The design for the original crankbrothers pedal began out of frustration. The founders of crankbrothers Carl and Frank were tired of getting stuck in mud-covered pedals with no way in or out. They realised that existing pedals were too complicated….It started with a simple question: what is the best way to attach a shoe to a crank? To answer this question Carl and Frank created a system with only two moving parts hinging on a spring. This system became known as the eggbeater pedal and later it was adapted into the candy pedal. The candy 11 pedal is a clipless pedal with a small platform offering improved stability across a wide range of disciplines from all mountain / trail to cyclo-cross. There is an ongoing debate amongst many riders about which is best candy or eggbeater. The candy pedal provides an additional platform which is confidence inspiring and also gives some support or those moments when you’ve unclipped but are unsure if you need to get your foot down for a dab jump off the bike or quickly get clipped in again and put the power down. Excellent mud-shedding: the design is very open. Ribbed body for extra traction when unclipped 4-sided entry: clip in on all 4 sides of the pedal by pushing forward or pulling backwards on the pedal. Extremely lightweight: pedal design is very simple with only a few key parts. Increased float: 6° of side-to-side rotational play. The float of the pedal allows for the rider to shift positions on the bike while keeping their feet clipped into the pedal. This allows for improved rider control and bike handling. Fit adjustment: crankbrothers premium cleats can be adjusted for either 15° or 20° release angle. Zero-float cleats can be purchased separately. Outer enduro cartridge bearing is designed specifically for pedals. Enduro use superior materials grease and sealing on their bearings which are designed especially for use on a bike. Inner igus LL-glide bearing has been exclusively formulated for crankbrothers. It performs in even the most adverse conditions out on the trails. Double seal system combines a double lip internal seal and a new external seal to keep water and debris from entering the pedal. crankbrothers pedals are fully re-buildable for simple maintenance. There is a consistency in parts across all pedal models which allows for ease of servicing this is easily done using the pedal refresh kit (CRB-16051). candy 11 Weight (per pair) 249g Spindle 6al / 4v titanium Body 6061-T6 aluminium Wings 6al / 4v titanium Spring 300 series stainless steel inner bearing Igus LL-glide bearing outer bearing Enduro cartridge bearing Cleats premium brass cleats included release angle 15° or 20° Warranty 5 years
The all-new Highline delivers infinite adjustment smooth feel and easy installation for any bike. Details Shorter insertion length to fit more bikes Premium Trelleborg® sealing Exclusive Igus® LL-glide bearings and keys Jagwire® cable and housing Self-contained IFP hydraulic cartridge Internal routing Quick connect mechanism for ease of cable installation Linear actuator for quick return speed 2-bolt quick-connect head Remote sold separately Specs 100mm material 7075-T6 aluminum max extended length 237mm Max insertion length 217mm minimum stack height 47mm setback 0 total post length 367mm warranty 4 years weight 30.9: 475g31.6: 490g Specs 125mm material 7075-T6 aluminum max extended length 286mm Max insertion length 242mm minimum stack height 47mm setback 0 total post length 417mm warranty 4 years weight 30.9: 515g31.6: 532g Specs 150mm material 7075-T6 aluminum max extended length 336mm Max insertion length 268mm minimum stack height 47mm setback 0 total post length 467mm warranty 4 years weight 30.9: 551g31.6: 572g Specs 170mm material 7075-T6 aluminum max extended length 377mm Max insertion length 287mm minimum stack height 47mm setback 0 total post length 507mm warranty 4 years weight 30.9: 583g31.6: 604g
