SRAM PressFit 30 to BSA Adaptor KitGenuine SRAM bottom bracket convertor. Designed to convert a PressFit 30 BB shell to a traditional BSA thread.Features:Polymer cupsSet includes left- and right-hand cupsSealed cups keep out dirt and waterMaintenance freeCompatible with 68/73mm shells46mm cup diameterBSA inner ThreadEasy press-fit installationBicycle bottom brackets connect the cranks to the bike and allow the crank arms to rotate. There are various sizes of bottom bracket shell on the market, so compatibility needs to be checked. The three most common frame bottom bracket shell widths are 68mm (English threaded road and mtb), 70mm (Italian threaded road) and 73mm (British threaded mtb). There are also many axle shapes and styles, from JIS or ISO square tapers through to the round splined axles such as ISIS or Octalink and then there is the new external cup systems which have the axle built into the crank arms. Some frames are now using the new BB30 system which uses bearings pushed directly into the frame and removes the needs for cups to be threaded into the frame.
Flawless shifting means you’ll never again compromise your speed and power in unpredictable off-road terrain.
SRAM's EX1 Trigger Shifter is specifically tuned for use with E-MTB bikes power assisted drivetrains, and as it’s equipped with SRAM'S X-Actuation™ technology, shifts are precise, fast, and efficient. It's also specifically tuned to deliver one accurate shift at a time, so you avoid over shifting to the wrong gear, thus extending your E-MTB's battery life and decreasing component wear and tear.
SRAM batteries are literally a snap to remove and charge. Just flip the tool-free battery latch up and slide the battery up and out of the derailleur. Then snap the battery into the USB powered SRAM eTap battery charger and connect the charger to any USB power source or A/C USB adaptor. A full charge takes up to 60 minutes to complete.
A variant of the external bottom bracket, this SRAM BB86 GXP PressFit bottom bracket cuts weight and provides easier installation by allowing you to press the bearing cups into the frame instead of threading them. There's no change to the crank - spindle length and diameter remain the same. Technologies: GXP: Other systems rely on side-loaded bearings to eliminate play, causing bearing wear. GXP captures the left-side bearing between the spindle and the left crankarm and allows the drive-side bearing to float axially on the spindle. There's no need to side-load bearings during adjustment. No excess wear and much simpler installation. Just tighten to the proper specifications and you're ready to roll, worry-free. GXP's two bicycle-specific cartridge bearings and eight seals ensure a smooth, long-lasting ride. SRAM's Gutter seal system takes a two-stage approach in directing contaminates away from the bearings providing longer bearing life. GXP’s Gutter Seal design also reduces friction, 35% less drag than previous versions, improving rider feel and performance. Gutter seal system has deeper installation tool grooves which provide stability and support while applying torque to the adapter cups. SRAM'S design and material choice have dropped 15g out. PressFit cuts weight. Easier installation by allowing you to press the bearing cups into the frame. GXP compatible. Easy installation. ISO 4210 compliant. See Declaration of Conformity for details. Manufacturer's Part Number: 00.6415.033.020 Black 92mm - MTB Hollowtech Eng 00.6415.033.000 Black BB86 - Road
Pressfit BB to convert PF30 to BSA threaded
This superb disc brake levels the playing field with power and reliability stuffed into a lightweight package. Additionally, its strong and reliable aluminium construction makes it ideal for tackling the trails and offroad riding conditions. This is a perfect choice of upgrade or replacement for your old or worn-out existing model. Technologies: Direct Link: SRAM's DirectLink lever design produces a solid, positive feel the second you squeeze the lever to engage the brake. It offers a no-nonsense solution to give you precise control. DOT 5.1: Heat is an enemy of any brake system, so advancements in heat management mean advancements in your ride. SRAM found that in their systems DOT 5.1 takes almost three times longer to boil than DOT 4, thus allowing flawless, fade-free performance in even more extreme conditions. Expandable Bladder: SRAM's new brake lever design includes a reshaped bladder that helps regulate and reduce air bubbles. The bladder is specifically shaped to evacuate air from the lever and push the fluid exactly where it's needed. The result is improved backpressure relief, which produces dependable braking power and consistency. PiggyBack Reservoir: The brake fluid reservoir on SRAM's latest lever design is optimised for both performance and ease of use. The PiggyBack Reservoir offers a simple, failsafe way to manage brake fluid, and also allows for ambidextrous lever placement. Timing Port Closure: A hydraulic brake's timing port is the connection between the reservoir and the master cylinder bore. When the lever is squeezed, a cup seal passes this area and closes the port, which pressurises the system. SRAM's new timing port closure system features durable seals and an ultra-smooth cylinder bore finish, producing dependable braking power and consistency.
