Shelter Wheel Kit is made of 35 washers that fit snugly over the valve stem, gluing at its base, with an elegant and almost invisible silencing effect.It's also great to balance wheels, with an additional vibration-reducing action.Key Features:Eliminates valve noises, especially on high-profile rims,Shelter washers can be used to finely balance wheels,Visco-Elastic behaviour reduced vibrations.How to silence valves:Shelter Wheel Kit is made of 35 washers that fit snugly over the valve stem, gluing at its base. With minimum bulk and weight, they provide an elegant and almost invisible silencing effect, cancelling unwanted valve movements and vibrations. The re-sealable bag makes sure washers retain their properties if needed for successive applications.Once Shelter washers are applied on the rim, it’s possible to remove the valve an re-insert it without loosing the silencing effect. This is just one application of our Shelter Wheel Kit, but there’s more.Nobody would drive a fast car whose wheels haven’t been carefully balanced after mounting tyres on.Current high performance bicycle wheels, with fancy ceramic bearings, lightweight carbon rims, cannot deliver their full potential if not properly balanced.It’s an easy task that only requires a Shelter Wheel Kit, a wheel truing stand (or a bicycle turned upside down..), patience and some minutes per wheel.Much nicer and effective than electrical tape to silence valves on high-end wheelsMuch nicer (and effective) than electrical tape to silence valves on high-end wheelsHow to balance wheels:Mount the tyre (and eventually disk) on the wheel, so that the wheel is in its rideable form.IMPORTANT: if balancing a tubeless wheel, make sure there’s very little or no liquid sealant inside (that can be added later). Liquid sealant spreads while riding without creating wheel unbalance, but it will interfere with static balancing.Place the wheel on a truing stand and make sure it can rotate freely.With a gentle push, make the wheel spin. After a few complete rotations in the direction of the push, the wheel will enter a pendulum phase where it makes partial rotations, back and forth. Behaving like a pendulum, the excess of weight on the wheel is subject to a restoring force (due to gravity) that accelerates it toward the equilibrium position. Amplitude of swings will reduce until the wheel stops: the lowest point is where the excess weight is.Often wheels stop with the valve at the lowest point… but sometimes uneven weight distribution on the tyre or less-than-accurate carbon fiber lay up overcompensate that, and the lowest point is not corresponding to the valve.Keeping the lowest point of the rim/tyre as reference, identify the opposite point on the rim (you can find it using a ruler, aligned with the lowest point and the wheel axle) and adhere a Shelter washer there.Repeat the process from #1. Each time the heaviest point may move slightly (because of friction in the hub), but it will normally remain within a +-10 cm (4 inches) range.The wheel is balanced when, upon making it turn, IT WILL STOP WITHOUT ENTERING THE PENDULUM PHASE (it won’t change its rotation sense). With each subsequent spin, the lowest point when the wheel stops is a random point on the circumference, changing every time and depending on bearing friction.Washers can be adhered one on top of the other, or side by side, on top of the rim or on its side (depending on rim profile/size).A good trick, although not always possible, is finding a spoke that’s close to the lightest point of the wheel and cutting the washer on one side, so that the washer can be put around the spoke.Each Shelter washer weights around 1 g. Typical wheel unbalance ranges from 4 to 12 grams.Visco-elasticity reduces vibrations:That’s an added bonus when balancing a wheel with Shelter washers.The transmission of vibrational energy through any structure can be reduced by introducing visco-elastic materials at discrete points. It’s exactly what Shelter does, contributing to reduce vibrations on very stiff wheels.
With tubeless tyres becoming more and more prevalent, never has there been a better time to invest in tyre sealant. Effetto Mariposa's Caffelatex Tyre Sealant is an innovative sealant that has long been proven at the highest level on and off-road. Highly effective tyre sealant that lasts up to 2 years in a tubular tyreFoaming action when wheel is turning helps to prevent puncturesMicroscopic silicate particles also help to provide quicker sealing, resulting in less air loss when you punctureSeals holes up to 5mm on an MTB tubeless tyreContains no ammonia and is non-corrosive, making it safe to use in tubular tyresCaffelatex's formula contains microscopic silicate particles, allowing the sealant more time to seal holes up to 5mm. These particles are so small, at less than 2 microns in diameter, that the sealant is still highly fluid and easily coats the inside of your tyre or tubular. The formula also has a foaming action when the wheel is spinning, further helping to improve the sealing of any punctures.Not only is Caffelatex sealant highly effective at sealing punctures, it is also incredibly durable. Thanks to its innovative formula, the sealant can last up to 2 years depending on the application and the external conditions. When using the sealant in a tubular tyre with a latex inner tube, you can expect the sealant to last between 1-2 years. For tubeless-ready tyres the sealant lasts 4-6 months, so you can go a long time between fill ups and enjoy puncture-free riding for months on end before you need to check if the sealant has dried out. Durable, reliable and excellent at sealing punctures, the Effetto Mariposa Caffelatex tyre sealant is some of the best you can buy.
