Durability is the key to a good floor pump, after all it is going to take quite a beating in its lifetime. Equally at home in the garage, work shop or track side the Park Tool PFP8 is the must have for the keen rider. The sleek and stylish steel barrel not only improves efficiency at high pressures, it can also take the knocks and scrapes when you inevitably knock it over/throw it in the van/drop your bike on it. Plus with a stable steel base with large foot pads you can be sure to get good purchase when getting air in your tyres regardless of the ground underfoot.Durable Steel BarrelComposite Head With Thumb Lock Fits Presta, Schrader and DunlopComfortable Composite Handle
The Park Tool 106 Work Tray is a great work stand accessory designed to keep tools, lubes and spare parts right at your fingertips. Features large and small compartments, lube holder and a tool/towel bar along with two receiver pods for additional accessories. The #106 installs easily utilising Park's exclusive receiver pod accessory system found on the PRS-15, PCS-10 and PCS-11, as well as PCS-1, PCS-4 and PCS-9 when used with the 106-AC Accessory Collar. Perfect for the races, ride support or as a convenient way to keep tools and supplies handy. Accessory Collar Not Included.
A dirty drivetrain causes poor shifting and unnecessary wear to expensive parts. The CG-2.4 contains everything needed to quickly and easily clean the chain cogs and chainrings: CM-5.3 CYCLONE™ CHAIN SCRUBBER Clean bicycle chains quickly easily and effectively without the hassle and mess of removing the chain from the bike. The CM-5.3 uses an extra-large solvent reservoir and a series of four rotating brushes to get chains sparkling clean inside and out. A magnet at the bottom of the CM-5.3's solvent reservoir draws away particles scrubbed from the chain effectively keeping them from being redistributed on the chain during cleaning. The durable sponge material draws solvent from the chain as it exits the CM-5.3 reducing drips and mess. The CM-5.3 can handle any bike-specific chain from wide 3/16' single-speed* to narrow 12 and 13-speed. A reversible handle allows the chain to pass through forwards or backwards for compatibility with center drive e-bikes. CB-4 BIO CHAINBRITE Park Tool CB-4 is a 100% biodegradable natural plant-based degreaser formulated for use in the CM-5.3 Cyclone Chain Scrubber CM-25 Professional Chain Scrubber or with a scrubbing brush as a general purpose degreaser. When used with a chain cleaner CB-4 gets bicycle chains clean inside and out so they're good as new. Will not harm alloy plastic rubber or carbon fiber parts so it's safe to use for cleaning cassettes chainrings pulleys or any other component that accumulates muck and grime. GSC-1 GEARCLEAN™ BRUSH The GSC-1 is specially designed to free your bicycle drivetrain from muck and grime. The comfortable handle features a contoured toothed end to reach dirt deep between the gears and tough nylon bristles clean the derailleur and chain. Saves wear and tear on your chain and cassette. Also works great on derailleur pulleys brakes or other places where dirt collects. CG-2.4 FEATURES The Chain and Drivetrain Cleaning Kit includes: CM-5.3 Cyclone™ Chain Scrubber GSC-1 GearClean™ Brush 8 oz. bottle of Bio ChainBrite™ The CG-2.4 works on nearly any bike including multi-speed single-speed and e-bikes. INCLUDES: CM-5.3 Cyclone™ Chain Scrubber — Instructions GSC-1 GearClean™ Brush CB-4 Bio ChainBrite™ — Instructions
Park Tool has been manufacturing bicycle specific tools since 1963. Based out of St. Paul Minnesota, they are the world's largest bicycle tool manufacturer. A long-term dedication to quality, innovation, and customer service has made Park Tool the first choice of professional and home bicycle mechanics around the world. Ensure you get a straight clean cut every time. Key Features: Accurately guides a hacksaw to cut aero-shaped seat masts and seat posts up to 3.5 (89mm). Guides fork steerer tubes and other round tubes from 1-1/8 to 1-3/4 (32mm to 45mm). Two different cutting slots included: standard and carbon cutting blade widths. Hardened steel body with moulded contact points to protect tubes and frames.
The Park Tool PAW12 - 12 inch Adjustable Wrench is both big and powerful. The PAW-12 (12 ) is forged from carbon steel, chrome plated, and features a comfortable vinyl dipped handle. Jaws open to 36mm and feature a laser engraved measurement scale.
