Nukeproof Tubeless MTB Rim Tape (10m)This durable and dependable Nukeproof tubeless tape has been tested by its in-house team and athletes to ensure a firm and effective seal. Made to meet the demands of downhill and enduro racing, it does a sterling job in keeping your tubes protected as you take on the most daring descents and trails. One 10-metre roll will be enough tape to cater for 4x 29” wheels. One layer with a 4” overlap is all that is required to tape your wheel for tubeless setup. We recommend using a tape which is 2 - 3mm wider than your inner rim width Instructions for Use Remove any old tape and sealant residue Ensure rim is clean and dry Start opposite the valve hole and maintain tension as you apply tape Work air bubbles out as you tape the wheel (Push them out via the spoke holes) Apply one layer of tape with a 4" overlap Ensure all air bubbles have been removed and tape is fully stuck right out to the edges of the rim Pierce a small hole and insert your valveFeatures: Length: 10m Suitability: Downhill, Enduro Buy Nukeproof Wheels & Tyres from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Tubeless MTB Rim Tape (10m)This durable and dependable Nukeproof tubeless tape has been tested by its in-house team and athletes to ensure a firm and effective seal. Made to meet the demands of downhill and enduro racing, it does a sterling job in keeping your tubes protected as you take on the most daring descents and trails. One 10-metre roll will be enough tape to cater for 4x 29” wheels. One layer with a 4” overlap is all that is required to tape your wheel for tubeless setup. We recommend using a tape which is 2 - 3mm wider than your inner rim width Instructions for Use Remove any old tape and sealant residue Ensure rim is clean and dry Start opposite the valve hole and maintain tension as you apply tape Work air bubbles out as you tape the wheel (Push them out via the spoke holes) Apply one layer of tape with a 4" overlap Ensure all air bubbles have been removed and tape is fully stuck right out to the edges of the rim Pierce a small hole and insert your valveFeatures: Length: 10m Suitability: Downhill, Enduro Buy Nukeproof Wheels & Tyres from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Tubeless MTB Rim Tape (10m)This durable and dependable Nukeproof tubeless tape has been tested by its in-house team and athletes to ensure a firm and effective seal. Made to meet the demands of downhill and enduro racing, it does a sterling job in keeping your tubes protected as you take on the most daring descents and trails. One 10-metre roll will be enough tape to cater for 4x 29” wheels. One layer with a 4” overlap is all that is required to tape your wheel for tubeless setup. We recommend using a tape which is 2 - 3mm wider than your inner rim width Instructions for Use Remove any old tape and sealant residue Ensure rim is clean and dry Start opposite the valve hole and maintain tension as you apply tape Work air bubbles out as you tape the wheel (Push them out via the spoke holes) Apply one layer of tape with a 4" overlap Ensure all air bubbles have been removed and tape is fully stuck right out to the edges of the rim Pierce a small hole and insert your valveFeatures: Length: 10m Suitability: Downhill, Enduro Buy Nukeproof Wheels & Tyres from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Neutron V2 RimThis MTB rim has gone through extensive testing, so you can benefit from its fantastic strength and smooth rolling performance on the toughest of rides. It features a 28mm internal diameter and it's constructed from a 6066 alloy, which makes it light enough for aggressive trail-riding as well as strong enough for DH. This rim can be setup tubeless by using tubeless tape and is for disc brake use only. Rim Size ERD Approx Weight 27.5" 560.9 470g 29" 598.9 500g Features: Rim Material: 6066 Alloy Use: MTB Rim Inner Width: 28mm Rim External Width: 32mm Drilling: 32 hole Rim Height: 18mm Join: Welded Tubeless Compatible: Yes - use 33mm tape Brake Type: Disc only Finish: Sandblasted Valve Type: Presta Single or Pair: SingleBuy Nukeproof Wheels & Tyres from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Horizon