The Vegetalex from Effetto Mariposa is a plant-based tyre sealant with all natural repairing ingredients. Plant-based puncture repairing ingredientsLightweight & Extremely durableCompatible with the use of CO2 cartridgesBiodegradable and totally plastic freeLow maintenanceEasy to cleanWhy we created it - Our tyre sealant Caffélatex has a strong palmarès of victories to demonstrate its performance, together with a solid and constantly growing base of happy users, worldwide. As we should all do our best to reduce our impact on the environment, we started working on a plant-based sealant that was both good with nature and very effective similar to Caffélatex - against punctures. It took us more than two years of development, but we can now say Vegetalex has exceeded our expectations.Plant-based puncture repairing ingredients - Most tyre sealants employ slowly biodegradable liquid polymers (like natural or synthetic latex) to repair punctures; Vegetalex instead contains only plant-based particles and fibres - finely ground olive stones and cellulose fibres - to deliver a tremendous puncture clogging effect. This mix, held together by xanthan gum (produced from simple sugars), fixes punctures ranging from small tyre porosities to bigger cuts (up to 5 mm) fast and in a permanent way.Extremely durable - Durability was one of the priorities for the Vegetalex project. As it doesn t rely on the solidification of a liquid polymer to fix punctures, rather on a sophisticated mix of different shapes and sizes of natural particles with xanthan gum, Vegetalex has a long active lifespan inside tyres. Starting at 3 months in worst-case scenarios (very porous tyres in hot weather and small quantity of sealant), Vegetalex will keep repairing punctures for more than 6 months inside most tyres. This makes it also suitable for inner-tube applications.Lightweight - Vegetalex has been finely tuned to obtain a high mobility, so that a small quantity goes a long way in terms of coverage of the inner surface of the tyre. For Vegetalex, we suggest using about 20% more than the quantities recommended by the iCaffelatex app for Caffélatex. As an example, for a 29x2.10 (54-622) tubeless-ready tyre iCaffelatex recommends a minimum of 70 ml (approx. 2 ½ oz.) of Caffélatex or 84 ml (approx. 3 oz.) of Vegetalex.Compatible with the use of CO2 cartridges - Vegetalex isn t damaged by the use of CO2 cartridges.Biodegradable and totally plastic free - Vegetalex doesn t contain ammonia or other aggressive chemicals, nor is it toxic or corrosive. Vegetalex doesn t contain macro or micro plastics, no rubber particles (please note: recycled rubber decomposes very slowly!), no aramid fibres (that will remain in the environment for a long time...): all the ingredients of Vegetalex are highly biodegradable. Vegetalex doesn t trigger allergic reactions in people who are allergic to products made with natural rubber latex. However, it may contain traces of nut.Low maintenance - Being able to forget about tyre sealant is the dream of tubeless tyre users. Especially those of us who don t ride too often, wondering whether the sealant is still liquid inside our tyres (or not) is a worry that can spoil the pleasure of a ride. We say that Vegetalex is ideal for e-bikes because e-bikers often have to deal with more complex machines, batteries, and electronics; a sealant that s low maintenance is surely a welcome change. Using more structured tyres, like those specific for e-bikes, Vegetalex will easily last a full season of riding, so that you can spend less time doing bicycle maintenance and more time riding.Easy to clean - Vegetalex doesn t contain pigments or quickly solidifying polymers so it is very easy to remove from surfaces. Even when dry, Vegetalex can be cleaned with soapy water and a brush.Additional tips - It s important to shake Vegetalex bottle well before injecting the sealant into tyres. If extra protection is needed - for example taking a multiple days ride on rocky, thorny terrain we suggest adding 30 ml of product to the recommended quantity.
The final part of any tubeless kit is the valves. Designed to fit snugly in the rim's valve hole, the Effetto Mariposa Caffelatex Tubeless Valve is lightweight, easy to use and incredibly durable.Lightweight and durable aluminium constructionConic adaptors allow them to adapt to any rim profileSuitable for presta or schrader rimsRemovable valve cores make sealant injection easyThe Caffelatex Tubeless Valves come with clever conic adaptors that allow them to be used with rims drilled for both presta and schrader valves. Constructed from lightweight aluminium, the valves are incredibly durable and also look great. Removable valve cores also make it easy to inject your sealant of choice through the valves and into the tyre. Versatile, lightweight and easy to use, the Effetto Mariposa Caffelatex Tubeless Valves are some of the best you can buy.
