Nukeproof Tubeless MTB Rim Tape (10m)This durable and dependable Nukeproof tubeless tape has been tested by its in-house team and athletes to ensure a firm and effective seal. Made to meet the demands of downhill and enduro racing, it does a sterling job in keeping your tubes protected as you take on the most daring descents and trails. One 10-metre roll will be enough tape to cater for 4x 29” wheels. One layer with a 4” overlap is all that is required to tape your wheel for tubeless setup. We recommend using a tape which is 2 - 3mm wider than your inner rim width Instructions for Use Remove any old tape and sealant residue Ensure rim is clean and dry Start opposite the valve hole and maintain tension as you apply tape Work air bubbles out as you tape the wheel (Push them out via the spoke holes) Apply one layer of tape with a 4" overlap Ensure all air bubbles have been removed and tape is fully stuck right out to the edges of the rim Pierce a small hole and insert your valveFeatures: Length: 10m Suitability: Downhill, Enduro Buy Nukeproof Wheels & Tyres from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Low Direct Mount Upper MTB Chain GuideDesigned by the Nukeproof engineers for performance, this guide ensures that you don't drop your chain when out on the MTB trails. It features a hard-wearing alloy backplate with a composite top guide. This makes it more than capable of withstanding all the knocks and jolts as you blast across the mountain. Nukeproof has also equipped this trail-ready model with a soft rubber co-moulded into it. This also reduces wear and noise from your chain and increases its longevity. This guide fits all bikes with a SRAM S3 / Shimano E-Type front derailleur mount and comes with various washers allowing you to fine tune your chainline setup.Click here to download installation instructions.Features:Backplate Material: AlloyHardware Material: Stainless Steel Use: MTB Compatibility: 28-38T chainrings, Boost and Oval Weight: 32g (Guide, 2x bolts & 2x 3mm washers) Manufacturer Part Numbers:Copper: NPCHAGUILDMBlack: NPCHAGUILDMBLKBlue: NPCHAGUILDMBLUGrey: NPCHAGUILDMGRYPurple: NPCHAGUILDMPURRed: NPCHAGUILDMREDBuy Nukeproof Components from Chain Reaction Cycles, the World's Largest Online Bike Store.
Nukeproof Low Direct Mount Upper MTB Chain GuideDesigned by the Nukeproof engineers for performance, this guide ensures that you don't drop your chain when out on the MTB trails. It features a hard-wearing alloy backplate with a composite top guide. This makes it more than capable of withstanding all the knocks and jolts as you blast across the mountain. Nukeproof has also equipped this trail-ready model with a soft rubber co-moulded into it. This also reduces wear and noise from your chain and increases its longevity. This guide fits all bikes with a SRAM S3 / Shimano E-Type front derailleur mount and comes with various washers allowing you to fine tune your chainline setup.Click here to download installation instructions.Features:Backplate Material: AlloyHardware Material: Stainless Steel Use: MTB Compatibility: 28-38T chainrings, Boost and Oval Weight: 32g (Guide, 2x bolts & 2x 3mm washers) Manufacturer Part Numbers:Copper: NPCHAGUILDMBlack: NPCHAGUILDMBLKBlue: NPCHAGUILDMBLUGrey: NPCHAGUILDMGRYPurple: NPCHAGUILDMPURRed: NPCHAGUILDMREDBuy Nukeproof Components from Chain Reaction Cycles, the World's Largest Online Bike Store.