V2 RimThis MTB rim is constructed from a special blend of alloys, which give it a similar hardness to 7-series alloy but with the ductility and yield properties of a 6-series. This means that you'll benefit from the best of both worlds as you blast across the mountain. Nukeproof has also equipped this model with a micro-shotpeened and anodised finish, which gives it an extra layer of resistance against corrosion and wear. As a result, you'll enjoy being able to shred the trails in all weather conditions, without worrying about the elements damaging your gear.Nukeproof has ensured that their front and rear rim profiles are the same but due to the rear rim being more likely to take most of the hits, they have used a thicker sidewall for added strength. The front rim has a thinner sidewall, which allows for excellent weight savings and a perfect balance between strength and weight. If you want some extra security, or if you want to save some more weight, there is no problem using a pair of front or rear rims. Option ERD Weight 27.5" Front 554.5 460g +/- 5% 27.5" Rear 554.3 490g +/- 5% 29" Front 592.5 510g +/- 5% 29" Rear 592.3 540g +/- 5% Features: Rim Material: Alloy Nukeproof BlendFinish: Micro shotpeened and anodised Use: MTB Rim Inner Width: 30mmRim Outer Width: 35mmRim Height: 21.6mmJoint: SleevedTubeless Compatible: Yes, Use 33mm tapeDrilling: 32 holeBrake Type: Disc onlyValve Type: PrestaBuy Nukeproof Wheels & Tyres from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Horizon V2 RimThis MTB rim is constructed from a special blend of alloys, which give it a similar hardness to 7-series alloy but with the ductility and yield properties of a 6-series. This means that you'll benefit from the best of both worlds as you blast across the mountain. Nukeproof has also equipped this model with a micro-shotpeened and anodised finish, which gives it an extra layer of resistance against corrosion and wear. As a result, you'll enjoy being able to shred the trails in all weather conditions, without worrying about the elements damaging your gear.Nukeproof has ensured that their front and rear rim profiles are the same but due to the rear rim being more likely to take most of the hits, they have used a thicker sidewall for added strength. The front rim has a thinner sidewall, which allows for excellent weight savings and a perfect balance between strength and weight. If you want some extra security, or if you want to save some more weight, there is no problem using a pair of front or rear rims. Option ERD Weight 27.5" Front 554.5 460g +/- 5% 27.5" Rear 554.3 490g +/- 5% 29" Front 592.5 510g +/- 5% 29" Rear 592.3 540g +/- 5% Features: Rim Material: Alloy Nukeproof BlendFinish: Micro shotpeened and anodised Use: MTB Rim Inner Width: 30mmRim Outer Width: 35mmRim Height: 21.6mmJoint: SleevedTubeless Compatible: Yes, Use 33mm tapeDrilling: 32 holeBrake Type: Disc onlyValve Type: PrestaBuy Nukeproof Wheels & Tyres from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Universal Presta Tubeless Valves (Pair)This pair of tubeless valves from Nukeproof have been created to be compatible with tubeless tyre inserts. These valves benefit from a removable core, ensuring you can get the most airflow from your pump or cartridge. The head of these valves has also been designed to sit on top, enabling easier inflation and deflation. The custom cap has been specially designed and has an integrated core remover for removing and tightening the core without any additional tools. The nut has also been designed so that you can get a good grip on the flat edges to firmly tighten the valve on the rim.An O-ring is included and sits against the outside of the rim to prevent damage to the rim.How to InstallRemove valve cap and nut, insert valve through rim, fit o-ring to valve then thread nut on and tighten by hand.Features:Valve Type: PrestaIncludes: Integrated valve core remover cap, O-ring, removable coreEasy installationSold as a pairWeight: 12g per pairBuy Nukeproof Wheels & Tyres from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Universal Presta Tubeless Valves (Pair)This pair of tubeless valves from Nukeproof have been created to be compatible