The flat pedal from crankbrothers is engineered to provide the optimal interface between shoe and pedal. The level 11 pedal is the top of the range crankbrothers flat pedal with a slimline thin concave profile adjustable pins for grip and a titanium axle. The outsole profiles of the top mountain bike show brands were analysed and the data used to create two distinct surface areas to optimise shoe/pedal contact across all of these different models. The small is designed for EU shoe sizes from 37-43 and 43-49 for large. Once the optimal sizes had been established the features required for the ideal flat pedal were also incorporated. Concave pedal platform so that your shoe feels like it sits into the pedal and feels connected. 13mm external and 11mm internal thickness. Titanium axle. 20 adjustable gold pins per pedal. 8mm in the centre of the pedal and 10mm on the outer edges. Internals run on an igus LL-glide bearing which has been exclusively formulated for crankbrothers and performs in even the most adverse conditions out on the trails. Small: 100mm x 100mm pedal body footprint Large: 114mm x 111mm pedal body footprint Specification Weight: 299g (Small) 325g (Large) Spindle: Titanium Body: Forged 6061-T6 Inner bearing: Igus LL-glide bearing Outer bearing: Igus LL-glide bearing Body dimensions: 100mm x 100mm (Small) 114mm x 111m (Large) Pins: 10 adjustable pins per side Warranty: 5 years
The all-new Highline delivers infinite adjustment smooth feel and easy installation for any bike. Shorter insertion length to fit more bikes Premium Trelleborg® sealing Exclusive Igus® LL-glide bearings and keys Jagwire® cable and housing Self-contained hydraulic cartridge delivers industry leading quality and reliability Internal routing Quick connect mechanism for ease of cable installation Linear actuator for quick return speed 2-bolt standard head Remote sold separately Specs 60mm material 7075-T6 aluminum max extended length 270mm360mm Max insertion length 270mm Overall: 174mm360mm Overall: 264mm minimum stack height 47mm setback 0 total post length 270mm360mm warranty 2 years weight 27.2 (270mm overall): 400g27.2 (360mm overall): 440g Specs 80mm material 7075-T6 aluminum max extended length 100mm Max insertion length 264mm minimum stack height 47mm setback 0 total post length 380mm warranty 2 years weight 27.2: 460g30.9: 550g31.6: 560g Specs 100mm material 7075-T6 aluminum max extended length 241mm Max insertion length 220mm minimum stack height 47mm setback 0 total post length 370mm warranty 2 years weight 27.2: 480g30.9: 485g31.6: 503g34.9: 580g Specs 125mm material 7075-T6 aluminum max extended length 290mm Max insertion length 245mm minimum stack height 47mm setback 0 total post length 421mm warranty 2 years weight 27.2: 505g30.9: 525g31.6: 545g34.9: 635g Specs 150mm material 7075-T6 aluminum max extended length 337mm Max insertion length 270mm minimum stack height 47mm setback 0 total post length 469mm warranty 2 years weight 30.9: 565g31.6: 587g34.9: 685g Specs 170mm material 7075-T6 aluminum max extended length 378mm Max insertion length 285mm minimum stack height 47mm setback 0 total post length 505mm warranty 2 years weight 30.9: 586g31.6: 609g34.9: 735g
The all-new Highline delivers infinite adjustment smooth feel and easy installation for any bike. Shorter insertion length to fit more bikes Premium Trelleborg® sealing Exclusive Igus® LL-glide bearings and keys Jagwire® cable and housing Self-contained hydraulic cartridge delivers industry leading quality and reliability Internal routing Quick connect mechanism for ease of cable installation Linear actuator for quick return speed 2-bolt standard head Remote sold separately Specs 60mm material 7075-T6 aluminum max extended length 270mm360mm Max insertion length 270mm Overall: 174mm360mm Overall: 264mm minimum stack height 47mm setback 0 total post length 270mm360mm warranty 2 years weight 27.2 (270mm overall): 400g27.2 (360mm overall): 440g Specs 80mm material 7075-T6 aluminum max extended length 100mm Max insertion length 264mm minimum stack height 47mm setback 0 