The Thomson Elite seatpost is over 40% stronger on ultimate strength tests than the strongest production seatposts on the market.The Elite has double the fatigue life of any other production models tested. The tube and head of the Thomson seatpost are integral machined from one piece of high strength 7000 series Aluminium. The head is not pressed or bonded in. This allows for superior strength and minimum weight.7000 series Aluminium41mm Seat Rail grip lengthAvailable in 250mm, 330mm, 367mm and 410mm lengthsAvailable in all seatpost sizes-5° to +29° Tilt adjustment228g weight (330mm length)Certified to: EN 14766 2006 MTB and DIN CERTCO: 2006 MTBIt s incredibly lightweight, approximately 201g (250mm length) for road bikes and 228g (330mm length) for mountain bikes. The natural ellipse bore inside tube creates an optimum strength-to-weight ratio. We have a long 1.614 inch (41mm) seat rail grip length. This helps prevent seat rail bending from impact loads. Most other seatposts have grip lengths of at least 0.5 inch shorter than our grip length.The Thomson seatpost design incorporates a bending fuse to prevent catastrophic failure. All competitive seatposts tested, failed catastrophically with the seat and clamp components, sometimes pieces of the tube and head flew off in all directions.The Thomson seatpost has a clamp, head and upper tube strong enough to withstand 350 foot-lbs of torque. The tube will start to yield and bend at the seat tube clamp at about 250 foot-lbs of torque. Under severe impact the Thomson seatpost will bend slightly and allow the rider to come to a safe stop or finish the ride.The Thomson seatpost has all parts captive and can easily be attached to a seat without dis-assembly. Infinite tilt adjustment minus 5° and plus 29°. Very low profile clamps mean no seat interference as the swivel nuts are down between the seat rails. The designs and materials have passed extensive life and ultimate strength tests. Our ongoing testing program ensures that every production lot of seatposts meets Thomson standards. Impact absorbing clamps in the seatpost will spread and flex on impact to protect seat, rails, and rider. The seats survive heavy impact loads without bending the rails.
The Thomson Elite seatpost is over 40% stronger on ultimate strength tests than the strongest production seatposts on the market.The Elite has double the fatigue life of any other production models tested. The tube and head of the Thomson seatpost are integral machined from one piece of high strength 7000 series Aluminium. The head is not pressed or bonded in. This allows for superior strength and minimum weight.7000 series Aluminium41mm Seat Rail grip lengthAvailable in 250mm, 330mm, 367mm and 410mm lengthsAvailable in all seatpost sizes-5° to +29° Tilt adjustment228g weight (330mm length)Certified to: EN 14766 2006 MTB and DIN CERTCO: 2006 MTBIt s incredibly lightweight, approximately 201g (250mm length) for road bikes and 228g (330mm length) for mountain bikes. The natural ellipse bore inside tube creates an optimum strength-to-weight ratio. We have a long 1.614 inch (41mm) seat rail grip length. This helps prevent seat rail bending from impact loads. Most other seatposts have grip lengths of at least 0.5 inch shorter than our grip length.The Thomson seatpost design incorporates a bending fuse to prevent catastrophic failure. All competitive seatposts tested, failed catastrophically with the seat and clamp components, sometimes pieces of the tube and head flew off in all directions.The Thomson seatpost has a clamp, head and upper tube strong enough to withstand 350 foot-lbs of torque. The tube will start to yield and bend at the seat tube clamp at about 250 foot-lbs of torque. Under severe impact the Thomson seatpost will bend slightly and allow the rider to come to a safe stop or finish the ride.The Thomson seatpost has all parts captive and can easily be attached to a seat without dis-assembly. Infinite tilt adjustment minus 5° and plus 29°. Very low profile clamps mean no seat interference as the swivel nuts are down between the seat rails. The designs and materials have passed extensive life and ultimate strength tests. Our ongoing testing program ensures that every production lot of seatposts meets Thomson standards. Impact absorbing clamps in the seatpost will spread and flex on impact to protect seat, rails, and rider. The seats survive heavy impact loads without bending the rails.