with tubeless tyre inserts. These valves benefit from a removable core, ensuring you can get the most airflow from your pump or cartridge. The head of these valves has also been designed to sit on top, enabling easier inflation and deflation. The custom cap has been specially designed and has an integrated core remover for removing and tightening the core without any additional tools. The nut has also been designed so that you can get a good grip on the flat edges to firmly tighten the valve on the rim.An O-ring is included and sits against the outside of the rim to prevent damage to the rim.How to InstallRemove valve cap and nut, insert valve through rim, fit o-ring to valve then thread nut on and tighten by hand.Features:Valve Type: PrestaIncludes: Integrated valve core remover cap, O-ring, removable coreEasy installationSold as a pairWeight: 12g per pairBuy Nukeproof Wheels & Tyres from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Universal Presta Tubeless Valves (Pair)This pair of tubeless valves from Nukeproof have been created to be compatible with tubeless tyre inserts. These valves benefit from a removable core, ensuring you can get the most airflow from your pump or cartridge. The head of these valves has also been designed to sit on top, enabling easier inflation and deflation. The custom cap has been specially designed and has an integrated core remover for removing and tightening the core without any additional tools. The nut has also been designed so that you can get a good grip on the flat edges to firmly tighten the valve on the rim.An O-ring is included and sits against the outside of the rim to prevent damage to the rim.How to InstallRemove valve cap and nut, insert valve through rim, fit o-ring to valve then thread nut on and tighten by hand.Features:Valve Type: PrestaIncludes: Integrated valve core remover cap, O-ring, removable coreEasy installationSold as a pairWeight: 12g per pairBuy Nukeproof Wheels & Tyres from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Universal Presta Tubeless Valves (Pair)This pair of tubeless valves from Nukeproof have been created to be compatible with tubeless tyre inserts. These valves benefit from a removable core, ensuring you can get the most airflow from your pump or cartridge. The head of these valves has also been designed to sit on top, enabling easier inflation and deflation. The custom cap has been specially designed and has an integrated core remover for removing and tightening the core without any additional tools. The nut has also been designed so that you can get a good grip on the flat edges to firmly tighten the valve on the rim.An O-ring is included and sits against the outside of the rim to prevent damage to the rim.How to InstallRemove valve cap and nut, insert valve through rim, fit o-ring to valve then thread nut on and tighten by hand.Features:Valve Type: PrestaIncludes: Integrated valve core remover cap, O-ring, removable coreEasy installationSold as a pairWeight: 12g per pairBuy Nukeproof Wheels & Tyres from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Universal Presta Tubeless Valves (Pair)This pair of tubeless valves from Nukeproof have been created to be compatible with tubeless tyre inserts. These valves benefit from a removable core, ensuring you can get the most airflow from your pump or cartridge. The head of these valves has also been designed to sit on top, enabling easier inflation and deflation. The custom cap has been specially designed and has an integrated core remover for removing and tightening the core without any additional tools. The nut has also been designed so that you can get a good grip on the flat edges to firmly tighten the valve on the rim.An O-ring is included and sits against the outside of the rim to prevent damage to the rim.How to InstallRemove valve cap and nut, insert valve through rim, fit o-ring to valve then thread nut on and tighten by hand.Features:Valve Type: PrestaIncludes: Integrated valve core remover cap, O-ring, removable coreEasy installationSold as a pairWeight: 12g per pairBuy Nukeproof Wheels & Tyres from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Universal Presta Tubeless