Replacement axles for your Vault pedals.Sizes : 9/16",NB:Axle with the groove and uses the right had thread nut is the left hand (non drive side) axle. This axle tightens into the crank - aniclockwise. / Axle without the groove and uses the left had thread nut is the right hand (drive side) axle. This axle tightens into the crank - clockwise..
The current DMR Sidekick, Trailstar and Exalt frames all use a Swopout dropout specific to DMR frames. This allows you to change your dropout to your desired type on any of the framesVertical Swopout (Standard)Each of the Sidekick, Trailstar or Exalt comes equipped as standard with this Swopout.A 10mm vertical dropout with mech hanger. A direct replacement for your standard Swopout if you have an unfortunate stack. 12mm Bolt Through SwopoutEveryone likes a responsive feel to the rear of their bike. A bolt through hub is the ultimate way to achieve this. This Swopout will allow you to run a 12/135mm bolt through axle on the rear. DMR have the hubs to match on the hubs page. This setup is the choice of the pros.You can also upgrade the bolt through to a Maxle should you still which to run a quick release system, see the next Swopout along.10mm Horizontal SwopoutFor those you like single speed, for winter riding or prevention of wrecking expensive gears in a stack. This Swopout will allow you to run a 10mm hub single speed. If you need to keep things more secure than you quick release skewer will allow, check out the Chain Tug Mech Hanger for Swopout. 14mm Horizontal SwopoutSome of us play and ride hard, and need the equipment to mach.If you are the kind of person who hits the trails fast and hard, then consider a 14mm rear hub. This Swopout will allow you to run the super strong 14/135mm axle hub, DMR have the hub to mach this in our hubs section - single speed, again eliminating the risk of damage to gears.Maxle Bosses ONLY FOR USE WITH 12MM BOLT THRU SWOPOUT. These bosses bolt onto the 12mm Swopout allowing you to run a lighter and more user friendly Rockshox Maxle quick release axle with your DMR/Kinesis frame.
The DMR Deathgrip is Brendan Brendog Fairclough s signature grip, with a waffle and knurl flangeless design, the Deathgrip is made from soft Kraton rubber for maximum comfort and grip.Single lock-ring design with tapered core means no need for outer lock-ringIncredibly grippy waffle and knurl pattern on outer portionInner mushroom pattern for comfortSoft Kraton rubber for maximum comfort and vibration dampingThe tapered core means no outer lock ring is required while the inner mushroom pattern is great for additional comfort. The grip has been designed to offer maximum grip and excellent comfort, with a waffle and knurled design on the outer portion of the grip, combined with a mushroom pattern on the inner portion to improve comfort. Whether you re throwing yourself down the hill at the Redbull Rampage, a World Cup Downhill course or just out for a spin on your local trails, these grips have got you covered.
The DMR Deathgrip is Brendan Brendog Fairclough s signature grip, with a waffle and knurl flangeless design, the Deathgrip is made from soft Kraton rubber for maximum comfort and grip.Single lock-ring design with tapered core means no need for outer lock-ringIncredibly grippy waffle and knurl pattern on outer portionInner mushroom pattern for comfortSoft Kraton rubber for maximum comfort and vibration dampingThe tapered core means no outer lock ring is required while the inner mushroom pattern is great for additional comfort. The grip has been designed to offer maximum grip and excellent comfort, with a waffle and knurled design on the outer portion of the grip, combined with a mushroom pattern on the inner portion to improve comfort. Whether you re throwing yourself down the hill at the Redbull Rampage, a World Cup Downhill course or just out for a spin on your local trails, these grips have got you covered.
The DMR Deathgrip is Brendan Brendog Fairclough s signature grip, with a waffle and knurl design. This race version of the Deathgrip is made from an even softer "Race" Kraton rubber for maximum comfort and grip.Single lock-ring design with tapered core means no need for outer lock-ringIncredibly grippy waffle and knurl pattern on outer portionInner mushroom pattern for comfortSuper soft "Race" Kraton rubber for maximum comfort and vibration dampingThe tapered core means no outer lock ring is required while the inner mushroom pattern is great for additional comfort. The grip has been designed to offer maximum grip and excellent comfort, with a waffle and knurled design on the outer portion of the grip, combined with a mushroom pattern on the inner portion to improve comfort. Whether you re throwing yourself down the hill at the Redbull Rampage, a World Cup Downhill course or just out for a spin on your local trails, these grips have got you covered.