The Thomson Elite seatpost is over 40% stronger on ultimate strength tests than the strongest production seatposts on the market.The Elite has double the fatigue life of any other production models tested. The tube and head of the Thomson seatpost are integral machined from one piece of high strength 7000 series Aluminium. The head is not pressed or bonded in. This allows for superior strength and minimum weight.7000 series Aluminium41mm Seat Rail grip lengthAvailable in 250mm, 330mm, 367mm and 410mm lengthsAvailable in all seatpost sizes-5° to +29° Tilt adjustment228g weight (330mm length)Certified to: EN 14766 2006 MTB and DIN CERTCO: 2006 MTBIt s incredibly lightweight, approximately 201g (250mm length) for road bikes and 228g (330mm length) for mountain bikes. The natural ellipse bore inside tube creates an optimum strength-to-weight ratio. We have a long 1.614 inch (41mm) seat rail grip length. This helps prevent seat rail bending from impact loads. Most other seatposts have grip lengths of at least 0.5 inch shorter than our grip length.The Thomson seatpost design incorporates a bending fuse to prevent catastrophic failure. All competitive seatposts tested, failed catastrophically with the seat and clamp components, sometimes pieces of the tube and head flew off in all directions.The Thomson seatpost has a clamp, head and upper tube strong enough to withstand 350 foot-lbs of torque. The tube will start to yield and bend at the seat tube clamp at about 250 foot-lbs of torque. Under severe impact the Thomson seatpost will bend slightly and allow the rider to come to a safe stop or finish the ride.The Thomson seatpost has all parts captive and can easily be attached to a seat without dis-assembly. Infinite tilt adjustment minus 5° and plus 29°. Very low profile clamps mean no seat interference as the swivel nuts are down between the seat rails. The designs and materials have passed extensive life and ultimate strength tests. Our ongoing testing program ensures that every production lot of seatposts meets Thomson standards. Impact absorbing clamps in the seatpost will spread and flex on impact to protect seat, rails, and rider. The seats survive heavy impact loads without bending the rails.
The Thomson Elite seatpost is over 40% stronger on ultimate strength tests than the strongest production seatposts on the market.The Elite has double the fatigue life of any other production models tested. The tube and head of the Thomson seatpost are integral machined from one piece of high strength 7000 series Aluminium. The head is not pressed or bonded in. This allows for superior strength and minimum weight.7000 series Aluminium41mm Seat Rail grip lengthAvailable in 250mm, 330mm, 367mm and 410mm lengthsAvailable in all seatpost sizes-5° to +29° Tilt adjustment228g weight (330mm length)Certified to: EN 14766 2006 MTB and DIN CERTCO: 2006 MTBIt s incredibly lightweight, approximately 201g (250mm length) for road bikes and 228g (330mm length) for mountain bikes. The natural ellipse bore inside tube creates an optimum strength-to-weight ratio. We have a long 1.614 inch (41mm) seat rail grip length. This helps prevent seat rail bending from impact loads. Most other seatposts have grip lengths of at least 0.5 inch shorter than our grip length.The Thomson seatpost design incorporates a bending fuse to prevent catastrophic failure. All competitive seatposts tested, failed catastrophically with the seat and clamp components, sometimes pieces of the tube and head flew off in all directions.The Thomson seatpost has a clamp, head and upper tube strong enough to withstand 350 foot-lbs of torque. The tube will start to yield and bend at the seat tube clamp at about 250 foot-lbs of torque. Under severe impact the Thomson seatpost will bend slightly and allow the rider to come to a safe stop or finish the ride.The Thomson seatpost has all parts captive and can easily be attached to a seat without dis-assembly. Infinite tilt adjustment minus 5° and plus 29°. Very low profile clamps mean no seat interference as the swivel nuts are down between the seat rails. The designs and materials have passed extensive life and ultimate strength tests. Our ongoing testing program ensures that every production lot of seatposts meets Thomson standards. Impact absorbing clamps in the seatpost will spread and flex on impact to protect seat, rails, and rider. The seats survive heavy impact loads without bending the rails.