The Effetto Mariposa Mangiacatena Chain Cleaner is for quick and effective chain cleaning without the need to remove the chain from the bike, use a chain cleaning tool rather than simple brushes.Effective chain cleaning toolSix rotating brushes clean deep in to chainSturdy handleDual direction design, great on e-bikesReplacement brush kit availableWorks on 5 speed chains, up to 13 speedsMaximum chain width 9mmAlso suitable for single speed transmissionsThe Mangiacatena (Translation: Chain Eater) will thoroughly de-grease and clean the whole chain. It is the tool of its type to be equipped with lamellar (finned) elements at both ends, meaning the degreaser is contained when the chain is moved in either direction. This saves on degreaser, is less messy and very useful on many ebikes where only pedalling forwards moves the chain.Once the tool is assembled around the chain, degreaser is added to the fill level (Effetto Allpine Extra recommended). The chain follows a simple, low resistance path straight through Mangiacatena. First it is squeezed at both ends by the plastic fins then scrubbed clean by six rotating brushes which get soaked in the degreaser.For best results move the chain ten times through Mangiacatena with the tool installed below the Chainstay then repeat with it mounted above the Chainstay. Dispose of the dirty degreaser correctly then repeat the first stage but with water to rinse the chain and brushes. Finally dry the chain with a clean cloth before re-lubrication.
Effetto Mariposa Vegetalex Tyre Sealant (1000ml)Featuring a biodegradable and totally plastic-free formula, this 1000ml bottle of high-quality tyre sealant is great for the environment. In addition, its revolutionary design makes it long-lasting as well as providing riders with a high level of puncture protection for tubeless, tubular and inner-tube applications.Extremely DurableDurability was one of the priorities for the Végétalex project. As it doesn't rely on the solidification of a liquid polymer to fix punctures, rather on a sophisticated mix of different shapes and sizes of natural particles with xanthan gum, Végétalex has a long 'active' lifespan inside tyres.Starting at three months in worst-case scenarios (very porous tyres in hot weather and a small quantity of sealant), Végétalex will keep repairing punctures for more than six months inside most tyres. This makes it also suitable for inner-tube applications.Features: Size: 1000ml Unique plant-based puncture repairing ingredients Adds little weight to wheels Extremely durable Compatible with the use of CO2 cartridges Biodegradable and totally plastic-free Very low maintenance Easy to clean Manufacturer's Part Number: E-EMCHVT1000Technologies: Plant-based Puncture Repairing Ingredients: Most tyre sealants employ slowly biodegradable liquid polymers (like natural or synthetic latex) to repair punctures; Végétalex instead contains only plant-based particles and fibers - finely ground olive stones and cellulose fibers - to deliver a tremendous puncture clogging effect. This mix, held together by xanthan gum (produced from simple sugars), fixes punctures ranging from small tyre porosities to bigger cuts (up to 5 mm) fast and in a permanent way. Lightweight: Végétalex has been finely tuned to obtain a high mobility, so that a small quantity goes a long way in terms of coverage of the inner surface of the tyre. For Végétalex, we suggest using about 20% more than the quantities recommended by the iCaffelatex app for Caffélatex. As an example, for a 29×2.10 (54-622) tubeless-ready tyre iCaffélatex recommends a minimum of 70 ml (approx. 2 1⁄2 oz.) of Caffélatex or 84 ml (approx. 3 oz.) of Végétalex. Compatible with the use of CO2 Cartridges: Végétalex isn't damaged by the use of CO2 cartridges. Low Maintenance: Being able to 'forget' about tyre sealant is the dream of tubeless tyre users. Especially those of us who don't ride too often, wondering whether the sealant is still liquid inside our tyres (or not) is a worry that can spoil the pleasure of a ride. We say that Végétalex is ideal for e-bikes because e-bikers often have to deal with more complex machines, batteries, and electronics; a sealant that's low maintenance is surely a welcome change. Using more structured tyres, like those specific for e-bikes, Végétalex will easily last a full season of riding, so that you can spend less time doing bicycle maintenance and more time riding. Easy to Clean: Végétalex doesn't contain pigments or quickly solidifying polymers so it is very easy to remove from surfaces. Even when dry, Végétalex can be cleaned with soapy water and a brush.Buy Effetto Mariposa Wheels & Tyres from Chain Reaction Cycles, the World's Largest Online Bike Store.
Effetto Mariposa Caffelatex Mountain Bike Tubeless KitCaffélatex is a truly innovative tyre sealant, free of ammonias and other aggressive chemicals; it is kind to the tyre casing and provides an excellent seal for punctures up to 6mm. It now comes in a handy kit containing everything you need to convert your wheels to tubeless. This complete kit comes in a handy tool bottle, containing a 250ml bottle of sealant, one roll of tubeless tape (enough for two wheels), and two tubeless valves with conic adapters for Schrader or Presta compatibility. The kits come in small, medium or large, designating the width of rim tape provided. Features: Complete tubeless kit in a functional Tool Bottle Presta valves with conic adapters for Schrader drilled rims Anodised Red valve caps Size: S - 20-24mm; M - 25-29mm; L - 30-34mm Kit Contains: 1 Portatutto tool bottle (as functional packaging) 1 bottle of Caffélatex sealant, 250ml, with measuring over-cap 1 roll of Caffélatex Tubeless Tape (S, M or L version, depending on the kit) 2 Caffélatex Tubeless Valves with conic adapters (for both Presta and Schrader-drilled rims) and a key for Presta mechanisms Branded Sticker Instruction leafletBuy Effetto Wheels & Tyres from Chain Reaction Cycles, the World's Largest Online Bike Store.