Made to meet the demands of downhill and enduro racing, it does a sterling job in keeping your tubes protected as you take on the most daring descents and trails. One 10-metre roll will be enough tape to cater for 4x 29” wheels. One layer with a 4” overlap is all that is required to tape your wheel for tubeless setup. We recommend using a tape which is 2 – 3mm wider than your inner rim width. Instructions for Use Remove any old tape and sealant residue Ensure rim is clean and dry Start opposite the valve hole and maintain tension as you apply tape Work air bubbles out as you tape the wheel (Push them out via the spoke holes) Apply one layer of tape with a 4" overlap Ensure all air bubbles have been removed and tape is fully stuck right out to the edges of the rim Pierce a small hole and insert your valve
This low direct mount guide features a hard-wearing alloy backplate with a composite top guide. This makes it perfect at handling all the knocks and jolts as you weave between the trails. Nukeproof has also equipped this trail-ready model with a soft rubber co-moulded into it. This also reduces wear and noise from your chain and increases its longevity. This guide fits all bikes with a SRAM S3 / Shimano E-Type front derailleur mount and comes with various washers allowing you to fine tune your chainline setup. Download installation instructions here Manufacturer Part Numbers: Copper: NPCHAGUILDM Black: NPCHAGUILDMBLK Blue: NPCHAGUILDMBLU Grey: NPCHAGUILDMGRY Purple: NPCHAGUILDMPUR Red: NPCHAGUILDMRED
This Nukeproof Bearing Kit is a genuine, high-quality replacement bearing kit, featuring high quality EZO Japanese cartridge bearings for Nukeproof Horizon front hubs.
Pack of Replacement removable ‘X’ cable guides for the Nukeproof Mega AM and TR.
Nukeproof Mega AM-TR X MTB Cable Guide PackPack of Replacement removable ‘X’ cable guides for the Nukeproof Mega AM and TR.Features:4x Triple Cable Guides and bolts2x Double Cable Guides and bolts2x Single Cable Guides and boltsCompatible with the Nukeproof Mega AM and TR FramesBuy Nukeproof Frame Spares from Chain Reaction Cycles, the World's Largest Online Bike Store.
The Nukeproof Element knurled grip has a thicker custom specified soft-compound Kraton rubber grip with a knurled pattern for optimum riding confidence and control.Featuring CNC-machined 7000-series aluminium lock-rings for wet-weather peace of mind and available in black, white or yellow, the Element is a comfortable and confidence-inspiring grip designed for hard riding in real-world conditions.Key Features:Soft custom Kraton rubber compound for maximum grip,Thicker design to dampen vibrations and increase comfort when riding,Includes CNC'd alloy lock-on collars.
This durable and dependable Nukeproof tubeless tape has been tested by its in-house team and athletes to ensure a firm and effective seal. Made to meet the demands of downhill and enduro racing, it does a sterling job in keeping your tubes protected as you take on the most daring descents and trails.One 10-metre roll will be enough tape to cater for 4x 29” wheels. One layer with a 4” overlap is all that is required to tape your wheel for tubeless setup. Instructions for Use: Remove any old tape and sealant residue,Ensure rim is clean and dry,Start opposite the valve hole and maintain tension as you apply tape,Work air bubbles out as you tape the wheel (Push them out via the spoke holes),Apply one layer of tape with a 4" overlap,Ensure all air bubbles have been removed and tape is fully stuck right out to the edges of the rim,Pierce a small hole and insert your valve,.Features:Length: 10mSuitability: Downhill, Enduro
Nukeproof Digger Hanger (2022)This rear mech hanger is specifically designed for use with Nukeproof Digger 2022 frames. Whether you're replacing your original rear derailleur hanger or simply keeping one as a spare, this replacement is ideal for getting your mountain bike up and running again.Features: Use: Mountain Bike (MTB) Compatibility: Nukeproof Digger (2022) Genuine Nukeproof spare partBuy Nukeproof Components from Chain Reaction Cycles, the World's Largest Online Bike Store.
Fully designed and developed by Nukeproof's in-house engineers, this mountain bike (MTB) seat clamp ensures a no compromise, reliable and lightweight design that's also an aesthetically pleasing finishing component for your bike. It features a CNC-machined 6061 aluminium build, which removes all unnecessary material so you can benefit from a super lightweight clamp without compromising strength.A CNC stainless steel barrel, stainless steel bolt, anodised finish and laser etched graphics ensure your clamp will stay fresh and hold your seatpost securely.The clamp is a universal design but has been designed to fit perfectly with Nukeproof frames to ensure a seamless gap-free fit between the clamp and the frame.
