Key Features:Genuine Shimano HollowTech II bottom bracket assemblyLength of screw thread is increased to enable the fitment of chain devicesSet includes left and right hand cups, spacers, inner cover, and inner O-ringsLight weight seal structure helps to remove vital gramsSealed cups keep out dirt and waterMaintenance freeCompatible with 68 mm and 73 mm shellDurable gold anodised finishEasy installation.
Splined bottom bracket for use with Shimano Octalink chainsets,Oversize BB spindle - large 22 mm diameter hollow cold forged chrome-moly pipe billet spindle reduces weight, increases strength and rigidity,Octalink splined axle/crank arm interface - results in more rigid crank assembly compared to square tapered spindle,Sealed cartridge assembly with oversize ball bearings - maintenance-free high efficiency rubber seals keep out dirt, mud, and water,Cartridge design allows easy installation without adjustment.
Press fit chrome steel BB90-95 cartridge bearings. Inner diameter of 24mm and outer diameter of 37mm. ,Spacers for adapting to BB95 included. ,Fits 90/95mm wide brackets. .
This bottom bracket will keep pedals insulated and turning smoothly. SRAM uses gutter seal technology that vastly improves sealing against the elements while reducing seal drag. The GXP system uses two bicycle-specific cartridge bearings and eight seals for a smooth and long lasting ride.A new standard in external bearing performance!Gutter Seal Technology Improved tool engagementSealed cartridge bearingsEnglish or Italian threads.
Wider PressFit 30 bottom bracket to accommodate wider bottom bracket specifications. PressFit 30 bottom bracket 68-92
A variant of the external bottom bracket, PressFit cut weight by up to 40 grams and give easier installation by allowing you to press the bearing cups into the frame instead of threading them. There's no change to the crank spindle length and diameter remain the same.PressFit cut weight by up to 40 grams and provide easier installation by allowing you to press the bearing cups into the frame instead of threading them.Theres no change to the crank spindle length and diameter are standard GXP (Red, Force, Rival, Apex)Compatibility: Truvativ GXP Cranksets.Weight 84g Caramic 94g standard..
Three, sealed cartridge style, bearings; two on the chainring side and one on the non-drive side.Weighs just 220 grams; only 30 grams more than Record.17 mm cro-moly steel, 102 mm hollow spindle fits 8, 9 and 10 speed Campy Record and Chorus cranks from 1995 to present.Unique taper is not interchangeable with Shimano.Removable cups are machined from 7000 series aluminum alloy and are easily replaceable.Comes with British (1.37 inches x 24 threads per inch) or larger diameter, Italian cups (36 mm x 24 threads per inch). Spindles are identical and always 102 mm long..
Three sealed cartridge style bearings; two on the chain ring side and one on the non-drive side.Fits all years and models of Daytona, Racing Triple, Centaur, Veloce and Mirage crank sets. Also fits 1993 and later Athena and pre-1995 Record and Chorus cranks.Will NOT fit older Campagnolo Nuovo or Super Record road cranks which require a 115 mm spindle with a 5 mm drive side offset. All newer Campy bottom brackets are symmetrical and lack any drive side offset.Comes in two threading configurations with spindle lengths of 111 or 115 mm. Weights listed below are for 111 mm spindles.Alloy cups and bearings are similar to Chorus and Record. The hollow cro-moly spindle is similar to the ACH bottom bracket spindle. 233 grams.Unique taper is not interchangeable with Shimano.Cups are machined from 7000 series aluminum alloy.Comes with British (1.37 inches x 24 threads per inch) or larger diameter, Italian cups (36 mm x 24 threads per inch). 16 mm, heat treated cro-moly, spindles are hollow and available in 111 or 115 mm lengths..
Key Features:The #752 is used to ream BB30 bottom bracket shells to an ID of 41.94 mm.,Must be used with the HTR-1 Head Tube Reaming and Facing Set with a QK750 Centring Cone Adaptor,
Features:The BBT-29 is a double-ended bottom bracket wrench designed to fit non-standard diameter 16-notch external bottom bracket bearing cups.One end fits cups with an outside diameter of 39 mm such as Shimano Dura-Ace 9000 series and XTR 980 series.The other fits 16-notch bearing cups with an outside diameter of 48.5 mm such as FSA MegaEvo.Made in the USA and covered by Park's legendary limited lifetime warranty.
External Bottom Bracket Nut RemoverFits External BB Cups.
Bottom Bracket Remover For Outboard Systems. Compatible with Shimano Hollowtech 2, Truvativ GXP, FSA MegaExo and RaceFace X-Type bottom brackets. Includes tool for Shimano non drive crank arm adjustment cap and also 15mm hex for Truvativ LH crank bolt as found on certain models.