DMR Brendog DeathGrip - FlangeFeaturing a versatile design that's suitable for everything from all mountain (AM) riding to downhill (DH) racing, these mountain bike (MTB) bar grips are the second collaboration between DMR and Brendan "Brendog" Fairclough. Coming equipped with a super-soft Kraton compound, these deliver an excellent combination of comfort and reliability as you manoeuvre your ride across demanding terrain conditions. Their design started with an internally tapered single-lock core grip and wrapped Brendan's design around it, which includes a waffle and knurl pattern as well as a mushroom profile for extra comfort and support."I wanted to make the ultimate grip to go on all my bikes: AM to DH. I combined the following features and the DeathGrip is what we ended up with!" - Brendan Fairclough.Features: Material: Super-Soft Kraton Compound Use: Mountain Bike (MTB) Grip Pattern: Waffle and Knurl Size: Thin Option: 29.8mm; Thick Option: 31.3mm Mushroom for comfort Tapered core for security (no need for outer lock ring) Single or Pair: Pair Weight: 100g (per pair)Manufacturer's Part Number: DMR-G-BREN-THICK-GX Multi Galaxy Thick DMR-G-BREN-THICK-SG Sick Green Thick DMR-G-BREN-THIN-GX Multi Galaxy Thin DMR-G-BREN-THICK-NB Navy Blue Thick DMR-G-BREN-THIN-NB Navy Blue Thin DMR-G-BREN-THIN-SG Sick Green ThinBuy DMR Components from Chain Reaction Cycles, the World's Largest Online Bike Store.
DMR Brendog Death Grip MTB GripsThese grips are the result of a collaboration between DMR Bikes and Brendog (Brendan Fairclough). By combining an ergonomic mountain bike grip with a waffle section for better hold and a mushroomed thumb area, DMR's Brendog Death Grip MTB Grips are an excellent all-round grip for all-mountain, enduro and downhill riding.Features: Grip Type: MTB Knurl pattern makes for the best all-weather surface for your palm The waffle section provides additional grip at the frontMushroomed thumb area is really soft and malleableA tough closed end to protect your barsInner grip area is flanged to provide hand security Pair of two grips Weight: 100g (pair)Buy DMR Components from Chain Reaction Cycles, the World's Largest Online Bike Store.
DMR Brendog DeathGrip - FlangeFeaturing a versatile design that's suitable for everything from all mountain (AM) riding to downhill (DH) racing, these mountain bike (MTB) bar grips are the second collaboration between DMR and Brendan "Brendog" Fairclough. Coming equipped with a super-soft Kraton compound, these deliver an excellent combination of comfort and reliability as you manoeuvre your ride across demanding terrain conditions. Their design started with an internally tapered single-lock core grip and wrapped Brendan's design around it, which includes a waffle and knurl pattern as well as a mushroom profile for extra comfort and support."I wanted to make the ultimate grip to go on all my bikes: AM to DH. I combined the following features and the DeathGrip is what we ended up with!" - Brendan Fairclough.Features: Material: Super-Soft Kraton Compound Use: Mountain Bike (MTB) Grip Pattern: Waffle and Knurl Size: Thin Option: 29.8mm; Thick Option: 31.3mm Mushroom for comfort Tapered core for security (no need for outer lock ring) Single or Pair: Pair Weight: 100g (per pair)Manufacturer's Part Number: DMR-G-BREN-THICK-GX Multi Galaxy Thick DMR-G-BREN-THICK-SG Sick Green Thick DMR-G-BREN-THIN-GX Multi Galaxy Thin DMR-G-BREN-THICK-NB Navy Blue Thick DMR-G-BREN-THIN-NB Navy Blue Thin DMR-G-BREN-THIN-SG Sick Green ThinBuy DMR Components from Chain Reaction Cycles, the World's Largest Online Bike Store.
DMR Brendog Death Grip MTB GripsThese grips are the result of a collaboration between DMR Bikes and Brendog (Brendan Fairclough). By combining an ergonomic mountain bike grip with a waffle section for better hold and a mushroomed thumb area, DMR's Brendog Death Grip MTB Grips are an excellent all-round grip for all-mountain, enduro and downhill riding.Features: Grip Type: MTB Knurl pattern makes for the best all-weather surface for your palm The waffle section provides additional grip at the frontMushroomed thumb area is really soft and malleableA tough closed end to protect your barsInner grip area is flanged to provide hand security Pair of two grips Weight: 100g (pair)Buy DMR Components from Chain Reaction Cycles, the World's Largest Online Bike Store.
