Genuine replacement E*Thirteen spare parts
A stiff engineering grade plastic support frame is co-molded to a softer more flexible material at the trailing edge for greater durability.
The Women's Short Sleeve Rash Vest is designed to be worn by water sports enthusiasts and beachgoers as a guard layer against the effects of harmful sun exposure to the skin and abrasion that can be caused by a wetsuit. Wearing this you are protected to a UPF 50 level whilst also looking great in or out of the water. It is constructed using soft handle fabrics that provide a flexible range of movement perfect for all watersports adventures. Recycled polyester Made by melting down existing plastic and re-spinning it into new fibres, recycled polyester production requires less energy and reduces CO2 emissions when compared to virgin polyester. Föhn uses Global Recycled Standard (GRS) certified rPET. GRS provides certification of recycled input, chain of custody, social and environmental practices, and use of hazardous chemicals during production. Care Instructions 30-degree machine wash, do not dry clean, do not bleach, do not tumble dry, low iron.
The RearGuard - OFF-ROAD is designed for use off-road on either a mountain bike or CX bike, it's a fast-fitting mudguard for those last-minute decisions. It attaches underneath the saddle with 1 velcro strap and takes less than 20 seconds to fit. It will never come off during your ride and offers great protection for your REAR and back. The 3 new creases add stability and strength and the additional length adds protection over rough terrain.
The Mankind Vision Nylon Front Hub Guards come in a pair, they fit and protect the Mankind Vision Front Hub and the Mankind Vision Front Wheel. Slide on Design.
Designed with a Muscle Support System, the Zone3 Calf Guards are built to reduce muscle vibration and improve shock absorption. Preventing injury, calf guards work to prevent muscle tears, cramping, shin splints and impact injuries. Post-exercise, you can expect quicker muscle repair and recovery times allowing you to train harder and reduce fatigue. Made from a high-wicking fabric, you can be sure to stay cool and dry and the 360-degree seamless construction eliminates chafing so you stay distraction-free and focused.
Replacement press fit plastic hub guards for Fiend cab front hub cone spacers. Sold as a pair.
This is the fourth generation of Ass Savers and is easily every user's best friend. Simple to install and weighing just 25.5 grammes Ass Savers Ass Saver Big is always there to cover your back. Ass Savers Ass Saver Big features the patent pending FLIP-TIP™ attachment system. Taking origami principles the FLIP-TIP™ system allows you to securely fasten the Ass Saver to the saddle with a simple flip of the tip and to unlock just flip the tip down and pull backwards. FLIP-TIP™ is compatible with all types of saddle rails including carbon rails. With the new generation of Ass Saver development has continued to reduce saddlebag interference. There is no guaranteed perfect fit but the Ass Saver Big is now a lot easier to install with a saddle bag than the previous models. Tech Spec: Measures: 383x115.5 mm Weight: 25.5 g Material: 0.8 mm PP (Polypropylene)
Unique Design The Enduroguard mudguard is an awesome front or rear mudguard. As a front mudguard it's amazing at stopping the mud and spray that’s thrown into your eyes from the back of the front wheel. Just snap off the round holes either side of the RRP logo and it becomes an effective rear mudguard protecting your linkages and shock from getting hammered. There is also a neat design feature of the “Seal Guard”, this enhanced bulge is specifically designed to give additional protection to your fork seals. Standard Size This Standard size is small enough to look right on short travel forks found on 4X and Cross Country/trail bikes, the fork brace is also usually closer to the stanchion so we have moved the holes for a more appropriate fit for smaller travel forks. Large Size This Large size offers great protection and is big enough to fit the longer travel forks found on Gravity Enduro and Downhill bikes, the fork brace on these forks are typically further away from the stanchions so we have moved the holes accordingly for a better fit. Usage The Enduroguard is designed as a front or rear mudguard and has been specifically adapted to do both jobs extremely well, the holes that are correct for fitting to the front forks do not work when using them to fit as a rear mudguard (unless the bike has a dropped rear brace), the snap off holes allows you to rotate the guard forward for better tyre clearance and protection. Clean with a hose or jet was, no chemicals are needed and may degrade the print over time. Seal Guard This additional bulge has been added and refined to offer additional protection for your seals against the relentless attack from spray and mud without affecting the fit or aesthetics, you will be grateful for this feature on those extremely wet rides prolonging the life of your fork seals. Front Mudguard The 'T' shape clamping points are designed to wrap around the fork leg providing a better and neater fit. The front of the mudguard is designed to offer slightly increased protection without spoiling the look of the mudguard. The wider curve with flat rear end offers maximum protection and frame clearance compared to a simple symmetrical curve. The main holes for the standard and the large are located in slightly different places, this reflects the typical differences between fork braces on long and short travel forks. Rear Mudguard The holes for the fork brace aren't ideally located when using it as a REAR mudguard, so there are 2 snap-off holes to allow you to rotate the guard forward and attach it to the brace between the rear stays (NB: The snap off holes are available on both the Standard and the Large sizes). This feature creates more mud/tyre clearance and a much better fit (although you can still use the main holes for the small number of bikes that have a dropped rear brace). Choose either the Standard or Large size depending on what rear protection you want to achieve (Standard would be the default size recommendation). Graphics Our product displays cool looking 2 tone screen printed graphics with our awesome Evil Eyes logo on the front to finish off the look nicely. Material RRP have taken a more expensive route opting for a custom thickness of polypropylene to meet their requirements, they felt the standard "off the shelf" options were either too thick (1.2mic) or too thin (0.8mic), their custom material sits squarely in-between. This offers the best of both worlds; the durability and quality feel that a thicker material gives, combined with the fit flexibility that a thinner material delivers. Zip Ties All sizes and colours will come with black coloured zip ties made to a custom length. Fitting Instructutions (also on sticker attached to rear of guard) Front 1) Remove the 4 zip ties supplied and insert them into all the holes as shown below 2) Bend and slide mudguard into position from the front 3) Loosely fasten up the top zip ties around the fork brace first then the legs 4) Centralise and then tighten up the top zip ties REAL tight so it won't move 5) Rotate the bottom zip ties until you get the desired angle and then tighten 6) Cut off any excess from the zip ties and rotate them out of the way Rear 1) Remove the snap-off holes either side of RRP logo as highlighted in red below 2) Loosely attach the zip ties to the rear stays and brace 3) Align to give you the correct tyre clearance 4) Now do up all the zip ties REAL tight
Each kit includes all the bolts and washers required to successfully rebuild your chain guide.
Designed to fit any fork, RapidRacerProducts has developed the EnduroGuard to work effectively with short-travel XC and 4X forks (80mm to 120mm travel). The 'T' shape clamping points on the arms are designed to wrap around the fork leg providing a better and neater fit. The front of the mudguard is designed to offer increased protection for higher speeds without spoiling the look of the mudguard. The wider curve with flat rear end offers maximum protection and frame clearance compared to a simple symmetrical curve. The holes for the fork brace aren't ideally located when using it as a rear mudguard, so these guards have two snap-off holes to allow you to rotate the guard forward and attach it to the brace between the rear stays, this feature creates more mud / tyre clearance and a much better fit.
The ProGuard Hook and Loop Straps from RapidRacerProducts are Hook and Loop straps to quickly attach and remove Proguard V2 mudguard to your bike.