Built for precise and swift shifting across our wide range 11-speed cassette, the NX Grip Shift brings industry changing technology to everyone.
At the heart of the SRAM Eagle 12-Speed drivetrain is the Eagle line of high-performance chains. This SRAM NX eagle 12 speed chain ensures exceptional compatibility, shifting performance and reliability with all Eagle drivetrains. An official Eagle 12-Speed chain guarantees smooth, silent and efficient transmission performance for every pedal rotation, gear change and every second riding on the side of the mountains. The basis of every Eagle drivetrain is its chain-and the NX Eagle chain is designed and manufactured using genuine SRAM's Eagle architecture, so it is fully compatible with every other component in the Eagle ecosystem. The NX Eagle chain features solid pin construction, Eagle PowerLock and smooth, efficient shifting that you can count on every time out. Flow Link: Ultra-smooth chain inner-plates are completely devoid of square edges, resulting in a chain that engages the cassette and chainring with far less friction, for quieter performance and better wear life. The design allows a narrower overall profile and a flatter outer-plate that can withstand greater shifting angles. This means more consistent chain riveting and enhanced overall strength is achieved. PowerLock: SRAM chain engineers developed PowerLock as a tool free and consistent way to connect mountain bike chains. While PowerLock does not require special tools for installation, the especially tight tolerances of 10, 11 and 12-Speed drivetrains mandate that each PowerLock is good for a one-time application only. X-Glide 2: This optimised cassette technology, which has been custom designed for the Eagle drivetrain is the next generation of X-Glide shifting. It provides quick, precise, power-on shifting performance throughout the gear range, and increases chain retention on larger cogs.
SRAM GX 10 Speed MTB Trigger Gear ShiftersThe GX 2x10 trigger shifters feature an aluminium lever, resulting in minimal weight with maximum durability. Pair the GX 2x10 trigger shifters with the MatchMaker clamp to streamline your handlebar setup.The GX trigger shifters maintain the legacy of X0 shifting with features and technologies optimized for 2x10 and Exact Actuation.When we launched our road technology from scratch we reapplied our MTB proven SRAM 1:1 actuation ratio (shifter cable travel:derailleur movement) for 10 speed rear shifting. Exact Actuation helps to simplify/stabilize the uneasy act of balancing rear derailleur hanger design, tight cog spacing and exact cable tension. The result: the easiest index shifting system to set up and it stays that way.Save weight and clutter on the bar with MatchMaker. This system holds Avid levers, a number of SRAM triggers and RockShox PushLoc controls - all with one tidy, light clamp.Features: Weight: 246g (per pair) Speeds: 2x10 Compatibility: Exact Actuation Recommended Group: GX 2x10 Technology Highlight: Exact Actuation, MatchMaker Compatible Material: Aluminium Pull LeverBuy SRAM Components from Chain Reaction Cycles, the World's Largest Online Bike Store.
SRAM NX 11 Speed Grip Shift Rear Gear ShifterThe SRAM Nx1 11 Speed Shifter with X-Actuation technology gives you sharp, dependable shifting. Built for precise and swift shifting across SRAM's wide range 11-speed cassette, the NX Grip Shift brings industry changing technology to everyone.Features: SRAM 1x X-Actuation for precise and dependable 11-speed performance Speed Metal shift indexing Rolling Thunder ball bearing technology Jaws lock-on grip technology Most affordable fully featured 1x grip shifter in the industryTechnologies:Jaws: Once the Grip Shift shifter and grip interlock securely, forged aluminium clamps on either end reinforce the assembly by locking tightly to handlebar. Rolling Thunder: Three rows of ball bearings provide zero friction or play—reducing the force needed to shift and promoting long-term performance under all weather conditions with Grip Shift. Speed Metal: Full metal indexing keeps shifting crisp and precise with Grip Shift. X-Actuation: Developed specifically for SRAM 1x, X-Actuation keeps shifting sharp and consistent across the entire cassette. Buy SRAM Components from Chain Reaction Cycles, the World's Largest Online Bike Store.
