Waterproof garments will, over time, lose some of the effectiveness of their water-repellent surface finishes. However, the Wash-in Rain Shield Re-Proofer (300ml) is an advanced Durable Water Repellent treatment that creates a new, tough barrier of weatherproof protection. Water will simply bead on the surface and roll off. And Rain Shield won't compromise the fabric's breathability either. Not only that, but it will also protect against mud and stains. It achieves all this protection while being safe for the environment, thanks to a water-based and PPCF-free formula. Protection is fully restored within 24 hours of treatment. Shake to Activate Use 100ml per large item (20 x 5ml caps) on a 30°C/86°F washing cycle for best results to help restore waterproofing performance on technical garments. How to: 1. Muc-Off recommends cleaning your technical apparel with their Technical Wash before treating with Wash-In Rain Sheild Re-Proofer for the best results. 2. Shake the bottle well to activate the formula. 3. For best results we recommend reproofing garments separately. 4. Use 20 x 5ml caps per large item, or two smaller items. Use 5 x capfuls if hand washing. 5. Pour the product directly into the detergent drawer of your washing machine 6. Wash on a full cycle at 30°C/86°F or according to the care label instructions. 7. Air-dry by hanging up and leave to dry overnight before wearing the garment in wet conditions again. Or tumble dry if the care label inside your garment permits. Top Tip For an even more durable treatment, you can apply our Rain Shield Re-Proofer spray as a second treatment after using the wash-in formula. This will build a secondary water-repellent coating on garments used in very harsh/wet conditions. N.B The efficiency of the DWR applied to the surface of the technical apparel will gradually wear off over time with normal wear and washing, so it's recommended to refresh the coating every 3 months depending on wear and washing frequency. All waterproof clothing needs to be cared for to keep it performing at its best. Using ordinary household detergent will ultimately break down the DWR and impair the water repellence, due to the heavy surfactants in these products. If you notice that water is no longer beading on the surface of your garment and soaking into the fabric, then it is time to refresh with Re-proofer.
The Face Fender XL is the new version of Mucky Nutz' Bender Fender but this version is pretty special as it is designed specifically for use on Fat Bikes. The biggest difference between this version and the standard MTB version is that is has 4 arms and split lines, this is to help the mudguard's extra length curve to give you added protection from mud, sand or snow. The 4 arms also provide the guard with added strength which it needs due to its slightly thicker build.Fits as close as possible to the knobbly bits for optimum 'muck' catching.Can be used on all wheel sizes.Protects your fork crown from getting caked.It's the lightest front Fat Bike mudguard available.Weight: 75g
Muc-Off Harsh Conditions Barrier uses a state-of-the-art, thin film coating to give your bike long term protection against rust and corrosion. It even works on surfaces that already have rust… it simply stops rust in its tracks, removing it altogether! Particularly effective in very harsh conditions, our formula is ideal for protecting your two-wheeled toy over the winter months when large amounts of road salts are out on the roads.The innovative new treatment drives out moisture, creating a durable anticorrosive all-weather barrier on your bike’s frame, chain, metal parts, plastics, and paintwork. Designed to continually penetrate corrosion, Muc-Off HarshConditions Barrier will spread into the tightest micro cracks and seams to remove moisture and salt-water. We’ve also added a UV application dye so you can check that every area you want to protect is treated and themaximum protection is always in place with a UV torch. Suitable for use on bicycles, ebikes and motorcycles.