total post length 380mm warranty 2 years weight 27.2: 460g30.9: 550g31.6: 560g Specs 100mm material 7075-T6 aluminum max extended length 241mm Max insertion length 220mm minimum stack height 47mm setback 0 total post length 370mm warranty 2 years weight 27.2: 480g30.9: 485g31.6: 503g34.9: 580g Specs 125mm material 7075-T6 aluminum max extended length 290mm Max insertion length 245mm minimum stack height 47mm setback 0 total post length 421mm warranty 2 years weight 27.2: 505g30.9: 525g31.6: 545g34.9: 635g Specs 150mm material 7075-T6 aluminum max extended length 337mm Max insertion length 270mm minimum stack height 47mm setback 0 total post length 469mm warranty 2 years weight 30.9: 565g31.6: 587g34.9: 685g Specs 170mm material 7075-T6 aluminum max extended length 378mm Max insertion length 285mm minimum stack height 47mm setback 0 total post length 505mm warranty 2 years weight 30.9: 586g31.6: 609g34.9: 735g
The ultimate pedal for enduro racing and riding. The mallet E was developed with the help some well known enduro athletes. 12% smaller than the Mallet DH pedals but with many of its well loved features. There are 2 different axle lengths available 52mm or 57mm (the 57mm pedal is only available in a half black/half blue colour option). The 52mm will provide an engagement point and Q factor similar to other brands of pedals. If you have been previously using the Mallet DH pedal you may benefit from using the longer axle version. Riders who prefer a wider Q factor / have less crankarm / pedal clearance may also benefit from the longer axle pedals. Concave pedal platform for secure foothold. Like it’s DH equivalent you get that flat pedal feel whilst running clipless. 49g lighter and 12% smaller pedal body than the crankbrothers Mallet DH pedal with a 52mm Q-Factor compared to 57mm on the DH equivalent. Ribbed body allows for better traction when unclipped Chamfered edges for reduction in rock strikes Excellent mud-shedding: the design is very open. 4-sided entry: clip in on all 4 sides of the pedal by pushing forward or pulling backwards on the pedal. Increased float: 6° of side-to-side rotational play. The float of the pedal allows for the rider to shift positions on the bike while keeping their feet clipped into the pedal. This allows for improved rider control and bike handling. Fit adjustment: crankbrothers premium cleats can be adjusted for either 15° or 20° release angle. Zero-float cleats can be purchased separately (link to these). Customise the fit between your shoe/pedal interface by using integrated traction pads. The pedals come with the 1mm tread pads fitted and include set of 2mm pads in the box. Outer enduro cartridge bearing is designed specifically for pedals. Enduro use superior materials grease and sealing on their bearings which are designed especially for use on a bike. Inner igus LL-glide bearing has been exclusively formulated for crankbrothers. It performs in even the most adverse conditions out on the trails. Double seal system combines a double lip internal seal and a new external seal to keep water and debris from entering the pedal. crankbrothers pedals are fully re-buildable for simple maintenance. There is a consistency in parts across all pedal models which allows for ease of servicing this is easily done using the pedal refresh kit (CRB-16051). Specification Weight (per pair): 419g Spindle: Forged scm 435 chromoly steel Body: 6061-T6 aluminium Wings: 17-4PH stainless Spring: 300 series stainless steel Inner bearing: Igus LL-glide bearing Outer bearing: Enduro cartridge bearing Pins: 12 pins per pedal Cleats: Premium brass cleats included Release angle: 15° or 20° Warranty: 5 years
