facing head tubes using the low profile Zero Stack type headset,The 768 is used with the 690-XL facer and the 750 centering cone adapter,Facing the head tube will improve the alignment of the bearings,The 768 pilot fits the Park tool HTR-1 Head tube Reamer and Facer Set.
The Park Tool CCP-44 is specifically designed to remove crank arms from splined Shimano® Octalink and ISIS Drive® bottom bracket spindles that do not use a self-extracting system.
What more could you want than pizza after a good day of wrenching or riding? An update of one of the all-time greats the PZT-2 Pizza Tool is bigger (for better hand position) better (super sharp large diameter stainless steel cutting wheel cuts through even the toughest terrain) and stronger! Amaze your friends show off to your in-laws; a bicycle and also a pizza cutter! Covered by Park Tool's legendary limited lifetime warranty
The Park Tool CCP-22 uses a long comfortable handle and extra fine thread that provides the needed leverage to remove even the tightest cranks. The unique "floating tip" ensures smooth operation and long life. As with most Park Tool products, it also features a hole specifically designed for hanging on a tool wall.
These Park Tool SD0, SD2, SD3, SD6 Screwdrivers are shop quality screwdrivers designed for comfort and durability. Featuring dual density grips and heat-treated, chrome vanadium tips and shafts.SD-0: No:0 Phillips SD-2: No: 2 PhillipsSD-3: 3mm flat bladeSD-6: 6mm flat blade
The Park Tool SPA6C uses hardened, replaceable pins. Designed for heavy-duty use, the distance between pins is adjustable, allowing use on virtually any hanger cup.
The Park Tool PP1 Hydraulic Brake Piston Press has a unique shape perfect for compressing the hydraulic piston by pushing the brake pads apart to speed up servicing and pad replacement. Slide the polished, wedge shaped tool between pads to expand the gap and pre-set the pistons into the caliper.
A selection of essential Torx wrenches in a convenient folding packageOne piece composite handle is comfortable lightweight and slip resistant - and 40% stronger than steelWrenches are made from high torque Bondhus Protanium industrial quality tool steel for a long lifeEasy to recognise on the work bench or tool box as this Torx set comes in green rather than the traditional Park blueThe T7 T9 T10 T15 T20 T25 T27 T30 and T40 Torx sizes supplied cover all the requirement of bikes todayTorx wrenches are becoming increasingly popular on Disc brakes and chainring bolts as they make it harder to round off bolts