Effetto Mariposa Caffelatex Mountain Bike Tubeless KitCaffélatex is a truly innovative tyre sealant, free of ammonias and other aggressive chemicals; it is kind to the tyre casing and provides an excellent seal for punctures up to 6mm. It now comes in a handy kit containing everything you need to convert your wheels to tubeless. This complete kit comes in a handy tool bottle, containing a 250ml bottle of sealant, one roll of tubeless tape (enough for two wheels), and two tubeless valves with conic adapters for Schrader or Presta compatibility. The kits come in small, medium or large, designating the width of rim tape provided. Features: Complete tubeless kit in a functional Tool Bottle Presta valves with conic adapters for Schrader drilled rims Anodised Red valve caps Size: S - 20-24mm; M - 25-29mm; L - 30-34mm Kit Contains: 1 Portatutto tool bottle (as functional packaging) 1 bottle of Caffélatex sealant, 250ml, with measuring over-cap 1 roll of Caffélatex Tubeless Tape (S, M or L version, depending on the kit) 2 Caffélatex Tubeless Valves with conic adapters (for both Presta and Schrader-drilled rims) and a key for Presta mechanisms Branded Sticker Instruction leafletBuy Effetto Wheels & Tyres from Chain Reaction Cycles, the World's Largest Online Bike Store.
Not all modern mountain bike rims are tubeless compatible, so if you want to take the tubeless plunge but don't want to invest in new wheels, the Effetto Mariposa Caffelatex Tubeless strip is the answer.Lightweight, puncture resistant transparent rim strip makes tubeless conversion easyFit strip and valves to wheels, add sealant to tubeless or tubeless-ready tyres, inflate and go for a rideLong lasting construction can be moved from wheel to wheelSold as a kit including two rim strips and two 40mm tubeless valvesWhile more and more rims are designed from the outset to be used with tubeless and tubeless-ready tyres, there are still a huge number only designed to take tubes. Rather than investing in a new set of wheels, the Effetto Mariposa Caffelatex Rim Strip allows you to convert your regular inner-tube only wheels to tubeless-ready, so you can enjoy puncture-free riding.When using the Caffelatex Rim Strip, you can remove your current rim tape or cloth and install the strip. This is the first step in setting your wheels and tyres up tubeless. The strip helps to make the rim as air tight as possible. When combined with the tyre sealant, this keeps the tyres inflated and more resistant to punctures. The width of the tape varies, so you must select the right size for your rim. The Small Kit suits rims with an external section of 20-24mm, Medium suits 25-29mm and Large suits 30-34mm wide rims. Once the strip and valves are installed you can install your tubeless or tubeless-ready tyres, add your sealant of choice, inflate the tyres and you're good to go! You can finally kiss punctures goodbye. The strips and valves are incredibly durable, so you can easily swap them between wheels if you need to. Thanks to the Effetto Mariposa Caffelatex Rim Strip, you no longer need to have a set of expensive tubeless or tubeless-ready wheels to enjoy the benefits of such a setup.
Not all modern mountain bike rims are tubeless compatible, so if you want to take the tubeless plunge but don't want to invest in new wheels, the Effetto Mariposa Caffelatex Tubeless strip is the answer.Lightweight, puncture resistant transparent rim strip makes tubeless conversion easyFit strip and valves to wheels, add sealant to tubeless or tubeless-ready tyres, inflate and go for a rideLong lasting construction can be moved from wheel to wheelSold as a kit including two rim strips and two 40mm tubeless valvesWhile more and more rims are designed from the outset to be used with tubeless and tubeless-ready tyres, there are still a huge number only designed to take tubes. Rather than investing in a new set of wheels, the Effetto Mariposa Caffelatex Rim Strip allows you to convert your regular inner-tube only wheels to tubeless-ready, so you can enjoy puncture-free riding.When using the Caffelatex Rim Strip, you can remove your current rim tape or cloth and install the strip. This is the first step in setting your wheels and tyres up tubeless. The strip helps to make the rim as air tight as possible. When combined with the tyre sealant, this keeps the tyres inflated and more resistant to punctures. The width of the tape varies, so you must select the right size for your rim. The Small Kit suits rims with an external section of 20-24mm, Medium suits 25-29mm and Large suits 30-34mm wide rims. Once the strip and valves are installed you can install your tubeless or tubeless-ready tyres, add your sealant of choice, inflate the tyres and you're good to go! You can finally kiss punctures goodbye. The strips and valves are incredibly durable, so you can easily swap them between wheels if you need to. Thanks to the Effetto Mariposa Caffelatex Rim Strip, you no longer need to have a set of expensive tubeless or tubeless-ready wheels to enjoy the benefits of such a setup.