The ultimate pedal for enduro racing and riding.The mallet E was developed with the help some well known enduro athletes. 12% smaller than the Mallet DH pedals but with many of its well loved features. There are 2 different axle lengths available 52mm or 57mm (the 57mm pedal is only available in a half black/half blue colour option). The 52mm will provide an engagement point and Q factor similar to other brands of pedals. If you have been previously using the Mallet DH pedal you may benefit from using the longer axle version. Riders who prefer a wider Q factor / have less crankarm / pedal clearance may also benefit from the longer axle pedals. Available in black or blue colour options with the standard 52mm axle or half black / half blue with the longer 57mm axle. Concave pedal platform for secure foothold. Like it’s DH equivalent you get that flat pedal feel whilst running clipless. 49g lighter and 12% smaller pedal body than the crankbrothers Mallet DH pedal with a 52mm Q-Factor compared to 57mm on the DH equivalent. Ribbed body allows for better traction when unclipped Chamfered edges for reduction in rock strikes Excellent mud-shedding: the design is very open. 4-sided entry: clip in on all 4 sides of the pedal by pushing forward or pulling backwards on the pedal. Increased float: 6° of side-to-side rotational play. The float of the pedal allows for the rider to shift positions on the bike while keeping their feet clipped into the pedal. This allows for improved rider control and bike handling. Fit adjustment: crankbrothers premium cleats can be adjusted for either 15° or 20° release angle. Zero-float cleats can be purchased separately (link to these). Customise the fit between your shoe/pedal interface by using integrated traction pads. The pedals come with the 1mm tread pads fitted and include set of 2mm pads in the box. Outer enduro cartridge bearing is designed specifically for pedals. Enduro use superior materials grease and sealing on their bearings which are designed especially for use on a bike. Inner igus LL-glide bearing has been exclusively formulated for crankbrothers. It performs in even the most adverse conditions out on the trails. Double seal system combines a double lip internal seal and a new external seal to keep water and debris from entering the pedal. crankbrothers pedals are fully re-buildable for simple maintenance. There is a consistency in parts across all pedal models which allows for ease of servicing this is easily done using the pedal refresh kit (CRB-16051). Mallet E Weight (per pair) 419g Spindle Forged scm 435 chromoly steel Body 6061-T6 aluminium Wings 17-4PH stainless Spring 300 series stainless steel inner bearing Igus LL-glide bearing outer bearing Enduro cartridge bearing Pins 12 pins per pedal Cleats premium brass cleats included release angle 15° or 20° Warranty 5 years
Shoes designed to match crankbrothers pedal ranges. Mallet E is designed to be ideal for big days out on the bike. They combine a stiff shank for pedalling efficiency with a ramped toe and grippy tread making them ideal for hike a bike situations. Combine with the Mallet E or Mallet E long spindle pedals. Upper BOA Fit System & strap for micro-adjustment. Lace pocket at the top of the tongue to store away your laces for safety and clean aesthetic. Ventilated windows with perforated mesh material for breathability. Padded tongue for protection. TPU reinforced areas for protection and abrasion resistance. Heel dots for grip and superior heel hold. Hidden eyelets for durability and clean design. Outsole Match Box optimised for any MTB pedals; Ramp for easy clip-in / clip-out and mud clearance Pre-installed crankbrothers match shim and cleat - just adjust and tighten and they're ready to ride. Can be used with any brand of SPD cleat simply remove the grey match shim and set up directly in the match box. MC1 mid-friction compound for easy exit from the pedal. Directional angled and spaced toe / heel lugs for traction whilst hiking. Ramped toe for walkability. Stiff shank for power transfer when pedalling. Cushioned EVA midsole for shock absorption. Sizing uses a USA last so select size based on UK normal shoe sizing. The range runs true to size so there's no need to size up. They're available in sizes 4 - 13 with half sizes available from 5.5 - 11.5.
