Don't be fooled by the title, Enduro have been producing bearings since before the word "Enduro" became fashionable, there bearings are an industry leading design and they set the standard for all other bearing manufacturers to match. You may be more familiar with the ABEC standards from the worlds of skateboarding and roller blades but Enduro have tailored their bearings for the specific demands of cycling. The entry level industry standard of a bearing is ABEC 1 but Enduro do not produce any bearing which comes in at less than ABEC 3, this means that even if you choose an entry level Enduro bearing it is of better quality than another manufacturer's entry level bearing.These standard ABEC 3/5 bearings are designed for use within bottom brackets or hubs and give outstanding performance and longevity to your components.
Don't be fooled by the title, Enduro have been producing bearings since before the word "Enduro" became fashionable, there bearings are an industry leading design and they set the standard for all other bearing manufacturers to match. You may be more familiar with the ABEC standards from the worlds of skateboarding and roller blades but Enduro have tailored their bearings for the specific demands of cycling. The entry level industry standard of a bearing is ABEC 1 but Enduro do not produce any bearing which comes in at less than ABEC 3, this means that even if you choose an entry level Enduro bearing it is of better quality than another manufacturer's entry level bearing.These standard ABEC 3/5 bearings are designed for use within bottom brackets or hubs and give outstanding performance and longevity to your components.
The ABEC3 6804 LLU Max raises the bar for military standard, high precision bearings. This MAX model was engineered without retainers and 40% more balls than standard ABEC 3 or 5 bearings, enabling them to carry a much higher load and perfect for frame pivots. This bearing is packed with CRC Marine Grease, which will not wash out or break down when wet ensuring your frame bearings last longer than ever before. Technologies: LLU Seals: Two NBR 70 rubber seals with medium/high contact seal, which rides in a matching groove machined into the bearing to make a labyrinth type seal. The outer sealing lip repels dirt and water while the inner sealing lip retains the grease. CRC Sta-Plex Marine: This grease will not wash out or break down under any extreme conditions including power washing, salt water intrusion from the salted roads, or even dirt getting into the rolling areas. The High Pressure properties of this grease provides a cushion for the sharp blows that suspension pivots will endure. Tough and Tenacious for high impact and extreme conditions.
Enduro Bearings ABEC3 6804 LLU Max Bearing Optimised for use with cycling components, this MAX model has been built without retainers and contains 40% more balls than standard ABEC 3 or 5 bearings, enabling them to bear a far heavier load. Filled with CRC Marine Grease, a water-resistant and long-lasting performance is assured, especially when used with your frame pivots. Features: Dimensions: 20x32x7mm ABEC: 3 Grade: 10 Seals: LLU Grease: CRC-Marine Application: Frame Pivots Weight: 18.45g Buy Enduro Bearings Components from Chain Reaction Cycles, the World's Largest Online Bike Store.
Don't be fooled by the title, Enduro have been producing bearings since before the word "Enduro" became fashionable, there bearings are an industry leading design and they set the standard for all other bearing manufacturers to match. You may be more familiar with the ABEC standards from the worlds of skateboarding and roller blades but Enduro have tailored their bearings for the specific demands of cycling. The entry level industry standard of a bearing is ABEC 1 but Enduro do not produce any bearing which comes in at less than ABEC 3, this means that even if you choose an entry level Enduro bearing it is of better quality than another manufacturers entry level bearing.These standard ABEC3 MAX bearings are designed for use within linkages on full suspension frames, they have 40% more balls compared to standard ABEC3/5 bearings which gives unparalleled levels of smooth linkage movement when the frame is compressed.
Designed for use with the common 31.8mm bar thickness, you can install the Enduro stem in two ways. Run it in its standard upright position for a more relaxed ride, or flip it over and run it the other way for a more aggressive position. This lower option makes it ideal for use with modern MTB’s larger 27.5” or 29” wheels.