The Thomson Elite seatpost is over 40% stronger on ultimate strength tests than the strongest production seatposts on the market.The Elite has double the fatigue life of any other production models tested. The tube and head of the Thomson seatpost are integral machined from one piece of high strength 7000 series Aluminium. The head is not pressed or bonded in. This allows for superior strength and minimum weight.7000 series Aluminium41mm Seat Rail grip lengthAvailable in 250mm, 330mm, 367mm and 410mm lengthsAvailable in all seatpost sizes-5° to +29° Tilt adjustment228g weight (330mm length)Certified to: EN 14766 2006 MTB and DIN CERTCO: 2006 MTBIt s incredibly lightweight, approximately 201g (250mm length) for road bikes and 228g (330mm length) for mountain bikes. The natural ellipse bore inside tube creates an optimum strength-to-weight ratio. We have a long 1.614 inch (41mm) seat rail grip length. This helps prevent seat rail bending from impact loads. Most other seatposts have grip lengths of at least 0.5 inch shorter than our grip length.The Thomson seatpost design incorporates a bending fuse to prevent catastrophic failure. All competitive seatposts tested, failed catastrophically with the seat and clamp components, sometimes pieces of the tube and head flew off in all directions.The Thomson seatpost has a clamp, head and upper tube strong enough to withstand 350 foot-lbs of torque. The tube will start to yield and bend at the seat tube clamp at about 250 foot-lbs of torque. Under severe impact the Thomson seatpost will bend slightly and allow the rider to come to a safe stop or finish the ride.The Thomson seatpost has all parts captive and can easily be attached to a seat without dis-assembly. Infinite tilt adjustment minus 5° and plus 29°. Very low profile clamps mean no seat interference as the swivel nuts are down between the seat rails. The designs and materials have passed extensive life and ultimate strength tests. Our ongoing testing program ensures that every production lot of seatposts meets Thomson standards. Impact absorbing clamps in the seatpost will spread and flex on impact to protect seat, rails, and rider. The seats survive heavy impact loads without bending the rails.
The Thomson Elite seatpost is over 40% stronger on ultimate strength tests than the strongest production seatposts on the market.The Elite has double the fatigue life of any other production models tested. The tube and head of the Thomson seatpost are integral machined from one piece of high strength 7000 series Aluminium. The head is not pressed or bonded in. This allows for superior strength and minimum weight.7000 series Aluminium41mm Seat Rail grip lengthAvailable in 250mm, 330mm, 367mm and 410mm lengthsAvailable in all seatpost sizes-5° to +29° Tilt adjustment228g weight (330mm length)Certified to: EN 14766 2006 MTB and DIN CERTCO: 2006 MTBIt s incredibly lightweight, approximately 201g (250mm length) for road bikes and 228g (330mm length) for mountain bikes. The natural ellipse bore inside tube creates an optimum strength-to-weight ratio. We have a long 1.614 inch (41mm) seat rail grip length. This helps prevent seat rail bending from impact loads. Most other seatposts have grip lengths of at least 0.5 inch shorter than our grip length.The Thomson seatpost design incorporates a bending fuse to prevent catastrophic failure. All competitive seatposts tested, failed catastrophically with the seat and clamp components, sometimes pieces of the tube and head flew off in all directions.The Thomson seatpost has a clamp, head and upper tube strong enough to withstand 350 foot-lbs of torque. The tube will start to yield and bend at the seat tube clamp at about 250 foot-lbs of torque. Under severe impact the Thomson seatpost will bend slightly and allow the rider to come to a safe stop or finish the ride.The Thomson seatpost has all parts captive and can easily be attached to a seat without dis-assembly. Infinite tilt adjustment minus 5° and plus 29°. Very low profile clamps mean no seat interference as the swivel nuts are down between the seat rails. The designs and materials have passed extensive life and ultimate strength tests. Our ongoing testing program ensures that every production lot of seatposts meets Thomson standards. Impact absorbing clamps in the seatpost will spread and flex on impact to protect seat, rails, and rider. The seats survive heavy impact loads without bending the rails.