Valves (Pair)This pair of tubeless valves from Nukeproof have been created to be compatible with tubeless tyre inserts. These valves benefit from a removable core, ensuring you can get the most airflow from your pump or cartridge. The head of these valves has also been designed to sit on top, enabling easier inflation and deflation. The custom cap has been specially designed and has an integrated core remover for removing and tightening the core without any additional tools. The nut has also been designed so that you can get a good grip on the flat edges to firmly tighten the valve on the rim.An O-ring is included and sits against the outside of the rim to prevent damage to the rim.How to InstallRemove valve cap and nut, insert valve through rim, fit o-ring to valve then thread nut on and tighten by hand.Features:Valve Type: PrestaIncludes: Integrated valve core remover cap, O-ring, removable coreEasy installationSold as a pairWeight: 12g per pairBuy Nukeproof Wheels & Tyres from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Sam Hill Tubeless Valve Oil SlickThese durably made valves are perfect for efficient inflation as their adapted head allows your tyre insert to sit on top of the valve, with the shape of the head making it easy to inflate/deflate. Designed to be universal and works with tubeless tyre inserts, each valve has a removable core, which allows you to get maximum airflow from your tubeless pump or CO2 cartridge. These valves are in the special edition oil slick colourway, so you can enjoy their eye-catching finish that complements any ride.The custom cap has been specially designed and has an integrated core remover for removing and tightening the core without any additional tools. The nut has also been designed so that you can get a good grip on the flat edges to firmly tighten the valve on the rim.An O-ring is included and sits against the outside of the rim to prevent damage to the rim.How to InstallRemove valve cap and nut, insert valve through rim, fit o-ring to valve then thread nut on and tighten by hand.Features: Valve Type: Presta Includes: Integrated valve core remover cap, O-ring, removable core Easy installation Sold as a pair Weight: 12g per pairBuy Nukeproof Components from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Horizon Advanced Rim Defence - ARD PAIRThe Advanced Rim Defence (ARD) from MTB specialists Nukeproof has been developed to prevent damage to your rims and to stop punctures. Boasting a unique design, they have been developed over two years in collaboration with CRC sponsored downhill and enduro athletes and staff. During development, Nukeproof paid careful attention to the overall weight too, bringing a 29" insert at 144g and a 27.5” insert at 130g.Mountain Bike Rim ProtectorBy using closed cell foam technology, the A.R.D is a very lightweight tyre insert, yet it offers you lots of protection. It enables you to run your tyres at much lower pressures without risking flats, plus gives you much increased grip for thrashing around the trails. In fact, it's so good that Kelan Grant, a CRC-Mavic sponsored rider was able to complete a stage of the EWS on just his A.R.D as his tyre had split.MTB Tubeless Tyre Values IncludedIncluded in the box, you'll receive your A.R.D Inserts and two copper coloured tubeless valves. Specifically created for Nukeproof, these valves enable the quick inflation and deflation with the A.R.D installed in the wheel. Want to shorten ARD to fit in smaller wheels? Download a step by step guide here Features: Easy to fit and remove tyre Offers Pinch flat protection Offers Rim protection Will not absorb sealant Works with all rims which have an inner width from 19mm to 35mm Options: 27.5": Pair of 27.5" inserts; 29": Pair of 29" inserts; Mullet: 1x 27.5" insert & 1x 29" insert Weight: 130g per 27.5" insert, 144g per 29" insertPatent Pending 1804173.1Buy Nukeproof Accessories from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Horizon Advanced Rim Defence - ARD PAIRThe Advanced Rim Defence (ARD) from MTB specialists Nukeproof has been developed to prevent damage to your rims and to stop punctures. Boasting a unique design, they have been developed