Meet the brand new, fantastic, feature packed Face Fender!Lightweight, discreet, and very effective, the Face Fender is a simple front mud guard for mountain bikes, made from 100% recycled plastic.The HistoryThe Face Fender is the original ‘flexi-fender’ for Mountain Bikes, and the foundation on which we have built the Mucky Nutz empire!Introduced as the ‘Bender Fender’, way back in 2009 (yikes, we feel old!) our simple yet very effective mud guard was the first of its kind, taking the cycling community by storm.Today, 13 years after the original product was released, and with well over 1 million units sold world-wide, the Face Fender is more popular than ever. It has established itself as a household name, used and endorsed by Pro riders on the Downhill and Enduro circuits, and by weekend warriors alike!The DesignThe Face Fender design has been developed and refined several times over the years, to improve functionality and keep up with ever-changing suspension fork designs. We are very proud to bring you the latest and greatest Face Fender in this evolution.This edition brings a plethora of new features, offering you the highest functionality per gram, all within the most compact package possible. We are sticking with our tried and trusted (100% recycled) 1000 micron thickness material, which we have found to be the best balance between weight, flexibility, and durability.We are proud to be using 100% recycled plastic across the range, with re-useable VELCRO® Brand fasteners.Key Features· Stops muck, gravel, and ‘animal treats’ from being flung into your face, whilst thundering down the trail.· Simple design, which attaches to your suspension fork using the supplied VELCRO® Brand fasteners.· Super lightweight, at just 30g.· Compatible with 26", 27.5" and 29’’ wheel sizes.· Compatible with ‘standard’ and ‘boost’ suspension forks, with a forward-facing arch.· Will work with tyres up to 3’’ wide.· Improved seal shielding protects your precious (and expensive!) fork stanchions, seals and bridge from getting caked in mud and grit, reducing damage from wear and abrasion over time.· The new fold down front lip catches spray and splatter, keeping your face and eyes clear.· A secure fit, with no movement or rattling. You’ll hardly know it’s there.· Easy to clean, as it's flexible and opens flat. Spray it, wipe it, and you're done!· Comes with genuine, high-quality and super tough VELCRO® Brand fasteners. Velcro is soft on your paintwork, and makes fitting and removal a breeze for bike cleaning and maintenance.· Made in the UK, from 100% recycled waste plastic.Dimensions· Length: 241mm· Width: 272mm· Mass: 30gInstallation1. Break off the hanger tab, and remove the Velcro roll.2. Take the Velcro roll, and wrap it around a fork lower so it overlaps itself by an inch or so.3. Cut off that length, and repeat the process, so that you have two equal lengths.4. Do the same for the fork bridge. You will end up with two long lengths of Velcro for the lowers, and two short lengths for the bridge.5. Take the fender, and thread the long lengths of Velcro through the 'arm' holes (fluffy side towards the fork), and the short lengths through the two bridge holes.6. Position the fender to the underside of the fork bridge, and secure the top two Velcro straps around the bridge, pulling the fender up as high as possible.7. Now tighten the two fasteners around the fork lowers.8. Fold down the front lip, so that it clears the tyre by roughly 5 - 10mm.9. Square the fender up, and check tyre clearance.10. Go for a spin, and find some mud!SustainabilityIt's no secret that plastic is used in most of our products, and this is simply because it's the best material for the job. We manufacture everything using 100% recycled waste plastic.As a responsible manufacturer we are committed to sustainability; to produce and sell our products with minimal consumption, minimal packaging, and minimal waste.Each product is designed to serve its purpose over many years and is by no means a ‘single-use plastic’. When a Mucky Nutz product does eventually reach the end of its functional life, it can be fully recycled once more.
Muc-Off Waterless Wash is a highly advanced, easy to use spray which cleans and polishes in seconds without the need for water. It details your whole bike, motorcycle or car in seconds leaving behind a streak-free shine. Its innovative formula is designed to encapsulate any surface dirt to prevent scratching.Use it to remove light contaminants in between major washes.Key Features:Cleans and polishes in one application,No need for water!,Long lasts lustre,No residual dust or streaks,Non-sticky,Powder-free,Suitable to use on bicycles, motorcycles, cars & R.V's.