The Masterpiece is over 40% stronger on ultimate strength tests than the strongest production seatposts on the market. Masterpiece posts weigh approximately 40g less than the same size Elite post. This weight reduction is accomplished while maintaining the strength and durability expected of a Thomson seatpost. Thomson accomplishes this weight reduction by machining the seatpost all over, including the oval inner diameter. It is able to hold closer tolerances by machining than by extrusion alone. Machining over an already beautiful design makes the Masterpiece Seatpost a work of art.Machined 7000 series Aluminium41mm seat rail grip lengthTilt adjustment from -5° to +29°Low profile clampsAvailable in 27.2mm, 30.9mm and 31.6mm diametersCertified to: EN 14766 2006 MTBThe tube and head of the Thomson Masterpiece seatpost is integral machined from one piece of high strength 7000 series aluminium. The head is not pressed or bonded in, allowing for superior strength and minimum weight.We have a long 1.614 inch (41 mm) seat rail grip length. This helps prevent seat rail bending from impact loads. Most other seatposts have grip lengths of at least 0.5 inches shorter than our grip length. The Thomson Masterpiece seatpost design incorporates a bending fuse to prevent catastrophic failure. All competitive seatposts we tested failed catastrophically with the seat and clamp components, sometimes pieces of the tube and head flew off in all directions.The Thomson Masterpiece seatpost has a clamp, head and upper tube strong enough to withstand 325 foot-lbs of torque. The tube will start to yield and bend at the seat tube clamp at about 230 foot-lbs of torque. Under severe impact the Thomson Masterpiece seatpost will bend slightly but allow the rider to come to a stop or continue the ride. The Masterpiece seatpost has all parts captive and can easily be attached to a seat without dis-assembly.Very low profile clamps mean no seat interference as the swivel nuts are down between the seat rails. The designs and materials have passed extensive life and ultimate strength tests. Our ongoing testing program ensures that every production lot of seatposts meets Thomson standards.
The Masterpiece is over 40% stronger on ultimate strength tests than the strongest production seatposts on the market. Masterpiece posts weigh approximately 40g less than the same size Elite post. This weight reduction is accomplished while maintaining the strength and durability expected of a Thomson seatpost. Thomson accomplishes this weight reduction by machining the seatpost all over, including the oval inner diameter. It is able to hold closer tolerances by machining than by extrusion alone. Machining over an already beautiful design makes the Masterpiece Seatpost a work of art.Machined 7000 series Aluminium41mm seat rail grip lengthTilt adjustment from -5° to +29°Low profile clampsAvailable in 27.2mm, 30.9mm and 31.6mm diametersCertified to: EN 14766 2006 MTBThe tube and head of the Thomson Masterpiece seatpost is integral machined from one piece of high strength 7000 series aluminium. The head is not pressed or bonded in, allowing for superior strength and minimum weight.We have a long 1.614 inch (41 mm) seat rail grip length. This helps prevent seat rail bending from impact loads. Most other seatposts have grip lengths of at least 0.5 inches shorter than our grip length. The Thomson Masterpiece seatpost design incorporates a bending fuse to prevent catastrophic failure. All competitive seatposts we tested failed catastrophically with the seat and clamp components, sometimes pieces of the tube and head flew off in all directions.The Thomson Masterpiece seatpost has a clamp, head and upper tube strong enough to withstand 325 foot-lbs of torque. The tube will start to yield and bend at the seat tube clamp at about 230 foot-lbs of torque. Under severe impact the Thomson Masterpiece seatpost will bend slightly but allow the rider to come to a stop or continue the ride. The Masterpiece seatpost has all parts captive and can easily be attached to a seat without dis-assembly.Very low profile clamps mean no seat interference as the swivel nuts are down between the seat rails. The designs and materials have passed extensive life and ultimate strength tests. Our ongoing testing program ensures that every production lot of seatposts meets Thomson standards.