over two years in collaboration with CRC sponsored downhill and enduro athletes and staff. During development, Nukeproof paid careful attention to the overall weight too, bringing a 29" insert at 144g and a 27.5” insert at 130g.Mountain Bike Rim ProtectorBy using closed cell foam technology, the A.R.D is a very lightweight tyre insert, yet it offers you lots of protection. It enables you to run your tyres at much lower pressures without risking flats, plus gives you much increased grip for thrashing around the trails. In fact, it's so good that Kelan Grant, a CRC-Mavic sponsored rider was able to complete a stage of the EWS on just his A.R.D as his tyre had split.MTB Tubeless Tyre Values IncludedIncluded in the box, you'll receive your A.R.D Inserts and two copper coloured tubeless valves. Specifically created for Nukeproof, these valves enable the quick inflation and deflation with the A.R.D installed in the wheel. Want to shorten ARD to fit in smaller wheels? Download a step by step guide here Features: Easy to fit and remove tyre Offers Pinch flat protection Offers Rim protection Will not absorb sealant Works with all rims which have an inner width from 19mm to 35mm Options: 27.5": Pair of 27.5" inserts; 29": Pair of 29" inserts; Mullet: 1x 27.5" insert & 1x 29" insert Weight: 130g per 27.5" insert, 144g per 29" insertPatent Pending 1804173.1Buy Nukeproof Accessories from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Horizon Advanced Rim Defence - ARD PAIRThe Advanced Rim Defence (ARD) from MTB specialists Nukeproof has been developed to prevent damage to your rims and to stop punctures. Boasting a unique design, they have been developed over two years in collaboration with CRC sponsored downhill and enduro athletes and staff. During development, Nukeproof paid careful attention to the overall weight too, bringing a 29" insert at 144g and a 27.5” insert at 130g.Mountain Bike Rim ProtectorBy using closed cell foam technology, the A.R.D is a very lightweight tyre insert, yet it offers you lots of protection. It enables you to run your tyres at much lower pressures without risking flats, plus gives you much increased grip for thrashing around the trails. In fact, it's so good that Kelan Grant, a CRC-Mavic sponsored rider was able to complete a stage of the EWS on just his A.R.D as his tyre had split.MTB Tubeless Tyre Values IncludedIncluded in the box, you'll receive your A.R.D Inserts and two copper coloured tubeless valves. Specifically created for Nukeproof, these valves enable the quick inflation and deflation with the A.R.D installed in the wheel. Want to shorten ARD to fit in smaller wheels? Download a step by step guide here Features: Easy to fit and remove tyre Offers Pinch flat protection Offers Rim protection Will not absorb sealant Works with all rims which have an inner width from 19mm to 35mm Options: 27.5": Pair of 27.5" inserts; 29": Pair of 29" inserts; Mullet: 1x 27.5" insert & 1x 29" insert Weight: 130g per 27.5" insert, 144g per 29" insertPatent Pending 1804173.1Buy Nukeproof Accessories from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Neutron V2 Front WheelThis MTB front wheel has been completely redesigned from the ground up and gives riders incredibly fast and smooth rolling performance on every ride. It features a Nukeproof Neutron front hub that is available for both 15mm or 20mm spacings in both Boost and non-Boost. Nukeproof also sell end caps for QR (available separately).The 6066 alloy rim has been extensively to ensure it is a rim which is light enough for aggressive trail riding but strong enough for DH. Nukeproof have used J-Bend spokes meaning tensioning and spoke replacement is much simpler than using a straight pull spoke. The wheels come taped with tubeless valve installed so all you need to do is add sealant and your tyre to get a finished tubeless setup. The valve supplied is Nukeproofs Horizon valve which also has a core remover built into the cap. This valve is also compatible with tyre inserts like Nukeproof ARD. Spoke lengths on the front wheels are the same regardless of spacing, the length changes with wheel size: Wheel Wheel Size Non Driveside Spoke Length Driveside