SRAM EX1 X-Actuation MTB Trigger Gear ShifterSRAM's EX1 Trigger Shifter is specifically tuned for use with E-MTB bikes power assisted drivetrains, and as it's equipped with SRAM'S X-Actuation technology, shifts are precise, fast, and efficient. It's also specifically tuned to deliver one accurate shift at a time, so you avoid over shifting to the wrong gear, thus extending your E-MTB's battery life and decreasing component wear and tear.Features: Recommended Group: SRAM Red eTap Speed: 8-Speed Recommended group: SRAM EX1 Tuned for Single shifts only Technology Highlights: X-Actuation, MatchMaker XTechnologies:X-Actuation: Developed specifically for SRAM 1x, X-ACTUATION keeps shifting sharp and consistent across the entire cassette.MatchMaker X Integrated: The MatchMaker X clamp is more than just a clamp as it's the ideal way to put everything in easy reach. Since each clamp accepts up to three controls, you can put everything from your XLoc suspension lockout, your SRAM shifters and brake levers as well as your Reverb XLoc remote, all on to two clampsBuy SRAM Components from Chain Reaction Cycles, the World's Largest Online Bike Store.
If you're a rider who needs to run an 8 speed drivetrain, the PG 850 is a great choice for light weight, strength, and quick shifting.Technology: PowerGlide II.Gear Ratios: 11-32, 11-30, 11-28, 12-26, 12-23.Speed: 8.Weight: 220g (12-23).Material: Steel .
New bleed porting and fluid path make it easier to push fluid through the caliper for quick and easy bleeding, dedicated bleed adapter for the S4 caliper plugs into the bleed port and seals the system to minimize air contamination and fluid loss.
This SRAM 9-speed compatible twist shifter offers a perfect option for 9-speed pavement bicycles thanks to SRAM's SRS Technology - for light and precise indexing - and its strong Grilon construction.58mm Comfort GripIn-Line Quick View Gear indication.SpeedsRear: 9/8 Index.Compatibility2:1 Shimano, Shimano rear derailleurs, Sram, Shimano front derailleurs.Technology Highlight(s)SRS Technology for light and precise indexing.FinishPainted.MaterialGrilon.
SRAM Bracket Mounting Bolts - Titainium T25 (2 Pcs) - Flat Mount Caliper
SRAM SPARE - DISC BRAKE SPARE LEVER BLADE ALUMINUM V2 BLACK
SRAM Road Hydraulic Disc Brake PadsThese Disc Brake Pads from SRAM ensure consistent braking performance. They are the perfect replacement for your SRAM Disc Brakes and are also compatible with SRAM's Level and Level Ultimate mountain bike (MTB) brakes.Features:Set Includes: Two padsPads wear evenly and maximise caliper braking powerSimple to replaceCompatibility: SRAM Disc Brakes: Rival 1, Rival 22, Force 1, Force 22, Force CX1 and Red 22 modelsOptions:Option 1 - Organic Alloy BackedOption 2 - Organic Steel BackedOption 3 - Sintered Steel BackedBuy SRAM Components from Chain Reaction Cycles, the World's Largest Online Bike Store.
SRAM PG850 8 Speed CassetteSRAM PG850 8-Speed CassetteIf you're a rider whose performance needs or riding style dictates that you run an 8 or 9 speed drivetrain, the PowerGlide 850 is your only choice for light weight, strength and precise shifting. Recommended group - PC68, PC58, PC48Ring sizes - 12 to 23 or 12 to 26 8 speedWeight: 240g - (12-26t)Buy SRAM Components from Chain Reaction Cycles, the World's Largest Online Bike Store.
SRAM X4 8 Speed Trigger Shifter SetThe X.4 line-up sets the standard for recreational level shifting. An intelligent blend of performance and value for MTB or pavement.Features: Ergonmics design platform 1:1 Actuation ratio Compatibility: SRAM 1:1 rear derailleurs, SRAM or Shimano front derailleurs New two-lever design modeled after SRAM's highest performance trigger shifters New easy to read gear indicationSpeeds: 8Weight: 265 gramsBuy SRAM Components from Chain Reaction Cycles, the World's Largest Online Bike Store.