Foaming Chain Cleaner is a real innovation in bike maintenance. Utilising Fenwick’s cleaning superiority, chain cleaning has never been so easy. Fenwick's Foaming Chain Cleaner makes chain cleaning part of your bike wash routine, instead of a laborious 2nd job that never gets done. With its simple mess free application, there is very little waste as only 5 to 10ml of product is needed per clean and it is biodegradable too. Foaming Chain Cleaner does not use solvents or acids (citrus) to be effective, resulting in a safe product to use. To make the process even easier just use the Chain Cleaning Sponge to scrub the chain and the Gear Brush to agitate the cassette, jockey wheels and chainset. The cleaner is biodegradable and safe to use on anodising, carbon, plastics, rubber and painted surfaces. Directions for use: 1) Place the chain in middle gear for ease of use 2) Whilst turning the crank spray Foaming Chain Cleaner directly on to chain 3) Leave to soak for a couple of minutes – this can be done whilst you clean the rest of the bike with Fenwick’s BIKE CLEANER 4) For best results run the chain through the Fenwick’s CHAIN CLEANING SPONGE, specifically designed to agitate and, importantly, capture the chain dirt for a cleaner clean 5) Rinse thoroughly with clean water Top tip: As a water soluble degreaser Foaming Chain Cleaner can be used on delicate parts
Unique Design The Enduroguard mudguard is an awesome front or rear mudguard. As a front mudguard it's amazing at stopping the mud and spray that’s thrown into your eyes from the back of the front wheel. Just snap off the round holes either side of the RRP logo and it becomes an effective rear mudguard protecting your linkages and shock from getting hammered. There is also a neat design feature of the “Seal Guard”, this enhanced bulge is specifically designed to give additional protection to your fork seals. Standard Size This Standard size is small enough to look right on short travel forks found on 4X and Cross Country/trail bikes, the fork brace is also usually closer to the stanchion so we have moved the holes for a more appropriate fit for smaller travel forks. Large Size This Large size offers great protection and is big enough to fit the longer travel forks found on Gravity Enduro and Downhill bikes, the fork brace on these forks are typically further away from the stanchions so we have moved the holes accordingly for a better fit. Usage The Enduroguard is designed as a front or rear mudguard and has been specifically adapted to do both jobs extremely well, the holes that are correct for fitting to the front forks do not work when using them to fit as a rear mudguard (unless the bike has a dropped rear brace), the snap off holes allows you to rotate the guard forward for better tyre clearance and protection. Clean with a hose or jet was, no chemicals are needed and may degrade the print over time. Seal Guard This additional bulge has been added and refined to offer additional protection for your seals against the relentless attack from spray and mud without affecting the fit or aesthetics, you will be grateful for this feature on those extremely wet rides prolonging the life of your fork seals. Front Mudguard The 'T' shape clamping points are designed to wrap around the fork leg providing a better and neater fit. The front of the mudguard is designed to offer slightly increased protection without spoiling the look of the mudguard. The wider curve with flat rear end offers maximum protection and frame clearance compared to a simple symmetrical curve. The main holes for the standard and the large are located in slightly different places, this reflects the typical differences between fork braces on long and short travel forks. Rear Mudguard The holes for the fork brace aren't ideally located when using it as a REAR mudguard, so there are 2 snap-off holes to allow you to rotate the guard forward and attach it to the brace between the rear stays (NB: The snap off holes are available on both the Standard and the Large sizes). This feature creates more mud/tyre clearance and a much better fit (although you can still use the main holes for the small number of bikes that have a dropped rear brace). Choose either the Standard or Large size depending on what rear protection you want to achieve (Standard would be the default size recommendation). Graphics Our product displays cool looking 2 tone screen printed graphics with our awesome Evil Eyes logo on the front to finish off the look nicely. Material RRP have taken a more expensive route opting for a custom thickness of polypropylene to meet their requirements, they felt the standard "off the shelf" options were either too thick (1.2mic) or too thin (0.8mic), their custom material sits squarely in-between. This offers the best of both worlds; the durability and quality feel that a thicker material gives, combined with the fit flexibility that a thinner material delivers. Zip Ties All sizes and colours will come with black coloured zip ties made to a custom length. Fitting Instructutions (also on sticker attached to rear of guard) Front 1) Remove the 4 zip ties supplied and insert them into all the holes as shown below 2) Bend and slide mudguard into position from the front 3) Loosely fasten up the top zip ties around the fork brace first then the legs 4) Centralise and then tighten up the top zip ties REAL tight so it won't move 5) Rotate the bottom zip ties until you get the desired angle and then tighten 6) Cut off any excess from the zip ties and rotate them out of the way Rear 1) Remove the snap-off holes either side of RRP logo as highlighted in red below 2) Loosely attach the zip ties to the rear stays and brace 3) Align to give you the correct tyre clearance 4) Now do up all the zip ties REAL tight
Environmentally friendly, easy to rinse off and highly effective, this degreaser will help you components to look and perform like new again.