Using our state-of-the-art Nano Tech formula, Muc-Off cuts through grime quicker than you can say “OMG!” regardless of the weather or riding conditions. This classic pink Bike Cleaner has incredible cleaning power because it contains revolutionary Nano Technology that breaks down dirt and grime on microscopic levels, while also caring for your bike’s delicate finish. Because we use the finest ingredients and surfactants, our Muc-Off formula is a closely guarded trade secret.It’s the most effective cleaner out there, and it doesn’t even need any of those nasty, dangerous acids or chemicals. In fact, our perfectly pink cleaner is *biodegradable, free from acids, CFC’s and solvents, and it’s alkaline based so you can clean away with a guilt-free conscience. It’s safe on all surfaces, and it’s even disc brake rotor and pad friendly.Contains 2x 1L botttles,Safe on all parts and surfaces including carbon fibre,Will not harm seals, cables, brake pads or rotors,Safe on anodised metal,Alkaline based and free from CFCs, solvents or acids,Nano Tech Formula cleans on a molecular level,Biodegradable*.*Only contents are biodegradable.
The Muc-Off Rim tape is made from their own proprietary performance material with a pressure-sensitive adhesive to provide just the right amount stretch whilst maintaining the durability and strength needed to create a lasting airtight seal. Semi-transparent material makes locating the valve hole easy. Supplied with 4x Seal Patches. Available in a 10m and 50m workshop roll in 6 widths to suit most Road, CX, Gravel, MTB and Plus-sized rims.
The Muc-Off Rim tape is made from their own proprietary performance material with a pressure-sensitive adhesive to provide just the right amount stretch whilst maintaining the durability and strength needed to create a lasting airtight seal. Semi-transparent material makes locating the valve hole easy. Supplied with 4x Seal Patches. Available in a 10m and 50m workshop roll in 6 widths to suit most Road, CX, Gravel, MTB and Plus-sized rims.
When a puncture is simply too big to seal, the Muc-Off Puncture Plug Repair Kit is the ultimate backup tool that’s lightweight and easy-to-use. The tough and durable handle and 2-in-1 puncture plug/reamer tool comes with 5x thick plugs and 5x thin plugs packed all packed together in a handy storage pouch. Compatible with all tubeless road, MTB and gravel tyres. Refill packs with 10 repair plugs (5x thin and 5x thick) available separately.
The Muc-Off Rim tape is made from their own proprietary performance material with a pressure-sensitive adhesive to provide just the right amount stretch whilst maintaining the durability and strength needed to create a lasting airtight seal. Semi-transparent material makes locating the valve hole easy. Supplied with 4x Seal Patches. Available in a 10m and 50m workshop roll in 6 widths to suit most Road, CX, Gravel, MTB and Plus-sized rims.
The Muc-Off Rim tape is made from their own proprietary performance material with a pressure-sensitive adhesive to provide just the right amount stretch whilst maintaining the durability and strength needed to create a lasting airtight seal. Semi-transparent material makes locating the valve hole easy. Supplied with 4x Seal Patches. Available in a 10m and 50m workshop roll in 6 widths to suit most Road, CX, Gravel, MTB and Plus-sized rims.
Muc-Off Carbon GripperAfter many arduous trials and tests, Muc-Off's research and development team have managed to come up with the answer to the age old question of how to stop your carbon fixtures from slipping, Their highly advanced, all-new Carbon Gripper will quickly and easily increase carbon-on-carbon friction to keep your posts and bars as steady in their slots and holders as can be. Highly Efficient Carbon Assembly CompoundThis easy to apply pink paste features particles that increase 'mating friction' between carbon surfaces, as well as carbon-on-metal connections, giving superb grip to help keep your clamped carbon components from slipping and moving while your bike is in motion. With its holding capabilities reducing the amount of torque needed to secure seatposts and handlebars in place, the Carbon Gripper also prevents your fasteners from fracturing or becoming fatigued, improving and maintaining component life with every use. Muc-Off Carbon Gripper is the ideal solution to a slippery problem. Features: Keep Carbon parts gripped 'Non slip' surface to surface formula Specifically designed for Carbon Fibre parts Carbon Fibre safeBuy Muc-Off Accessories from Chain Reaction Cycles, the World's Largest Online Bike Store.