Crankbrothers have released a range of shoes to Match their pedal system. The Mallet BOA is the perfect pair to combine with Mallet DH pedals and hit the trails.Featuring an additional 5mm length track length for a slammed back cleat position for control and stability when dropping the heels when the taking on the most aggressive trails. Upper BOA Fit System & Strap for micro-adjustment. Lace pocket at the top of the tongue to store away your laces for safety and clean aesthetic. Ventilated windows with perforated mesh material for breathability. Padded tongue for protection. TPU reinforced areas for protection and abrasion resistance. Heel dots for grip and superior heel hold. Hidden eyelets for durability and clean design. Outsole Match Box optimised for any MTB pedals; Race zone cleat placement for control and stability. Ramp for easy clip-in / clip-out and mud clearance. Pre-installed crankbrothers match shim and cleat - just adjust and tighten and they're ready to ride. Can be used with any brand of SPD cleat simply remove the grey match shim and set up directly in the match box. MC1 mid-friction compound for easy exit from the pedal. Directional angled and spaced toe / heel lugs for traction whilst hiking. Ramped toe for walkability. Stiff shank for power transfer when pedalling. Cushioned EVA midsole for shock absorption. Sizing uses a USA last so select size based on UK normal shoe sizing. The range runs true to size so there's no need to size up. They're available in sizes 4 - 13 with half sizes available from 5.5 - 11.5.
The flat pedal from crankbrothers is engineered to provide the optimal interface between shoe and pedal. The 13mm external and 11mm internal thickness on the level 7 stamp provide a low profile concave pedal body that your feet sit into. Adjustable pins allow the rider to fine tune the feel. The outsole profiles of the top mountain bike show brands were analysed and the data used to create two distinct surface areas to optimise shoe/pedal contact across all of these different models. The small is designed for EU shoe sizes from 37-43 and 43-49 for large. Once the optimal sizes had been established the features required for the ideal flat pedal were also incorporated. Concave pedal platform so that your shoe feels like it sits into the pedal and feels connected. 13mm external and 11mm internal thickness. 20 adjustable pins per pedal. 8mm in the centre of the pedal and 10mm on the outer edges. Internals run on igus LL-glide bearing which has been exclusively formulated for crankbrothers. It performs in even the most adverse conditions out on the trails. Small: 100mm x 100mm pedal body footprint Large: 114mm x 111mm pedal body footprint Available in red or black Specification Weight: 345g (Small) 375g (Large) Spindle: Forged scm 435 chromoly steel Body: Forged 6061-T6 Inner bearing: Igus LL-glide bearing Outer bearing: Igus LL-glide bearing Body dimensions: 100mm x 100mm (Small) 114mm x 111m (Large) Pins: 10 adjustable pins per side Warranty: 5 years
The world’s most successful downhill / race pedal just got even better! Dual-chamfered edges reduce costly rock strikes and combined with proven traction pad technology Mallet DH maximises your performance. Mallet pedals feature a double sided open design allowing for quick and reliable engagement with minimal mud clogging. A two piece body keeps the weight down whilst providing a strong and durable platform. Mallet DH are the clipless pedal of choice by most Pro World Cup riders. The ability to set the release angle of the cleats to either 15° to 20° means you can be really active on the pedal whilst still remaining attached to the bike. The concave pedal body gives a flat pedal feel with the assurance that you are connected to the bike. Release angle: 15° to 20° Cleat: Premium brass cleats included Warranty: 5 years Weight: 479g per pair Platform: Extruded/machined aluminium Wings: cast stainless steel Spring: 300 series spring stainless steel Spindle: Forged scm435 chromoly steel Q-factor: 57mm Inner bearing: igus LL-glide bearing has been exclusively formulated for crankbrothers. It performs in even the most adverse conditions out on the trails Outer bearing: enduro cartridge bearing is designed specifically for pedals. Enduro use superior materials grease and sealing on their bearings which are designed especially for use on a bike Double seal system combines a double lip internal seal and a new external seal to keep water and debris from entering the pedal Traction pins: 8mm adjustable Excellent mud-shedding: using the very open designed