The oversized, asymmetrical head on the Park Tool pedal wrench is made from investment cast Cro-Moly steel for superior strength and durability. While strong, the PW-4 is thin enough to access all wrench flats. The handle is round and vinyl-dipped so it won't dig into the hand like flat wrenches. Its two 15mm wrench openings are oriented at 30 degrees and 45-degree angles so the user can always achieve the best mechanical advantage, regardless of the pedal position.
Park Tool Derailleur Screwdriver - DSD The Derailleur Screwdriver - DSD from Park Tool is a long-reaching driver, designed to guarantee a perfect fit with compatible fasteners when you are removing and installing your derailleur. The ideal screwdriver for the professional mechanic. Precision Crafted Professional Screwdriver Machined to exact standards for an accurate engagement with suitably sized components, the Derailleur Screwdriver - DSD features a 5mm precision ground flat blade or cross tip at the tip, manoeuvred by an ergonomic handle made from CNC machined and hard anodised 6061 aluminium. This construction makes for a durable and lightweight screwdriver that can easily get to hard-to-reach fasteners as you carry out your necessary maintenance. Features: Material: CNC Machined, hard Anodised Aluminium Head Size and Type: 5mm precision-ground flat blade or cross tip Buy Park Tool Workshop from Chain Reaction Cycles, the World's Largest Online Bike Store.
Park Tool Professional Pedal Wrench (PW-4)A workshop-quality bike tool that’s ready for daily use, the PW-4 Professional Pedal Wrench is tough, versatile and easy to use. To give you two ideal starting angles, Park Tool has included two cut-outs, one at 30° and one at 45°. This design gives you the advantage you need for removing stubborn pedals that have made themselves at home in the crank arm.Durable Bike Tool with Comfortable HandleAn oversized, asymmetrical head is made from investment-cast chromoly (CrMo) steel for superior strength and durability. Although this pedal spanner is very strong, the PW-4 is still thin enough to access all wrench flats. An extra-long 14" handle provides the leverage to remove even the tightest pedals and as the handle is round and vinyl-dipped, it won't dig into your hand like flat wrenches.Features:Two 15mm wrench openings at 30° and 45° angles for best mechanical advantage, regardless of pedal positionRound vinyl dipped handle won't dig into the hand like flat wrenchesExtra-long 14" handle provides the leverage to remove even the tightest pedalsBuy Park Tool Workshop from Chain Reaction Cycles, the World's Largest Online Bike Store.
Precision component screwdriver machined to exact standards to ensure a perfect fit on compatible component fastenersKey Features:Ergonomic, CNC machined and hard anodized 6061 aluminum handle,Cross tip (#2 Phillips) driver built to exceed JIS standards,Covered by Park Tool's legendary limited lifetime warranty.
A heavy duty pedal wrench for serious workshop useTwo 15 mm openings are orientated at 30 degree and 45 degree angles to ensure that you have the best mechanical advantageThe tubular section handle will resist flexing, and it is vinyl dipped for comfort and a secure gripgives enough leverage to loosen the tightest pedalsMade from Cr-Mo steel for the best strength and durability
The Park Tool Chain Gang chain cleaning system contains everything needed to quickly and easily clean the chain, freewheel cogs, and chainrings. It contains a CM-5.3 Cyclone Chain Scrubber, GSC-1 GearClean Brush and 8 oz. bottle of Bio ChainBrite.
Park Tool Chain Gang Cleaning System (CG-2.4)Keeping your bike drivetrain clean is a breeze thanks to this Chain Gang Cleaning System from Park Tool. This dynamic set includes all the tools you'll need to quickly clean your bike’s chain, freewheel/cassette cogs, and chainrings for a smoother ride every time.Features:The CG-2.4 works on all derailleur bikes and many 3-speed, single-speed, coaster brake bikes, and electric bikes (E-Bikes)Includes:CM-5.3 Cyclone Chain ScrubberGSC-1 GearClean Brush8 oz. bottle of Bio ChainBriteBuy Park Tool Accessories from Chain Reaction Cycles, the World's Largest Online Bike Store.