Shelter is a self-adhesive, transparent protection with visco-elastic behaviour that protects carbon-fibre or metal structures it’s applied to. Available in two versions, Road and Off-Road.Key Features:Shelter tape is a multi-layer acrylic protection tape which dissipates any impact energy on two axis. ,Each layer spreads loads vertically and horizontally, the impact energy decreases at each layer, protecting the bike frame. ,Perfect for carbon frames where the surface epoxy resin can be brittle and sensitive to impacts.,The tape is clear, does not hide graphics and can be applied easily.,Impact test video available for viewing below,Off Road - 1.2mm thick.,Road - 0.6mm thick.
This high-performance chain cleaner thoroughly cleans all chain speeds, from single speed all the way up to 10, 11, 12 and 13-Speed chains. If you want to clean the chain in a thorough way and reduce the amount of degreasing liquid used, Mangiacatena is the one for you. It is the first chain cleaner equipped with lamellar elements at both ends, so that the chain can be cleaned by moving it in both directions, very useful also for electric bikes (E-Bikes). Equipped with six rotating brushes and a sturdy handle. Chain Cleaning with Minimum Waste There is nothing wrong with cleaning the chain with the classic brush and solvent liquid in a tin. In that way, however, a lot of solvents are wasted without getting to deep cleaning, unless you want to disassemble the chain and immerse it in the solvent. To avoid disassembly and clean in depth, we have developed Mangiacatena: the best cleaning with the least amount of solvent, in a short time, leaving the chain on the bike. Please Note: Reducing the amount of solvent used doesn’t mean that cleaning takes place without getting dirty. Better to protect the floor with a cloth or work outside. Deep Cleaning Formula The chain runs straight inside Mangiacatena, squeezed at both ends between lamellar plastic (PE) elements with the task of keeping as much solvent inside as possible. The washing is performed by six rotating brushes, continuously soaked in the cleaning liquid, which actively removes dirt on each side, pushing the solvent inside the chain. Instructions for Use: Open Mangiacatena by removing the cover and positioning the lower part of Mangiacatena on the bottom span of the chain Mount the cover making sure it’s perfectly aligned with the lower part, then slide the locking handle in place until it is fully engaged Add the degreasing liquid through the upper holes (it is recommended to use Effetto Mariposa Allpine Extra) until the lower tank is full to the “FILL” level line Keeping Mangiacatena in position with the side handle, pedal backwards for at least 10 full revolutions Note: the two lamellar elements at both ends reduce the waste of solvent, but slow down the sliding of the chain at least in the initial phase… so don't be afraid, just hold the Mangiacatena firmly Note: thanks to the lamellar elements, Mangiacatena allows - without wasting solvent - to pedal in both directions. To do this, it is recommended to keep the rear wheel of the bicycle off the ground (using a workshop stand or other support) It is now possible to move Mangiacatena: release the side locking handle by depressing the thumb lever and remove it, open the cover, disassemble Mangiacatena from the lower span of the chain and position it, as already described, on the upper span of the chain, for a second cleaning step. Add more degreaser if necessary Keeping Mangiacatena in position using the side handle, pedal backwards for at least 10 full revolutions Disassemble Mangiacatena and empty the liquid contained inside (dispose of in accordance with the law if you use non-biodegradable degreasers or lubricants) Water rinse: mount Mangiacatena on the lower span of the chain, add water through the top holes and make at least 10 full revolutions Disassemble Mangiacatena and empty the liquid contained inside (dispose of it in accordance with the law if you use non-biodegradable degreasers or lubricants). Repeat from point 8 until perfect rinsing. In the end, rinse Mangiacatena with water and allow to air dry Dry the chain (rag, compressed air) and do not forget to lubricate it (we recommend our ecological Flowerpower Wax lubricant) Effetto Mariposa has selected Mangiacatena materials and construction for long life. They also provide a complete set of replacement brushes, Mangiacatena Replacement Kit, to replace what you wear without having to throw everything away. They have also chosen to use lamellar PE elements at both ends, instead of the more common sponges, for their greater durability and resistance For Single-Speed Transmissions and 5 to 13 Speed Chains The chain runs straight inside Mangiacatena, instead of following a tortuous path, making it also suitable for single-speed transmissions (for a chain with a maximum width of 9 mm). No problem for traditional 5 to 13 speed chains.