pedal platform Dual chamfered edges to reduce rock strikes Ribbed body for extra traction when unclipped 4-sided entry: clip in on all 4 sides of the pedal by pushing forward or pulling backwards on the pedal Extremely lightweight: pedal design is very simple with only a few key parts Increased float: 6° of side-to-side rotational play. The float of the pedal allows for the rider to shift positions on the bike while keeping their feet clipped into the pedal. This allows for improved rider control and bike handling Fit adjustment: crankbrothers premium cleats can be adjusted for either 15° or 20° release angle. Zero-float cleats can be purchased separately crankbrothers pedals are fully re-buildable for simple maintenance. There is a consistency in parts across all pedal models which allows for ease of servicing this is easily done using the pedal refresh kit (CRB-16051). Servicing is simple and does not require any specialist tools just a flat head screwdriver socket wrench and 8mm allen key to hold the pedal by the axle
The flat pedal from crankbrothers is engineered to provide the optimal interface between shoe and pedal. The 13mm external and 11mm internal thickness on the level 7 stamp provide a low profile concave pedal body that your feet sit into. Adjustable pins allow the rider to fine tune the feel. The outsole profiles of the top mountain bike show brands were analysed and the data used to create two distinct surface areas to optimise shoe/pedal contact across all of these different models. The small is designed for EU shoe sizes from 37-43 and 43-49 for large. Once the optimal sizes had been established the features required for the ideal flat pedal were also incorporated. Concave pedal platform so that your shoe feels like it sits into the pedal and feels connected. 13mm external and 11mm internal thickness. 20 adjustable pins per pedal. 8mm in the centre of the pedal and 10mm on the outer edges. Internals run on igus LL-glide bearing which has been exclusively formulated for crankbrothers. It performs in even the most adverse conditions out on the trails. Small: 100mm x 100mm pedal body footprint Large: 114mm x 111mm pedal body footprint Available in red or black Specification Weight: 345g (Small) 375g (Large) Spindle: Forged scm 435 chromoly steel Body: Forged 6061-T6 Inner bearing: Igus LL-glide bearing Outer bearing: Igus LL-glide bearing Body dimensions: 100mm x 100mm (Small) 114mm x 111m (Large) Pins: 10 adjustable pins per side Warranty: 5 years
The design for the original crankbrothers pedal began out of frustration. The founders of crankbrothers Carl and Frank were tired of getting stuck in mud-covered pedals with no way in or out. They realised that existing pedals were too complicated…. It started with a simple question: what is the best way to attach a shoe to a crank? To answer this question Carl and Frank created a system with only two moving parts hinging on a spring. This system became known as the eggbeater pedal and later it was adapted into the candy pedal. The candy 7 pedal is a clipless pedal with a platform offering improved stability across a wide range of disciplines from all mountain / trail to cyclo-cross. The pedal body is 10% larger than the level 1 2 and 3 pedal bodies. The chamfered edges help to minimise rock strikes. There is an ongoing debate amongst many riders about which is best candy or eggbeater. The candy pedal provides an additional platform which is confidence inspiring and also gives some support or those moments when you’ve unclipped but are unsure if you need to get your foot down for a dab jump off the bike or quickly get clipped in again and put the power down. Excellent mud-shedding: the design is very open. Ribbed body for extra traction when unclipped 4-sided entry: clip in on all 4 sides of the pedal by pushing forward or pulling backwards on the pedal. Increased float: 6° of side-to-side rotational play. The float of the pedal allows for the rider to shift positions on the bike while keeping their feet clipped into the pedal. This allows for improved rider control and bike handling. Fit adjustment: crankbrothers premium cleats can be adjusted for either 15° or 20° release angle. Zero-float cleats can be purchased separately (link to these). Customise the fit between your shoe/pedal interface by using integrated traction pads. The pedals come with the 1mm tread pads fitted and include set of 2mm pads in the box. Chamfered edges help reduce rock strikes Outer enduro cartridge bearing is designed specifically for pedals. Enduro use superior materials