The DMR DeathGrip Race Edition is the second collaboration between DMR bikes and Brendog. ‘I wanted to make the ultimate grip to go on all my bikes: AM to DH. I combined the following features and the DeathGrip is what we ended up with!’ Brendan Fairclough. Tapered Core for Security. Waffle and Knurl for Grip. Mushroom for comfort. We started with an internally tapered single-lock core grip and wrapped Brendan's design around it in super-soft Kraton compound for the ultimate mountain bike handlebar grip. These DMR grips are available in various colours, soft or firm. Super Soft 'RACE DAY' Compound | Secret Super-Tacky Formula Tapered Core | No need for outer lock ring Single Lock Ring | Torque to 2nM Waffle and Knurl for grip Mushroom for comfort Available in Thin (ø29.8) or Thick (ø31.3) 100g per pair
The DMR DeathGrip Race Edition is the second collaboration between DMR bikes and Brendog. ‘I wanted to make the ultimate grip to go on all my bikes: AM to DH. I combined the following features and the DeathGrip is what we ended up with!’ Brendan Fairclough. Tapered Core for Security. Waffle and Knurl for Grip. Mushroom for comfort. We started with an internally tapered single-lock core grip and wrapped Brendan's design around it in super-soft Kraton compound for the ultimate mountain bike handlebar grip. These DMR grips are available in various colours, soft or firm. Super Soft 'RACE DAY' Compound | Secret Super-Tacky Formula Tapered Core | No need for outer lock ring Single Lock Ring | Torque to 2nM Waffle and Knurl for grip Mushroom for comfort Available in Thin (ø29.8) or Thick (ø31.3) 100g per pair
DMR does performance composite.Presenting the V11 pedal. For those that favour the durability, compliance and affordability of composite pedals, the new benchmark choice from DMR has arrived!The V11 is moulded with the same proven shape as the multi award-winning Vault pedal, providing a huge platform with DMR’s unique concave shape that allows your foot to sit deep into the centre for supreme grip.V11’s durable glass reinforced nylon body features eleven replaceable steel pins each side for rock solid grip. All pins are secured with captive locknuts for ultimate durability. Outer pins are Vault Moto pins that sink deep into your shoe, keeping your foot well and truly planted.V11 is fully rebuildable with the same proven internals as DMR Vault pedals, guaranteeing ride after ride with no-nonsense performance.
DMR V6 Flat PedalsBased on DMR's race proven V12 flat MTB pedals, the V6 model is made from a lightweight but durable Nylon and adopts the same narrow profile and concave shaping that DMR is renowned for. Also, for simplicity and to save weight, these flat mountain bike pedals rotate on a Dual DU bush internal system rather than internal bearings. Moulded pins complete these pedal's simple, high performing and maintenance-free design.Reasons to Buy:Race-proven design.Lightweight and durable Nylon construction.Narrow profile with concave shaping.High-performing and maintenance-free.Features:Material: NylonAxle: ChromolyAxle Size: Standard 9/16"" threadBearing Type: N/A pedal use DU (dry unlubricated) bushings insteadSpare Pins Included: N/A as pins are mouldedDual DU bush systemLightweight and durable Nylon construction.Narrow profile with concave shaping.Full length off-road pinsNon-serviceable designWeight: 327g (pair)Buy DMR Components from Chain Reaction Cycles, the World's Largest Online Bike Store.
These DMR chain tugs with hanger are designed to keep your 10mm axle hub in place within your 10mm horizontal dropout frame. These DMR chain tugs are adjustable from side to side at the point of contact with the dropout to keep the tugs perfectly square. DMR spares are solid, properly designed and rider tested for excellent performance. DMR was kicked into life in the winter of 1995, with the idea to make UK designed bike parts that worked for the way they like to ride.