Effetto Mariposa Mangiacatena Chain CleanerThe Mangiacatena Chain Cleaner from Effetto Mariposa is a durable, efficient and fast acting chain cleaning device that scrubs deep into chain links. This high-performance chain cleaner thoroughly cleans all chain speeds, from single speed all the way up to 10, 11, 12 and 13-Speed chains.If you want to clean the chain in a thorough way and reduce the amount of degreasing liquid used, Mangiacatena is the one for you. It is the first chain cleaner equipped with lamellar elements at both ends, so that the chain can be cleaned by moving it in both directions, very useful also for electric bikes (E-Bikes). Equipped with six rotating brushes and a sturdy handle.Chain Cleaning with Minimum WasteThere is nothing wrong with cleaning the chain with the classic brush and solvent liquid in a tin. In that way, however, a lot of solvent is wasted without getting to a deep cleaning, unless you want to disassemble the chain and immerse it in the solvent. To avoid disassembly and clean in depth, we have developed Mangiacatena: the best cleaning with the least amount of solvent, in a short time, leaving the chain on the bike.Please Note: Reducing the amount of solvent used doesn't mean that cleaning takes place without getting dirty. Better to protect the floor with a cloth or work outside.Deep Cleaning FormulaThe chain runs straight inside Mangiacatena, squeezed at both ends between lamellar plastic (PE) elements with the task of keeping as much solvent inside as possible. The washing is performed by six rotating brushes, continuously soaked in the cleaning liquid, which actively remove dirt on each side, pushing the solvent inside the chain.Instructions for Use: Open Mangiacatena by removing the cover and positioning the lower part of Mangiacatena on the bottom span of the chain Mount the cover making sure it's perfectly aligned with the lower part, then slide the locking handle in place until it is fully engaged Add the degreasing liquid through the upper holes (it is recommended to use Effetto Mariposa Allpine Extra) until the lower tank is full to the “FILL” level line Keeping Mangiacatena in position with the side handle, pedal backwards for at least 10 full revolutions Note: the two lamellar elements at both ends reduce the waste of solvent, but slow down the sliding of the chain at least in the initial phase… so don't be afraid, just hold the Mangiacatena firmly Note: thanks to the lamellar elements, Mangiacatena allows - without wasting solvent - to pedal in both directions. To do this, it is recommended keeping the rear wheel of the bicycle off the ground (using a workshop stand or other support) It is now possible to move Mangiacatena: release the side locking handle by depressing the thumb lever and remove it, open the cover, disassemble Mangiacatena from the lower span of the chain and position it, as already described, on the upper span of the chain, for a second cleaning step. Add more degreaser if necessary Keeping Mangiacatena in position using the side handle, pedal backwards for at least 10 full revolutions Disassemble Mangiacatena and empty the liquid contained inside (dispose of in accordance with the law if you use non-biodegradable degreasers or lubricants) Water rinse: mount Mangiacatena on the lower span of the chain, add water through the top holes and make at least 10 full revolutions Disassemble Mangiacatena and empty the liquid contained inside (dispose of in accordance with the law if you use non-biodegradable degreasers or lubricants). Repeat from point 8 until perfect rinsing. At the end, rinse Mangiacatena with water and allow to air dry Dry the chain (rag, compressed air) and do not forget to lubricate it (we recommend our ecological Flowerpower Wax lubricant) Effetto Mariposa have selected Mangiacatena materials and construction for a long life. They also provide a complete set of replacement brushes, Mangiacatena Replacement Kit, to replace what you wear without having to throw everything away. They have also chosen to use lamellar PE elements at both ends, instead of the more common sponges, for their greater durability and resistanceFor Single-Speed Transmissions and 5 to 13 Speed ShainsThe chain runs straight inside Mangiacatena, instead of following a tortuous path, making it also suitable for single-speed transmissions (for a chain with a maximum width of 9 mm). No problem for traditional 5 to 13 speed chains.Features: The best way to clean the chain with minimum consumption of degreasing liquid The lamellar elements at both ends retain dirt and liquid inside Mangiacatena, while the six rotating brushes - continuously wet with degreaser - also act mechanically on the chain It can be used both on the lower and upper part of the chain, pedaling in both directions Degreasing liquid or water can be added from above, without the need to open Mangiacatena Made of shockproof and solvent resistant plastic. It can be refurbished with the appropriate replacement brush kit It works with single-speed transmissions (maximum chain width: 9 mm) and 5 to 13 speed chains Buy Effetto Mariposa Workshop from Chain Reaction Cycles, the World's Largest Online Bike Store.
Not all modern mountain bike rims are tubeless compatible, so if you want to take the tubeless plunge but don't want to invest in new wheels, the Effetto Mariposa Caffelatex Tubeless strip is the answer.Lightweight, puncture resistant transparent rim strip makes tubeless conversion easyFit strip and valves to wheels, add sealant to tubeless or tubeless-ready tyres, inflate and go for a rideLong lasting construction can be moved from wheel to wheelSold as a kit including two rim strips and two 40mm tubeless valvesWhile more and more rims are designed from the outset to be used with tubeless and tubeless-ready tyres, there are still a huge number only designed to take tubes. Rather than investing in a new set of wheels, the Effetto Mariposa Caffelatex Rim Strip allows you to convert your regular inner-tube only wheels to tubeless-ready, so you can enjoy puncture-free riding.When using the Caffelatex Rim Strip, you can remove your current rim tape or cloth and install the strip. This is the first step in setting your wheels and tyres up tubeless. The strip helps to make the rim as air tight as possible. When combined with the tyre sealant, this keeps the tyres inflated and more resistant to punctures. The width of the tape varies, so you must select the right size for your rim. The Small Kit suits rims with an external section of 20-24mm, Medium suits 25-29mm and Large suits 30-34mm wide rims. Once the strip and valves are installed you can install your tubeless or tubeless-ready tyres, add your sealant of choice, inflate the tyres and you're good to go! You can finally kiss punctures goodbye. The strips and valves are incredibly durable, so you can easily swap them between wheels if you need to. Thanks to the Effetto Mariposa Caffelatex Rim Strip, you no longer need to have a set of expensive tubeless or tubeless-ready wheels to enjoy the benefits of such a setup.