Unique Design The Enduroguard mudguard is an awesome front or rear mudguard. As a front mudguard it's amazing at stopping the mud and spray that’s thrown into your eyes from the back of the front wheel. Just snap off the round holes either side of the RRP logo and it becomes an effective rear mudguard protecting your linkages and shock from getting hammered. There is also a neat design feature of the “Seal Guard”, this enhanced bulge is specifically designed to give additional protection to your fork seals. Standard Size This Standard size is small enough to look right on short travel forks found on 4X and Cross Country/trail bikes, the fork brace is also usually closer to the stanchion so we have moved the holes for a more appropriate fit for smaller travel forks. Large Size This Large size offers great protection and is big enough to fit the longer travel forks found on Gravity Enduro and Downhill bikes, the fork brace on these forks are typically further away from the stanchions so we have moved the holes accordingly for a better fit. Usage The Enduroguard is designed as a front or rear mudguard and has been specifically adapted to do both jobs extremely well, the holes that are correct for fitting to the front forks do not work when using them to fit as a rear mudguard (unless the bike has a dropped rear brace), the snap off holes allows you to rotate the guard forward for better tyre clearance and protection. Clean with a hose or jet was, no chemicals are needed and may degrade the print over time. Seal Guard This additional bulge has been added and refined to offer additional protection for your seals against the relentless attack from spray and mud without affecting the fit or aesthetics, you will be grateful for this feature on those extremely wet rides prolonging the life of your fork seals. Front Mudguard The 'T' shape clamping points are designed to wrap around the fork leg providing a better and neater fit. The front of the mudguard is designed to offer slightly increased protection without spoiling the look of the mudguard. The wider curve with flat rear end offers maximum protection and frame clearance compared to a simple symmetrical curve. The main holes for the standard and the large are located in slightly different places, this reflects the typical differences between fork braces on long and short travel forks. Rear Mudguard The holes for the fork brace aren't ideally located when using it as a REAR mudguard, so there are 2 snap-off holes to allow you to rotate the guard forward and attach it to the brace between the rear stays (NB: The snap off holes are available on both the Standard and the Large sizes). This feature creates more mud/tyre clearance and a much better fit (although you can still use the main holes for the small number of bikes that have a dropped rear brace). Choose either the Standard or Large size depending on what rear protection you want to achieve (Standard would be the default size recommendation). Graphics Our product displays cool looking 2 tone screen printed graphics with our awesome Evil Eyes logo on the front to finish off the look nicely. Material RRP have taken a more expensive route opting for a custom thickness of polypropylene to meet their requirements, they felt the standard "off the shelf" options were either too thick (1.2mic) or too thin (0.8mic), their custom material sits squarely in-between. This offers the best of both worlds; the durability and quality feel that a thicker material gives, combined with the fit flexibility that a thinner material delivers. Zip Ties All sizes and colours will come with black coloured zip ties made to a custom length. Fitting Instructutions (also on sticker attached to rear of guard) Front 1) Remove the 4 zip ties supplied and insert them into all the holes as shown below 2) Bend and slide mudguard into position from the front 3) Loosely fasten up the top zip ties around the fork brace first then the legs 4) Centralise and then tighten up the top zip ties REAL tight so it won't move 5) Rotate the bottom zip ties until you get the desired angle and then tighten 6) Cut off any excess from the zip ties and rotate them out of the way Rear 1) Remove the snap-off holes either side of RRP logo as highlighted in red below 2) Loosely attach the zip ties to the rear stays and brace 3) Align to give you the correct tyre clearance 4) Now do up all the zip ties REAL tight
Designed to fit any fork, RapidRacerProducts has developed the EnduroGuard to work effectively with short-travel XC and 4X forks (80mm to 120mm travel). The 'T' shape clamping points on the arms are designed to wrap around the fork leg providing a better and neater fit. The front of the mudguard is designed to offer increased protection for higher speeds without spoiling the look of the mudguard. The wider curve with flat rear end offers maximum protection and frame clearance compared to a simple symmetrical curve. The holes for the fork brace aren't ideally located when using it as a rear mudguard, so these guards have two snap-off holes to allow you to rotate the guard forward and attach it to the brace between the rear stays, this feature creates more mud / tyre clearance and a much better fit.