Formulated to provide a professional clean in seconds, this high-quality bike cleaner removes grit and grease from chainrings, cassettes, chains and derailleurs. This means you will spend less time cleaning your bike and have more time in the saddle.
Designed to fit any fork, RapidRacerProducts has developed the EnduroGuard to work effectively with short-travel XC and 4X forks (80mm to 120mm travel). The 'T' shape clamping points on the arms are designed to wrap around the fork leg providing a better and neater fit. The front of the mudguard is designed to offer increased protection for higher speeds without spoiling the look of the mudguard. The wider curve with flat rear end offers maximum protection and frame clearance compared to a simple symmetrical curve. The holes for the fork brace aren't ideally located when using it as a rear mudguard, so these guards have two snap-off holes to allow you to rotate the guard forward and attach it to the brace between the rear stays, this feature creates more mud / tyre clearance and a much better fit.
This non-toxic formula is 100% biodegradable and is free from PTFE, Teflon and other harmful Petrochemicals, letting you take care of your bike without impacting the environment. Coming in a 200ml, recycled plastic bottle, it can be threaded onto most common grease guns for a mess-free and efficient application.
This easy to use and hassle-free cleaner features both a fan nozzle and an accurate pin nozzle, it's perfect for spraying larger areas and harder to reach places, such as your entire cassette or small derailleur hinges. This cleaner protects against contaminants and corrosion and leaves your drivetrain looking new after every maintenance session.
The ProGuard Hook and Loop Straps from RapidRacerProducts are Hook and Loop straps to quickly attach and remove Proguard V2 mudguard to your bike.
E-Bike Snow Foam has been developed by Tru-Tension for quick and easy cleaning, leaving a polished shimmering shine. Perfect for cleaning in a garage or shed without the need to rinse with water. Ideal for all E-Bikes, Road and MTB. Simply spray on Snow Foam and watch it instantly lift dirt from the surface. Wipe away without the need for water before buffing the surface clean. The perfect E-Bike cleaner. Our all-in-one instant action foam cleaner soaks into the dirt, lifting it away from the surface for an easy clean without the need for water. Once dry it leaves a polish which is buffed in to leave a high gloss finish. Perfect for cleaning indoors and without the need for water. Ideal for removing light dirt from frames and wheels. Safe to use on plastic and painted surfaces. Spray. Soak. Wipe. Buff. How to use your E-Bike Snow Foam Cleaner: Step 1: Spray onto frame, wheels or any painted, metal or plastic surfaces. Step 2: Leave for 5 – 30 seconds. The foam will go to work lifting the dirt and grime. Step 3: Wipe dirt away with a clean cloth. Step 4: Once dirt is removed, use a separate clean cloth (microfibre suggested) to buff the surface in circles to activate the polish, leaving a gleaming finish. Important: Do not use on braking components.
Directions: Get your bike wet Spray or brush Dirt Juice onto the bike and leave it to work its magic for no longer than 2 minutes, agitating the most stubborn areas with brush or sponge. If you prefer a bit more foaming action spray directly on to a brush and get to work with that. Rinse off with fresh water.
A Bike Cleaner for all Disciplines The Mobi Bike Cleaner Concentrate is designed for use on all surfaces, including all paintwork and clear coat finishes. So, whether you're clocking up winter miles on a road bike, tackling muddy cyclocross courses, or the worst trails, this Bike Cleaner Concentrate is ready to restore your bike to its former glory. Fast Acting Formula The fast acting formula will get to work straight away. Simply use one part concentrate to four parts water for the perfect strength bike cleaner. The formula penetrates dirt and grime to make light work of cleaning your bike.
Genuine, high-quality Mobi replacement.