Spoke Length Front 27.5" 272 273 Front 29" 291 292 Conversion kits and replacement end caps available separately. Cap Nukeproof Part Number Usage Front 9mm QR NUKNEUV2F9QRCAPS Convert 15mm non boost hub to QR Not compatible with the 20mm non boost hub shell Front 15mm Caps NUKNEUV2F15CAPS Replacement 15mm end caps Not compatible with the 20mm hub shell Front 20mm Caps NUKNEUV2F20CAPS Replacement 20mm end caps Not compatible with the 15mm hub shell Front 15mm Rockshox Torque caps NUKNEUV2ENDB15T Convert 15mm boost hub for Rockshox Torque dropouts Front 20mm to 15mm boost conversion NUKNEUV2END2015B Convert 20mm boost hub to 15mm boost Front 20mm to 15mm non boost conversion NUKNEUV2END2015NB Convert 20mm non boost hub to 15mm non boost Full range of spare parts available. Features: Rim Material: 6066 Alloy Use: MTB, Trail, All Mountain, Enduro and DH Wheel Size: 27.5" or 29" options available Spacing Options: 15x100mm, 15x110mm, 20x110mm Non Boost, 20x110mm Boost Spoke Type: J-Bend Spoke Count: 32 Lacing Pattern: 3x Disc Mount: 6-bolt Inner Rim Width: 28mm External Rim Width: 32mm Rim Height: 18mm Tubeless Ready: Yes - Pre-taped and valve supplied Single or Pair: Single Build: Hand builtBuy Nukeproof Wheels & Tyres from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Neutron V2 Front WheelThis MTB front wheel has been completely redesigned from the ground up and gives riders incredibly fast and smooth rolling performance on every ride. It features a Nukeproof Neutron front hub that is available for both 15mm or 20mm spacings in both Boost and non-Boost. Nukeproof also sell end caps for QR (available separately).The 6066 alloy rim has been extensively to ensure it is a rim which is light enough for aggressive trail riding but strong enough for DH. Nukeproof have used J-Bend spokes meaning tensioning and spoke replacement is much simpler than using a straight pull spoke. The wheels come taped with tubeless valve installed so all you need to do is add sealant and your tyre to get a finished tubeless setup. The valve supplied is Nukeproofs Horizon valve which also has a core remover built into the cap. This valve is also compatible with tyre inserts like Nukeproof ARD. Spoke lengths on the front wheels are the same regardless of spacing, the length changes with wheel size: Wheel Wheel Size Non Driveside Spoke Length Driveside Spoke Length Front 27.5" 272 273 Front 29" 291 292 Conversion kits and replacement end caps available separately. Cap Nukeproof Part Number Usage Front 9mm QR NUKNEUV2F9QRCAPS Convert 15mm non boost hub to QR Not compatible with the 20mm non boost hub shell Front 15mm Caps NUKNEUV2F15CAPS Replacement 15mm end caps Not compatible with the 20mm hub shell Front 20mm Caps NUKNEUV2F20CAPS Replacement 20mm end caps Not compatible with the 15mm hub shell Front 15mm Rockshox Torque caps NUKNEUV2ENDB15T Convert 15mm boost hub for Rockshox Torque dropouts Front 20mm to 15mm boost conversion NUKNEUV2END2015B Convert 20mm boost hub to 15mm boost Front 20mm to 15mm non boost conversion NUKNEUV2END2015NB Convert 20mm non boost hub to 15mm non boost Full range of spare parts available. Features: Rim Material: 6066 Alloy Use: MTB, Trail, All Mountain, Enduro and DH Wheel Size: 27.5" or 29" options available Spacing Options: 15x100mm, 15x110mm, 20x110mm Non Boost, 20x110mm Boost Spoke Type: J-Bend Spoke Count: 32 Lacing Pattern: 3x Disc Mount: 6-bolt Inner Rim Width: 28mm External Rim Width: 32mm Rim Height: 18mm Tubeless Ready: Yes - Pre-taped and valve supplied Single or Pair: Single Build: Hand builtBuy Nukeproof Wheels & Tyres from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Neutron V2 Front WheelThis MTB front wheel has been completely redesigned from the ground up and gives riders incredibly fast and smooth rolling performance on every ride. It features a Nukeproof Neutron front hub that is available for both 15mm or 20mm spacings in both Boost and non-Boost. Nukeproof also sell end caps for QR (available separately).The 6066 alloy rim has been extensively to ensure it is a rim which is light enough for aggressive trail riding but strong enough for DH. Nukeproof have used J-Bend spokes meaning tensioning