Nukeproof Enduro StrapAs enduro riding becomes more challenging, so the need to carry spares securely and conveniently is vital. This durable and reliable strap by Nukeproof keeps your extra essentials firmly tethered to your bike instead of your back. Attaching your spares to your frame or saddle means you don't need to carry a bag or frees up or extra space in your bag for the likes of nutrition, gadgets and other must-haves. One strap will safely and comfortably hold a spare inner tube and two CO2 cannisters and is available in two lengths, 38cm for saddles and 60cm for frames.How to Use: 1. Get your spare tube and ensure that it is neatly folded. Gather any other accessories you want to carry (multi tool, CO2 etc) 2. Lay the strap flat, the side with the rubber grip area should be facing you 3. Place the inner tube on the strap and secure in place using the two loops 4. Turn the strap over 5. Get your accessories and push them between the strap & the tube 6. Take the loaded strap to your bike and set the rubber contact bars against the frame or saddle 7. Put the strap round the frame / saddle, though the loop and then back on itself, pull it tight and ensure the Velcro is securely in place 8. When mounting to your frame, ensure that the strap will not obstruct your shock or get in the way of other moving parts 9. On the 38cm strap there are extra Velcro securing tabs to go over the strap for added security, these can now be fastened 10. Go and enjoy your rideFeatures: Short: 38cm (For attaching to your saddle but can be used on frames with skinny tubing) Long: 60cm (For attaching to the frame but will also work on the saddle) Available in 6 Horizon ColourwaysBuy Nukeproof Accessories from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Enduro StrapAs enduro riding becomes more challenging, so the need to carry spares securely and conveniently is vital. This durable and reliable strap by Nukeproof keeps your extra essentials firmly tethered to your bike instead of your back. Attaching your spares to your frame or saddle means you don't need to carry a bag or frees up or extra space in your bag for the likes of nutrition, gadgets and other must-haves. One strap will safely and comfortably hold a spare inner tube and two CO2 cannisters and is available in two lengths, 38cm for saddles and 60cm for frames.How to Use: 1. Get your spare tube and ensure that it is neatly folded. Gather any other accessories you want to carry (multi tool, CO2 etc) 2. Lay the strap flat, the side with the rubber grip area should be facing you 3. Place the inner tube on the strap and secure in place using the two loops 4. Turn the strap over 5. Get your accessories and push them between the strap & the tube 6. Take the loaded strap to your bike and set the rubber contact bars against the frame or saddle 7. Put the strap round the frame / saddle, though the loop and then back on itself, pull it tight and ensure the Velcro is securely in place 8. When mounting to your frame, ensure that the strap will not obstruct your shock or get in the way of other moving parts 9. On the 38cm strap there are extra Velcro securing tabs to go over the strap for added security, these can now be fastened 10. Go and enjoy your rideFeatures: Short: 38cm (For attaching to your saddle but can be used on frames with skinny tubing) Long: 60cm (For attaching to the frame but will also work on the saddle) Available in 6 Horizon ColourwaysBuy Nukeproof Accessories from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Enduro StrapAs enduro riding becomes more challenging, so the need to carry spares securely and conveniently is vital. This durable and reliable strap by Nukeproof keeps your extra essentials firmly tethered to your bike instead of your back. Attaching your spares to your frame or saddle means you don't need to carry a bag or frees up or extra space in your bag for the likes of nutrition, gadgets and other must-haves. One strap will safely and comfortably hold a spare inner tube and two CO2 cannisters and is available in two lengths, 38cm for saddles and 60cm for frames.How to Use: 1. Get your spare tube and ensure that it is neatly folded. Gather any other accessories you want to carry (multi tool, CO2 etc) 2. Lay the strap flat, the side with the rubber grip area should be facing you 3. Place the inner tube on the strap and secure in place using the two loops 4. Turn the strap over 5. Get your accessories and push them between the strap & the tube 6. Take the loaded strap to your bike and set the rubber contact bars against the frame or saddle 7. Put the strap round the frame / saddle, though the loop and then back on itself, pull it tight and ensure the Velcro is securely in place 8. When mounting to your frame, ensure that the strap will not obstruct your shock or get in the way of other moving parts 9. On the 38cm strap there are extra Velcro securing tabs to go over the strap for added security, these can now be fastened 10. Go and enjoy your rideFeatures: Short: 38cm (For attaching to your saddle but can be used on frames with skinny tubing) Long: 60cm (For attaching to the frame but will also work on the saddle) Available in 6 Horizon ColourwaysBuy Nukeproof Accessories from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Enduro StrapAs enduro riding becomes more challenging, so the need to carry spares securely and conveniently is vital. This durable and reliable strap by Nukeproof keeps your extra essentials firmly tethered to your bike instead of your back. Attaching your spares to your frame or saddle means you don't need to carry a bag or frees up or extra space in your bag for the likes of nutrition, gadgets and other must-haves. One strap will safely and comfortably hold a spare inner tube and two CO2 cannisters and is available in two lengths, 38cm for saddles and 60cm for frames.How to Use: 1. Get your spare tube and ensure that it is neatly folded. Gather any other accessories you want to carry (multi tool, CO2 etc) 2. Lay the strap flat, the side with the rubber grip area should be facing you 3. Place the inner tube on the strap and secure in place using the two loops 4. Turn the strap over 5. Get your accessories and push them between the strap & the tube 6. Take the loaded strap to your bike and set the rubber contact bars against the frame or saddle 7. Put the strap round the frame / saddle, though the loop and then back on itself, pull it tight and ensure the Velcro is securely in place 8. When mounting to your frame, ensure that the strap will not obstruct your shock or get in the way of other moving parts 9. On the 38cm strap there are extra Velcro securing tabs to go over the strap for added security, these can now be fastened 10. Go and enjoy your rideFeatures: Short: 38cm (For attaching to your saddle but can be used on frames with skinny tubing) Long: 60cm (For attaching to the frame but will also work on the saddle) Available in 6 Horizon ColourwaysBuy Nukeproof Accessories from Chain Reaction Cycles, the World's Largest Online Bike Store.