Not all modern mountain bike rims are tubeless compatible, so if you want to take the tubeless plunge but don't want to invest in new wheels, the Effetto Mariposa Caffelatex Tubeless strip is the answer.Lightweight, puncture resistant transparent rim strip makes tubeless conversion easyFit strip and valves to wheels, add sealant to tubeless or tubeless-ready tyres, inflate and go for a rideLong lasting construction can be moved from wheel to wheelSold as a kit including two rim strips and two 40mm tubeless valvesWhile more and more rims are designed from the outset to be used with tubeless and tubeless-ready tyres, there are still a huge number only designed to take tubes. Rather than investing in a new set of wheels, the Effetto Mariposa Caffelatex Rim Strip allows you to convert your regular inner-tube only wheels to tubeless-ready, so you can enjoy puncture-free riding.When using the Caffelatex Rim Strip, you can remove your current rim tape or cloth and install the strip. This is the first step in setting your wheels and tyres up tubeless. The strip helps to make the rim as air tight as possible. When combined with the tyre sealant, this keeps the tyres inflated and more resistant to punctures. The width of the tape varies, so you must select the right size for your rim. The Small Kit suits rims with an external section of 20-24mm, Medium suits 25-29mm and Large suits 30-34mm wide rims. Once the strip and valves are installed you can install your tubeless or tubeless-ready tyres, add your sealant of choice, inflate the tyres and you're good to go! You can finally kiss punctures goodbye. The strips and valves are incredibly durable, so you can easily swap them between wheels if you need to. Thanks to the Effetto Mariposa Caffelatex Rim Strip, you no longer need to have a set of expensive tubeless or tubeless-ready wheels to enjoy the benefits of such a setup.
Caffélatex is a truly innovative tyre sealant, successfully used on and off (MTB, cyclocross) road, for tubeless, tubular and inner-tube applications.CharacteristicsImproved formula (since January 2012):Thanks to the addition of microscopic silicate particles, Caffélatex now moves more slowly through holes, allowing the sealing ingredient more time to heal the puncture. These particles are NOT of macroscopic size (e.g., glitter 150-300 microns) but are instead microscopic particles less than 2 microns in diameter. Thus, Caffélatex flow characteristics change on a microscopic level without the headaches of valve-clogging glitter. Puncture repair speed is up to 5 times faster, an improvement especially noticeable with lightweight or thin-casing tiresFoaming action activated by wheel movement:The first advantage of Caffélatex over classic latex-based sealants comes from a foaming agent (Actifoam™), activated by wheel movement. Centrifugal force drives standard latex-based sealants against the outer circumference of the tyre. Caffélatex foaming action causes it to fill the tyre’s entire internal cavity , making it much more effective against sidewall punctures.Puncture-repairing action:Its fast sealing action makes Caffélatex ideal for MTB and road tubeless, tubular and standard tyres. Caffélatex repairs punctures up to 5 mm (mtb) and 3 mm (road).Stable over time:Thanks to its formula, Caffélatex is a very stable and durable sealant, but we know this is highly dependable on kind of application and external conditions.Using the recommended quantities for tyre size, the expected sealant lifespan is:Tubular (or Caffélatex inserted into latex/butyl inner tube): 1-2 years,UST Tubeless tyre: 4-6 months,Tubeless-ready tyre: 2-4 months,Tube-type tyre: 2-3 months,Nevertheless, in the impossibility of knowing our customers’ specific application (kind of wheel/tyre set-up, tyre sidewall thickness and porosities, external temperature and humidity, bicycle storage conditions…), we recommend checking Caffélatex every 2 months, to make sure it’s liquid and therefore retains its ‘puncture preventive’ action.,When dry, Caffélatex-sealed wheels are still air-tight, but Caffélatex won’t actively repair punctures..Not corrosive:being completely ammonia-free, its 100% tyre and rim friendly. It’s also a favourite sealant for cyclocross/tubular applications, creating no harm to the sensitive latex inner tubes.Usage and storage temperatures:From very cold to very hot, exceeding by far those of first-generation latex sealants (usage: -20/+50°C ~ storage: -15/ +30°C).Recommended quantities:30 to 50 ml per wheel for road/cyclocross applications; 50 ml for mtb tyres up to 26×2.10/29×2.00; 60 to 100 ml for mtb tyres over 26×2.10/29×2.00.Sizes:60ml pouch, 250ml or 1000ml bottles or 10 litre workshop tub
The final part of any tubeless kit is the valves. Designed to fit snugly in the rim's valve hole, the Effetto Mariposa Caffelatex Tubeless Valve is lightweight, easy to use and incredibly durable.Lightweight and durable aluminium constructionConic adaptors allow them to adapt to any rim profileSuitable for presta or schrader rimsRemovable valve cores make sealant injection easyThe Caffelatex Tubeless Valves come with clever conic adaptors that allow them to be used with rims drilled for both presta and schrader valves. Constructed from lightweight aluminium, the valves are incredibly durable and also look great. Removable valve cores also make it easy to inject your sealant of choice through the valves and into the tyre. Versatile, lightweight and easy to use, the Effetto Mariposa Caffelatex Tubeless Valves are some of the best you can buy.