For their Neutron Half Waffle Lock On Grips, Nukeproof has adopted a race proven shape with an MX inspired half waffle grip pattern. Also, by using a low profile and a soft rubber compound, Nukeproof ensured that these grips offer optimised trail feedback without compromising on comfort. The locking mechanisms on either end provide a secure connection with the bar and the durable A25 Kraton rubber not only offers excellent grip, it ensures a long lifespan.Key Features:Material: A25 Kraton Soft Rubber Compound,Dual locking mechanisms,Low profile,Length: 142mm,Outer Diameter: 31mm,Built For: Trail, all-mountain, enduro, downhill, freeride,Weight: 110g (pair).
This replacement top guide is specifically engineered for use with Nukeproof chain guides. All set for rowdy and rebellious off-road adventures, this fantastic version features a polymide construction which makes it perfect at withstanding all the intensity that comes with all-day epics in the mountains. Please note: Bolts are not supplied with this model. Replacement bolt kits are available separately. Key Features: Material: Polymide,Use: MTB,Compatibility: Nukeproof chain guides.
A genuine replacement headset bearing from Nukeproof. This bearing has Ti coated races and Grade 10 Stainless steel balls.The bearing is ABEC 5 certified which means that it has passed tests which include ID and OD tolerance’s, roundness of ball, trueness of faces & surfaces aswell as noise testing at high RPM. These bearings have been designed and tested for the harshest of UK winters so if you want bearings that won’t let you down then these are the ones to get. Works with all Nukeproof headsets from 2015 onwards. Key Features: 1 1/8" Bearing: Replacement for all 1 1/8th Nukeproof headsets (Top Cups: T1 and T2, Bottom Cups B1-B4),Fits Nukeproof 1 1/8" headset cups for 1 1/8" steerer,Dimensions: 41.0 x 45 x 45mm,. 1.5"Bearing: Replacement for 1.5" Nukeproof headsets (2015 onwards Top Cup T3, Bottom Cup B5- B8),Fits Nukeproof 1.5" headset cups for 1.5" steerer,Dimensions: 51.8 x 45 x 45mm.
Created using soft and comfortable Kraton rubber, Nukeproof's Urchin grips are the ideal way to finish off your kid's cockpit. They're specially designed for small hands and ensure young shredders can ride with comfort and control as they attack the trails.The grips are 115mm long which is the perfect length for small hands and there is a flange on inner clamp for additional comfort and protection. The outer end is soft rubber to protect the rider and also the handlebar in the event of a crash.
Tried and tested by the Nukeproof team's very on children, the Urchin saddle has been carefully shaped to suit the specific needs of younger riders, giving comfort that lasts on day long trail sessions.This kids mountain bike saddle is 137mm wide and uses light, high-density foam for maximum comfort & wear. It features a hard-wearing cover, which is perfect at handling multiple changes to riding positions and the demands that a younger rider will put on the saddle.
This is a genuine replacement gear hanger, compatible with all Nukeproof Digger Frames.
In comparison to their firmer "Endurance" model, which aims to be as durable as possible, this "Race" model uses a much softer and grippier A15 Kraton compound to help you maintain your hand position. Ultimate Comfort and Control The Horizon Race grips also feature a unique, multidirectional, and tapered grip pattern that provides a cushioning effect in key areas and grip in all directions. So, whether you prefer to ride with or without gloves, you'll enjoy consistent and comfortable grip no matter how hard you're pushing yourself! Locked on and Supportive With lockrings on either end, these grips are going nowhere. Even as you throw yourself into the berms and land the biggest jumps, they'll maintain a secure connection with the bar. These grips have an asymmetrical inner flange to provide support without obstructing access to your shifter.
The Sam Hill Signature series is a no-compromise range of race ready components chosen by Sam as the tools for the job. Sam has always been particular about his setup and Nukeproof has taken great pride in developing no nonsense, custom products for Sam with some innovation even coming from his motocross bike! Together, we have helped to produce World level products that everyone can use. The entire Sam Hill Signature Series also feature matching graphics which were inspired by Sam himself.