The Hope Technology Pro 4 Rear Hub Boost Conversion Kit is ideal for converting your existing Hope Pro 4 Hub or Hope Wheelset for use with frames with 148x12mm rear axle spacing. Incredibly easy to fit, the wheel will not require re-dishing once fitted, meaning you can hit the trails in no time.
Renew the pawls in your Pro 2 rear hub if they are a bit worn, for more positive engagement. Supplied as a set of four. Not including springs, please see associated products.
Assorted clear protection patches to protect your paintwork from cable rub, chain slap etc.
Introducing the Brand-X Ascend Dropper Seatpost shifter style lever kit. The ergonomic shifter style remote lever is designed to go where your front shifter would normally sit. This means that this kit is ideally suited for those using a 1x chain ring set up, without a front derailleur.Material: AL6061-T6Shimano I-Spec mount shifter style remote leverCable Length: 1.5mWeight: 40.7g (excluding cable)Adjustment: +10 degrees angle range and +7mm horizontal adjustmentFinish: Sand blasted and hard anodised blackWarranty: 2 Year
A simple essential kit for any riders running Tubeless tyres. The Lifeline Tubeless Repair Kit will get you up and riding again in no time. The kit contains 5 thick and 5 thin seals depending on the size of the tyre gash.Mark the area with the crayon, clean the hole with the reamer, fill the hole with the rubber adhesive, then insert your seal with the claw tool. Remove the claw tool and cut off the excess seal with the knife.Kit Includes:CrayonRubber SolutionReamer ToolClaw ToolKnife5 x Thick Tyre Seals5 x Thin Tyre Seals
The Brand-X Front Boost Conversion Kit allows for a 15x100mm hub to be converted to 15x110mm Boost spacing. This conversion kit includes two axle spacers, a 6-bolt rotor spacer and rotor bolts for straightforward installation. Designed to work with most 15mm non-Boost hubs, it is also recommended to check with your specific hub manufacturer for full compatibility. This kit is specifically developed to allow a 15x100mm hub to be converted to 15x110mm Boost spacing. Genuine Brand-X spare parts.Compatibility: Most 15mm non-Boost hubsIncludes: 2 x Axle spacers, 6-bolt rotor spacer and rotor boltsConversion: 15x100mm to 15x110mm
The Brand-X Rear Boost Conversion Kit allows for a 142x12mm hub to be converted to 148x12mm Boost spacing. This conversion kit includes two axle spacers, a 6-bolt rotor spacer and rotor bolts for straightforward installation. Designed to work with most 142mm non-Boost hubs, it is also recommended to check with your specific hub manufacturer for full compatibility. This kit is specifically developed to allow a 142x12mm hub to be converted to 148x12mm Boost spacing. Genuine Brand-X spare parts.Compatibility: Most 142mm non-Boost hubsIncludes: 2 x Axle spacers, 6-bolt rotor spacer and rotor boltsConversion: 142x12mm to 148x12mm
The Dynaplug Air Tubeless MTB Repair & Inflation Kit is an all in one tyre repair and reinflation solution and means that there is no faster way to get yourself back up and rolling.No need to remove the tyre, no messy glues or solvents, just plug and ride!Long MTB version designed to ensure the CO2 vents end up well inside the tyre, even past aggressive treads, for 35c or smaller road tyres please use our ROAD Air with a shorter insertion tubeA plug tail can be snipped off later if it bothers you; trim to about 4mm long depending on the locationCO2 can be dangerous, please read the instructions fully and wear gloves and eye protection, its also a good idea to give the Air system a try at home before you need to do it 'in the field'Kit features a precision machined air valve body, stainless steel repair nozzle/insertion tube, 4 x soft nose standard plugs and a storage pouchIn addition, there s an air hose for CO2 inflation if you just need to air up through the valve stemMade with pride in the USA using patented technology and warrantied for life under normal usageDynaplug is the fastest, easiest and all-round best way to repair a tubeless tyre mid-ride. When needed, just remove whatever caused the puncture, firmly push the novel insertion tube straight into the hole and extract the tool depositing the repair plug in the tyre, done! The Air system has an added twist. If a tyre has lost too much pressure, just discharge the CO2 cartridge to inflate the tyre before withdrawing the plug insertion tool, leaving you ready to go in seconds. The sealant-friendly repair plug is a unique viscoelastic impregnated rubber that bonds instantly and permanently with your tyre, and the nonabrasive brass tip will not scratch your rim or puncture your rim tape.
The Dynaplug Air Tubeless MTB Repair & Inflation Kit is an all in one tyre repair and reinflation solution and means that there is no faster way to get yourself back up and rolling.No need to remove the tyre, no messy glues or solvents, just plug and ride!Long MTB version designed to ensure the CO2 vents end up well inside the tyre, even past aggressive treads, for 35c or smaller road tyres please use our ROAD Air with a shorter insertion tubeA plug tail can be snipped off later if it bothers you; trim to about 4mm long depending on the locationCO2 can be dangerous, please read the instructions fully and wear gloves and eye protection, its also a good idea to give the Air system a try at home before you need to do it 'in the field'Kit features a precision machined air valve body, stainless steel repair nozzle/insertion tube, 4 x soft nose standard plugs and a storage pouchIn addition, there s an air hose for CO2 inflation if you just need to air up through the valve stemMade with pride in the USA using patented technology and warrantied for life under normal usageDynaplug is the fastest, easiest and all-round best way to repair a tubeless tyre mid-ride. When needed, just remove whatever caused the puncture, firmly push the novel insertion tube straight into the hole and extract the tool depositing the repair plug in the tyre, done! The Air system has an added twist. If a tyre has lost too much pressure, just discharge the CO2 cartridge to inflate the tyre before withdrawing the plug insertion tool, leaving you ready to go in seconds. The sealant-friendly repair plug is a unique viscoelastic impregnated rubber that bonds instantly and permanently with your tyre, and the nonabrasive brass tip will not scratch your rim or puncture your rim tape.