DMR Moto DJ MTB TyreCreated in collaboration with Vee Tire Co., the Moto DJ retains the performance and aesthetic of the Supermoto, but modernised as a modern performance tyre. This is the number one choice for Dirt Jumps, Pumptracks, Skateparks and Street. Created to replace the rider-favourite SuperMoto model, the DMR Moto DJ MTB Tyre has a lighter construction, a fast-rolling tread and even better cornering grip than before.Features: Lightweight construction with a fast-rolling pattern Knurled "micro-grip" contact surface for skate-park type riding TPI: Steel Bead: 60tpi; Folding Bead: 120tpi Single or Pair: Single Weight: Steel Bead Option: 750g; Folding Bead Option: 695gTechnologies: Compact and aggressive low-profile tyre tread blocks give firm positive grip on hardpack dirt and street terrain. Round tyre profile with slightly taller shoulder blocks for extra bite in the berms. Low block height reduces weight and makes the tread blocks stiffer giving better bite. Available in Steel bead or Folding bead. Folding bead option has a super supple 120tpi casing. Buy DMR Wheels & Tyres from Chain Reaction Cycles, the World's Largest Online Bike Store.
DMR Replacement Chain Tugs & Mech HangerThe ideal replacement parts for your DMR components, this Chain Tugs & Mech Hanger has been constructed for optimised performance and has been thoroughly tested for long-lasting output. Made and engineered in the UK, these parts are suitable for use with DMR frames with horizontal dropouts. Features:Compatible With: For DMR frames with horizontal dropouts, may fit other frames with horizontal dropoutsCome with a non-drive side chain tensioner (tug) as wellMade in the UKMaterial: AluminiumDimensions: 10mmWeight: 12 grams (approx.)Buy DMR Accessories from Chain Reaction Cycles, the World's Largest Online Bike Store.
DMR Brendog DeathGrip - FlangelessThe second collaboration between DMR and Brendan "Brendog" Fairclough, these flangeless bar grips feature a versatile design that's suitable for everything from all mountain (AM) riding to downhill (DH) racing."I wanted to make the ultimate grip to go on all my bikes: AM to DH. I combined the following features and the DeathGrip is what we ended up with!" - Brendan Fairclough.Coming equipped with a high-quality Kraton rubber compound, these MTB flangeless bar grips offer an excellent blend of comfort, strength and reliability wherever your next ride takes you. Each grip is kitted out with a waffle and knurl pattern as well as a mushroom profile for a supportive hold as you charge across demanding terrain conditions. With an internally tapered single-lock core grip and Brendan's design wrapped around it, the DMR Brendog DeathGrip Flangeless bar grips are well equipped for the demands of modern trail-riding.Features: Material: Kraton Use: Mountain Bike (MTB) Size: Thin Option: 29.8mm; Thick Option: 31.3mm Grip Pattern: Waffle and knurl Mushroom for comfort Tapered core (no need for outer lock ring) Weight: 100g (pair)Manufacturer's Part Number: DMR-G-BREN2-THICK-GX Multi Galaxy Thick DMR-G-BREN2-THICK-NB Navy Blue Thick DMR-G-BREN2-THICK-SG Sick Green Thick DMR-G-BREN2-THIN-GX Multi Galaxy Thin DMR-G-BREN2-THIN-NB Navy Blue Thin DMR-G-BREN2-THIN-SG Sick Green ThinBuy DMR Components from Chain Reaction Cycles, the World's Largest Online Bike Store.
DMR Brendog Race Death Handlebar GripsThe Brendog Race Death Handlebar Grips from DMR is the creation of a collaboration between DMR and freeride legend Brendan 'Brendog' Fairclough. Designed to combine a waffle section with an MTB (mountain bike) grip and the added benefit of a mushroom thumb area, these grips tick all the boxes for MTB, enduro and downhill riders. Features: Super Soft "Race Day" Compound Secret Super-Tacky Formula Tapered Core, no need for an outer lock ring Single Lock Ring (Torque to 2nM) Waffle and Knurl for grip Mushroomed thumb area for comfort Available in Thin (29.8mm) or Thick (31.3mm)Use: MTB/Enduro/DownhillBuy DMR Components from Chain Reaction Cycles, the World's Largest Online Bike Store.
The DMR Death Grip Race version has a “Race Day” compound that is wrapped around an internally tapered core, which combines with the grip's mushroomed thumb area to disperse vibrations and sudden shocks. To enhance the grip and comfort level even further, this pair of grips have a combo waffle/knurled grip design. This gives you the option of mounting the DMR Deathgrip race edition with the grip type you prefer on the bottom or the top.
The DMR Death Grip Race Edition grips have a “Race Day” compound that is wrapped around an internally tapered core, which combines with the grip's mushroomed thumb area to disperse vibrations and sudden shocks. To enhance the grip and comfort level even further, this pair of grips have a combo waffle/knurled grip design. This gives you the option of mounting the DMR Brendog Race Death Grip with the pattern you prefer on the bottom or the top.