The Masterpiece is over 40% stronger on ultimate strength tests than the strongest production seatposts on the market. Masterpiece posts weigh approximately 40g less than the same size Elite post. This weight reduction is accomplished while maintaining the strength and durability expected of a Thomson seatpost. Thomson accomplishes this weight reduction by machining the seatpost all over, including the oval inner diameter. It is able to hold closer tolerances by machining than by extrusion alone. Machining over an already beautiful design makes the Masterpiece Seatpost a work of art.Machined 7000 series Aluminium41mm seat rail grip lengthTilt adjustment from -5° to +29°Low profile clampsAvailable in 27.2mm, 30.9mm and 31.6mm diametersCertified to: EN 14766 2006 MTBThe tube and head of the Thomson Masterpiece seatpost is integral machined from one piece of high strength 7000 series aluminium. The head is not pressed or bonded in, allowing for superior strength and minimum weight.We have a long 1.614 inch (41 mm) seat rail grip length. This helps prevent seat rail bending from impact loads. Most other seatposts have grip lengths of at least 0.5 inches shorter than our grip length. The Thomson Masterpiece seatpost design incorporates a bending fuse to prevent catastrophic failure. All competitive seatposts we tested failed catastrophically with the seat and clamp components, sometimes pieces of the tube and head flew off in all directions.The Thomson Masterpiece seatpost has a clamp, head and upper tube strong enough to withstand 325 foot-lbs of torque. The tube will start to yield and bend at the seat tube clamp at about 230 foot-lbs of torque. Under severe impact the Thomson Masterpiece seatpost will bend slightly but allow the rider to come to a stop or continue the ride. The Masterpiece seatpost has all parts captive and can easily be attached to a seat without dis-assembly.Very low profile clamps mean no seat interference as the swivel nuts are down between the seat rails. The designs and materials have passed extensive life and ultimate strength tests. Our ongoing testing program ensures that every production lot of seatposts meets Thomson standards.
The Masterpiece is over 40% stronger on ultimate strength tests than the strongest production seatposts on the market. Masterpiece posts weigh approximately 40g less than the same size Elite post. This weight reduction is accomplished while maintaining the strength and durability expected of a Thomson seatpost. Thomson accomplishes this weight reduction by machining the seatpost all over, including the oval inner diameter. It is able to hold closer tolerances by machining than by extrusion alone. Machining over an already beautiful design makes the Masterpiece Seatpost a work of art.Machined 7000 series Aluminium41mm seat rail grip lengthTilt adjustment from -5° to +29°Low profile clampsAvailable in 27.2mm, 30.9mm and 31.6mm diametersCertified to: EN 14766 2006 MTBThe tube and head of the Thomson Masterpiece seatpost is integral machined from one piece of high strength 7000 series aluminium. The head is not pressed or bonded in, allowing for superior strength and minimum weight.We have a long 1.614 inch (41 mm) seat rail grip length. This helps prevent seat rail bending from impact loads. Most other seatposts have grip lengths of at least 0.5 inches shorter than our grip length. The Thomson Masterpiece seatpost design incorporates a bending fuse to prevent catastrophic failure. All competitive seatposts we tested failed catastrophically with the seat and clamp components, sometimes pieces of the tube and head flew off in all directions.The Thomson Masterpiece seatpost has a clamp, head and upper tube strong enough to withstand 325 foot-lbs of torque. The tube will start to yield and bend at the seat tube clamp at about 230 foot-lbs of torque. Under severe impact the Thomson Masterpiece seatpost will bend slightly but allow the rider to come to a stop or continue the ride. The Masterpiece seatpost has all parts captive and can easily be attached to a seat without dis-assembly.Very low profile clamps mean no seat interference as the swivel nuts are down between the seat rails. The designs and materials have passed extensive life and ultimate strength tests. Our ongoing testing program ensures that every production lot of seatposts meets Thomson standards.