Not all modern mountain bike rims are tubeless compatible, so if you want to take the tubeless plunge but don't want to invest in new wheels, the Effetto Mariposa Caffelatex Tubeless strip is the answer.Lightweight, puncture resistant transparent rim strip makes tubeless conversion easyFit strip and valves to wheels, add sealant to tubeless or tubeless-ready tyres, inflate and go for a rideLong lasting construction can be moved from wheel to wheelSold as a kit including two rim strips and two 40mm tubeless valvesWhile more and more rims are designed from the outset to be used with tubeless and tubeless-ready tyres, there are still a huge number only designed to take tubes. Rather than investing in a new set of wheels, the Effetto Mariposa Caffelatex Rim Strip allows you to convert your regular inner-tube only wheels to tubeless-ready, so you can enjoy puncture-free riding.When using the Caffelatex Rim Strip, you can remove your current rim tape or cloth and install the strip. This is the first step in setting your wheels and tyres up tubeless. The strip helps to make the rim as air tight as possible. When combined with the tyre sealant, this keeps the tyres inflated and more resistant to punctures. The width of the tape varies, so you must select the right size for your rim. The Small Kit suits rims with an external section of 20-24mm, Medium suits 25-29mm and Large suits 30-34mm wide rims. Once the strip and valves are installed you can install your tubeless or tubeless-ready tyres, add your sealant of choice, inflate the tyres and you're good to go! You can finally kiss punctures goodbye. The strips and valves are incredibly durable, so you can easily swap them between wheels if you need to. Thanks to the Effetto Mariposa Caffelatex Rim Strip, you no longer need to have a set of expensive tubeless or tubeless-ready wheels to enjoy the benefits of such a setup.
Not all modern mountain bike rims are tubeless compatible, so if you want to take the tubeless plunge but don't want to invest in new wheels, the Effetto Mariposa Caffelatex Tubeless strip is the answer.Lightweight, puncture resistant transparent rim strip makes tubeless conversion easyFit strip and valves to wheels, add sealant to tubeless or tubeless-ready tyres, inflate and go for a rideLong lasting construction can be moved from wheel to wheelSold as a kit including two rim strips and two 40mm tubeless valvesWhile more and more rims are designed from the outset to be used with tubeless and tubeless-ready tyres, there are still a huge number only designed to take tubes. Rather than investing in a new set of wheels, the Effetto Mariposa Caffelatex Rim Strip allows you to convert your regular inner-tube only wheels to tubeless-ready, so you can enjoy puncture-free riding.When using the Caffelatex Rim Strip, you can remove your current rim tape or cloth and install the strip. This is the first step in setting your wheels and tyres up tubeless. The strip helps to make the rim as air tight as possible. When combined with the tyre sealant, this keeps the tyres inflated and more resistant to punctures. The width of the tape varies, so you must select the right size for your rim. The Small Kit suits rims with an external section of 20-24mm, Medium suits 25-29mm and Large suits 30-34mm wide rims. Once the strip and valves are installed you can install your tubeless or tubeless-ready tyres, add your sealant of choice, inflate the tyres and you're good to go! You can finally kiss punctures goodbye. The strips and valves are incredibly durable, so you can easily swap them between wheels if you need to. Thanks to the Effetto Mariposa Caffelatex Rim Strip, you no longer need to have a set of expensive tubeless or tubeless-ready wheels to enjoy the benefits of such a setup.
This tubeless rim-strip makes tubeless conversions easy and quick. Unlike its butyl predecessors (from other brands), Caffélatex Strip is very light, puncture-proof and transparent. Made using a proprietary polymer blend, it is available in nine widths and two different wheel diameters each (26”/27,5” and 29”).Each kit contains two rim strips complete with tubeless valves. Mounting instructions are shown on the back of the header card.Why use a Strip when we already have a tubeless conversion tape?For some applications, the tape is great and it will always be lighter than a strip (8 g against 29 g per wheel... a butyl strip is around 65g). However, the tape takes time and some care/experience to be installed properly. There are then some applications where the tape simply won't work. i.e. the new cut-out rims for the new “+” and FAT size rims.Sold as kits containing two rim strips and two 40 mm tubeless valves (2 wheels per kit)Specifications:Small: 20 - 24mmMedium: 25 - 29mmLarge: 30 - 34mm27.5 Plus Small: 35 - 40 mm27.5 Plus Medium: 41 - 45mm27.5 Plus Large: 46 - 50mm26 Fat Small: 60 - 65mm26 Fat Medium: 75 - 80mm26 Fat Large: 95 - 100mm