Park Tool Chain Tool (CT3.3)A tough, workshop-level bike chain tool that’s fits nicely in the hand and is simple to operate, Park Tool has made its CT3.3 model with a hard-wearing investment cast steel. It’s suitable for use with all single and multi-speed chains, including modern SRAM 12-Speed and Campagnolo 13-Speed types. Certain to become your go-to tool for changing and repairing chains, this versatile tool has a replaceable pin, making it ideal for busy bike mechanics.Features:Comfortable T-handle Replaceable driving pin (replacement pins sold separately - Park Tool part number: CTP-C) Investment cast steel body Adjustable locating shelf Compatible with all 5 to 13-Speed chains, single speed 1/8", 3/16", and half link chains Please Note: The CT-3.3 will install, but not peen (flatten), Campagnolo 11, 12 and 13-speed chain rivets.Please Also Note: The shelf fastener sizing is preset to allow easy adjustment from one width chain to another - any attempt to lock the shelf in place will result in damage to the tool. Buy Park Tool Accessories from Chain Reaction Cycles, the World's Largest Online Bike Store.
Park Tool Clamping Spoke Holder CSH-1The Clamping Spoke Holder CSH-1 from Park Tool is engineered to ensure spokes cannot move, twist or rotate as you build and fine-tune when building wheels. It features a steel body and ergonomic high-density grips that ensure flex-free precision and long-lasting comfort throughout use. And this tool is compatible with J-bend, bladed and straight-pull spokes, making your wheel building process easier and more precise.Stops Spoke Rotation for Precise Wheel BuildingYour new favourite tool for truing and building wheels. The CSH-1 securely holds spokes in place during spoke tension adjustment to prevent wind-up of round and bladed spokes, as well as stopping rotation of straight-pull spokes. The versatile head can grip spokes in multiple positions for optimal leverage and hand positioning. Constructed of forged heat-treated steel with comfortable dual-density grips, this spoke holder is durable and stable for reliable and comfortable daily use. Features: Material: Body: Forged Heat-Treated Steel; Grips: Dual-Density Rubber Spoke Compatibility: J-Bend, Bladed, Straight-pull Holds spokes securely and stops rotation and twisting as you build wheelsBuy Park Tool Workshop from Chain Reaction Cycles, the World's Largest Online Bike Store.
A sturdy yet portable wheel dishing toolAllows you to accurately measure how centrally the rim sits over the hub avoiding the poor ride characteristics and frame rub that can result from a true but off-centre wheelFits wheels from 24 inches - 29 inches in diameter including 700C road wheelsDisassembles quickly for storage or travel
A great place to keep small parts, cable end caps, grease, and whatever else you can think ofHelps keep track of all those bits that you always need in a hurryStainless steel construction with a clear acrylic hinged top and four removable binsDimensions: 12 x 5.5 x 3.5 inches (30.5 x 14 x 9 cm).
Key Features:A great shop accessory made to hold a wide variety of axles, spindles and Park Tool freewheel remover and lockring tools,Made from precision extruded aluminium, the inserts incorporate retainer legs and magnets that make for easy bench vice use,Features the following jaw openings: 5, 9, 10, 12, 14, 20, 25, 30, 36 mm, plus a mini V-block and a 1 inch hex,Aluminium jaws prevent you from damaging ultra fine axle threads,Bridge springs keep the jaws properly aligned and allow the tool to open automatically when the vice is opened,Made in the USA and covered by Park's legendary limited lifetime warranty.
Key Features: The HCW-16.3 is a combination 15mm pedal wrench and chain whip,Use for both pedal removal/installation and for cassette removal,Chain whip features improved compatibility with 5 speed to 12 speed mountain and road bike cassettes and freewheels,The HCW-16.3 is 10.75" long (27.3cm).
Key Features: A great way to keep the benchtop organized during a repair, the OM-2 features an oversized textured work area and raised trays for organizing small parts and hardware,Perfect for overhauling or rebuilding components such as forks, shocks, hubs, suspension linkages, derailleurs, etc.
Key Features: Shop quality, preset torque driver that limits torque applied to fasteners, preventing overtightening and damage to lightweight components, Preset to apply 4 Newton Meter (Nm) of torque when rotating clockwise, All metal internal construction for long life, Comfortable ergonomic composite moulded grip, Includes 3mm, 4mm, 5mm and T25 bits (stored in handle), 1 1/4 inch drive, Magnetic socket retains bits, Assembled and calibrated at the PARK TOOL factory in St. Paul, Minnesota.