and spoke replacement is much simpler than using a straight pull spoke. The wheels come taped with tubeless valve installed so all you need to do is add sealant and your tyre to get a finished tubeless setup. The valve supplied is Nukeproofs Horizon valve which also has a core remover built into the cap. This valve is also compatible with tyre inserts like Nukeproof ARD. Spoke lengths on the front wheels are the same regardless of spacing, the length changes with wheel size: Wheel Wheel Size Non Driveside Spoke Length Driveside Spoke Length Front 27.5" 272 273 Front 29" 291 292 Conversion kits and replacement end caps available separately. Cap Nukeproof Part Number Usage Front 9mm QR NUKNEUV2F9QRCAPS Convert 15mm non boost hub to QR Not compatible with the 20mm non boost hub shell Front 15mm Caps NUKNEUV2F15CAPS Replacement 15mm end caps Not compatible with the 20mm hub shell Front 20mm Caps NUKNEUV2F20CAPS Replacement 20mm end caps Not compatible with the 15mm hub shell Front 15mm Rockshox Torque caps NUKNEUV2ENDB15T Convert 15mm boost hub for Rockshox Torque dropouts Front 20mm to 15mm boost conversion NUKNEUV2END2015B Convert 20mm boost hub to 15mm boost Front 20mm to 15mm non boost conversion NUKNEUV2END2015NB Convert 20mm non boost hub to 15mm non boost Full range of spare parts available. Features: Rim Material: 6066 Alloy Use: MTB, Trail, All Mountain, Enduro and DH Wheel Size: 27.5" or 29" options available Spacing Options: 15x100mm, 15x110mm, 20x110mm Non Boost, 20x110mm Boost Spoke Type: J-Bend Spoke Count: 32 Lacing Pattern: 3x Disc Mount: 6-bolt Inner Rim Width: 28mm External Rim Width: 32mm Rim Height: 18mm Tubeless Ready: Yes - Pre-taped and valve supplied Single or Pair: Single Build: Hand builtBuy Nukeproof Wheels & Tyres from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Neutron V2 Front WheelThis MTB front wheel has been completely redesigned from the ground up and gives riders incredibly fast and smooth rolling performance on every ride. It features a Nukeproof Neutron front hub that is available for both 15mm or 20mm spacings in both Boost and non-Boost. Nukeproof also sell end caps for QR (available separately).The 6066 alloy rim has been extensively to ensure it is a rim which is light enough for aggressive trail riding but strong enough for DH. Nukeproof have used J-Bend spokes meaning tensioning and spoke replacement is much simpler than using a straight pull spoke. The wheels come taped with tubeless valve installed so all you need to do is add sealant and your tyre to get a finished tubeless setup. The valve supplied is Nukeproofs Horizon valve which also has a core remover built into the cap. This valve is also compatible with tyre inserts like Nukeproof ARD. Spoke lengths on the front wheels are the same regardless of spacing, the length changes with wheel size: Wheel Wheel Size Non Driveside Spoke Length Driveside Spoke Length Front 27.5" 272 273 Front 29" 291 292 Conversion kits and replacement end caps available separately. Cap Nukeproof Part Number Usage Front 9mm QR NUKNEUV2F9QRCAPS Convert 15mm non boost hub to QR Not compatible with the 20mm non boost hub shell Front 15mm Caps NUKNEUV2F15CAPS Replacement 15mm end caps Not compatible with the 20mm hub shell Front 20mm Caps NUKNEUV2F20CAPS Replacement 20mm end caps Not compatible with the 15mm hub shell Front 15mm Rockshox Torque caps NUKNEUV2ENDB15T Convert 15mm boost hub for Rockshox Torque dropouts Front 20mm to 15mm boost conversion NUKNEUV2END2015B Convert 20mm boost hub to 15mm boost Front 20mm to 15mm non boost conversion NUKNEUV2END2015NB Convert 20mm non boost hub to 15mm non boost Full range of spare parts available. Features: Rim Material: 6066 Alloy Use: MTB, Trail, All Mountain, Enduro and DH Wheel Size: 27.5" or 29" options available Spacing Options: 15x100mm, 15x110mm, 20x110mm Non Boost, 20x110mm Boost Spoke Type: J-Bend Spoke Count: 32 Lacing Pattern: 3x Disc Mount: 6-bolt Inner Rim Width: 28mm External Rim Width: 32mm Rim Height: 18mm Tubeless Ready: Yes - Pre-taped and valve supplied Single or Pair: Single Build: Hand builtBuy Nukeproof Wheels & Tyres from Chain Reaction Cycles, the World's Largest Online Bike Store.