The Dynaplug Air Tubeless MTB Repair & Inflation Kit is an all in one tyre repair and reinflation solution and means that there is no faster way to get yourself back up and rolling.No need to remove the tyre, no messy glues or solvents, just plug and ride!Long MTB version designed to ensure the CO2 vents end up well inside the tyre, even past aggressive treads, for 35c or smaller road tyres please use our ROAD Air with a shorter insertion tubeA plug tail can be snipped off later if it bothers you; trim to about 4mm long depending on the locationCO2 can be dangerous, please read the instructions fully and wear gloves and eye protection, its also a good idea to give the Air system a try at home before you need to do it 'in the field'Kit features a precision machined air valve body, stainless steel repair nozzle/insertion tube, 4 x soft nose standard plugs and a storage pouchIn addition, there s an air hose for CO2 inflation if you just need to air up through the valve stemMade with pride in the USA using patented technology and warrantied for life under normal usageDynaplug is the fastest, easiest and all-round best way to repair a tubeless tyre mid-ride. When needed, just remove whatever caused the puncture, firmly push the novel insertion tube straight into the hole and extract the tool depositing the repair plug in the tyre, done! The Air system has an added twist. If a tyre has lost too much pressure, just discharge the CO2 cartridge to inflate the tyre before withdrawing the plug insertion tool, leaving you ready to go in seconds. The sealant-friendly repair plug is a unique viscoelastic impregnated rubber that bonds instantly and permanently with your tyre, and the nonabrasive brass tip will not scratch your rim or puncture your rim tape.
Want to be covered no matter what happens or just really, really hate walking home The Dynaplug Mega Pill is for all the truly prepared boy and girl scouts out there. The Mega pill is a perfectly machined, waterproof 6061 aluminium capsule that contains everything you need for epic rides in the middle of nowhere, including a grand total of 7 pre-loaded Dynaplug insertion tubes and a micro knife for cutting the plug tail.No need to remove the tyre, no messy glues or solvents, just plug and ride!If a single plug is not enough to seal a hole, just fold the tail flat on the tyre; hold it with your finger and stick another one in there!A plug tail can be snipped off later if it bothers you; trim to about 4mm long depending on the locationEven as the big boy of the Dynaplug range, the Mega pill is only 65 x 28 mm in size and weighs just 85 grams fully loadedKit includes the tool, 5 x standard and 2 x Megaplug compatible stainless-steel insertion tubes 5 x Soft nose standard plugs, 2 x Megaplugs, 1 x micro knife, a handy carry pouch and a pipe cleaner to help prep the tubes for reloadingMade with pride in the USA with patented technology and warrantied for life under normal usageDynaplug is the fastest, easiest and all-round best way to repair a tubeless tyre mid-ride. When needed, just remove whatever caused the puncture, firmly push the novel insertion tube straight into the hole and extract the tool depositing the repair plug in the tyre, done! The sealant-friendly repair plug is a unique viscoelastic impregnated rubber that bonds instantly and permanently with your tyre, and the nonabrasive brass tip will not scratch your rim or puncture your rim tape.
Want to be covered no matter what happens or just really, really hate walking home The Dynaplug Mega Pill is for all the truly prepared boy and girl scouts out there. The Mega pill is a perfectly machined, waterproof 6061 aluminium capsule that contains everything you need for epic rides in the middle of nowhere, including a grand total of 7 pre-loaded Dynaplug insertion tubes and a micro knife for cutting the plug tail.No need to remove the tyre, no messy glues or solvents, just plug and ride!If a single plug is not enough to seal a hole, just fold the tail flat on the tyre; hold it with your finger and stick another one in there!A plug tail can be snipped off later if it bothers you; trim to about 4mm long depending on the locationEven as the big boy of the Dynaplug range, the Mega pill is only 65 x 28 mm in size and weighs just 85 grams fully loadedKit includes the tool, 5 x standard and 2 x Megaplug compatible stainless-steel insertion tubes 5 x Soft nose standard plugs, 2 x Megaplugs, 1 x micro knife, a handy carry pouch and a pipe cleaner to help prep the tubes for reloadingMade with pride in the USA with patented technology and warrantied for life under normal usageDynaplug is the fastest, easiest and all-round best way to repair a tubeless tyre mid-ride. When needed, just remove whatever caused the puncture, firmly push the novel insertion tube straight into the hole and extract the tool depositing the repair plug in the tyre, done! The sealant-friendly repair plug is a unique viscoelastic impregnated rubber that bonds instantly and permanently with your tyre, and the nonabrasive brass tip will not scratch your rim or puncture your rim tape.