The Masterpiece is over 40% stronger on ultimate strength tests than the strongest production seatposts on the market. Masterpiece posts weigh approximately 40g less than the same size Elite post. This weight reduction is accomplished while maintaining the strength and durability expected of a Thomson seatpost. Thomson accomplishes this weight reduction by machining the seatpost all over, including the oval inner diameter. It is able to hold closer tolerances by machining than by extrusion alone. Machining over an already beautiful design makes the Masterpiece Seatpost a work of art.Machined 7000 series Aluminium41mm seat rail grip lengthTilt adjustment from -5° to +29°Low profile clampsAvailable in 27.2mm, 30.9mm and 31.6mm diametersCertified to: EN 14766 2006 MTBThe tube and head of the Thomson Masterpiece seatpost is integral machined from one piece of high strength 7000 series aluminium. The head is not pressed or bonded in, allowing for superior strength and minimum weight. We have a long 1.614 inch (41mm) seat rail grip length. This helps prevent seat rail bending from impact loads. Most other seatposts have grip lengths of at least 0.5 inches shorter than our grip length.The Thomson Masterpiece seatpost design incorporates a bending fuse to prevent catastrophic failure. All competitive seatposts we tested failed catastrophically with the seat and clamp components, sometimes pieces of the tube and head flew off in all directions.The Thomson Masterpiece seatpost has a clamp, head, and upper tube strong enough to withstand 325 foot-lbs of torque. The tube will start to yield and bend at the seat tube clamp at about 230 foot-lbs of torque. Under severe impact the Thomson Masterpiece seatpost will bend slightly but allow the rider to come to a stop or continue the ride.The Masterpiece seatpost has all parts captive and can easily be attached to a seat without dis-assembly. Very low profile clamps means no seat interference as the swivel nuts are down between the seat rails. The designs and materials have passed extensive life and ultimate strength tests. Our ongoing testing program ensures that every production lot of seatposts meets Thomson standards.
The Masterpiece is over 40% stronger on ultimate strength tests than the strongest production seatposts on the market. Masterpiece posts weigh approximately 40g less than the same size Elite post. This weight reduction is accomplished while maintaining the strength and durability expected of a Thomson seatpost. Thomson accomplishes this weight reduction by machining the seatpost all over, including the oval inner diameter. It is able to hold closer tolerances by machining than by extrusion alone. Machining over an already beautiful design makes the Masterpiece Seatpost a work of art.Machined 7000 series Aluminium41mm seat rail grip lengthTilt adjustment from -5° to +29°Low profile clampsAvailable in 27.2mm, 30.9mm and 31.6mm diametersCertified to: EN 14766 2006 MTBThe tube and head of the Thomson Masterpiece seatpost is integral machined from one piece of high strength 7000 series aluminium. The head is not pressed or bonded in, allowing for superior strength and minimum weight. We have a long 1.614 inch (41mm) seat rail grip length. This helps prevent seat rail bending from impact loads. Most other seatposts have grip lengths of at least 0.5 inches shorter than our grip length.The Thomson Masterpiece seatpost design incorporates a bending fuse to prevent catastrophic failure. All competitive seatposts we tested failed catastrophically with the seat and clamp components, sometimes pieces of the tube and head flew off in all directions.The Thomson Masterpiece seatpost has a clamp, head, and upper tube strong enough to withstand 325 foot-lbs of torque. The tube will start to yield and bend at the seat tube clamp at about 230 foot-lbs of torque. Under severe impact the Thomson Masterpiece seatpost will bend slightly but allow the rider to come to a stop or continue the ride.The Masterpiece seatpost has all parts captive and can easily be attached to a seat without dis-assembly. Very low profile clamps means no seat interference as the swivel nuts are down between the seat rails. The designs and materials have passed extensive life and ultimate strength tests. Our ongoing testing program ensures that every production lot of seatposts meets Thomson standards.