grease and sealing on their bearings which are designed especially for use on a bike. Inner igus LL-glide bearing has been exclusively formulated for crankbrothers. It performs in even the most adverse conditions out on the trails. Double seal system combines a double lip internal seal and a new external seal to keep water and debris from entering the pedal. crankbrothers pedals are fully re-buildable for simple maintenance. There is a consistency in parts across all pedal models which allows for ease of servicing this is easily done using the pedal refresh kit (CRB-16051). candy 7 Weight (per pair) 320g Spindle Forged scm 435 chromoly steel Body 6061-T6 aluminium Wings 17-4PH stainless Spring 300 series stainless steel inner bearing Igus LL-glide bearing outer bearing Enduro cartridge bearing Cleats premium brass cleats included release angle 15° or 20° Warranty 5 years
Shoes designed to match crankbrothers pedal ranges. Stamp shoes combine perfectly with the crankbrothers flat pedal range. Grip is priority to keep you feeling connected to the bike. Upper BOA Fit System & strap for micro-adjustment. Lace pocket at the top of the tongue to store away your laces for safety and clean aesthetic. Ventilated windows with perforated mesh material for breathability. Padded tongue for protection. TPU reinforced areas for protection and abrasion resistance. Heel dots for grip and superior heel hold. Hidden eyelets for durability and clean design. Outsole MC2 high-friction for grip and contact between pedal and shoe. Stamp tread pattern optimised for contact surface and compatibility. Directional angled and spaced toe / heel lugs for traction whilst hiking. Ramped toe for walkability. Cushioned EVA midsole for shock absorption. Sizing uses a USA last so select size based on UK normal shoe sizing. The range runs true to size so there's no need to size up. They're available in sizes 4 - 13 with half sizes available from 5.5 - 11.5.
Choose to ride flat or clipped in. The new double shot is crankbrothers hybrid pedal designed half flat / half clip-in. Moulded traction pins and diamond plate area provide grip and support. Excellent mud-shedding: machined pedal body helps further prevent mud clogging. Fit adjustment: crankbrothers premium cleats can be adjusted for either 15° or 20° release angle. Zero-float cleats can be purchased separately (link to these). Internals run on igus LL-glide bearing which has been exclusively formulated for crankbrothers. It performs in even the most adverse conditions out on the trails. Double seal system combines a double lip internal seal and a new external seal to keep water and debris from entering the pedal. Double shot Weight (per pair) 403g Spindle Forged scm 435 chromoly steel Body A380 aluminum Wings Stamped steel Spring 300 series stainless steel inner bearing Igus LL-glide bearing Cleats premium brass cleats included Pins 8 adjustable traction pins release angle 15° or 20° Warranty 5 years
Shoes designed to match crankbrothers pedal ranges. Mallet E is designed to be ideal for big days out on the bike. They combine a stiff shank for pedalling efficiency with a ramped toe and grippy tread making them ideal for hike a bike situations. Combine with the Mallet E or Mallet E long spindle pedals. Upper Speedlace and strap for fast and secure adjustment. Lace pocket at the top of the tongue to store away your laces for safety and clean aesthetic. Ventilated windows with perforated mesh material for breathability. Padded tongue for protection. TPU reinforced areas for protection and abrasion resistance. Heel dots for grip and superior heel hold. Hidden eyelets for durability and clean design. Outsole Match Box optimised for any MTB pedals; Ramp for easy clip-in / clip-out and mud clearance Pre-installed crankbrothers match shim and cleat - just adjust and tighten and they're ready to ride. Can be used with any brand of SPD cleat simply remove the grey match shim and set up directly in the match box. MC1 mid-friction compound for easy exit from the pedal. Directional angled and spaced toe / heel lugs for traction whilst hiking. Ramped toe for walkability. Stiff shank for power transfer when pedalling. Cushioned EVA midsole for shock absorption. Sizing uses a USA last so select size based on UK normal shoe sizing. The range runs true to size so there's no need to size up. They're available in sizes 4 - 13 with half sizes available from 5.5 - 11.5.
The crankbrothers candy is an iconic pedal designed by Carl and Frank the original founders of crankbrothers they were tired of getting stuck in mud-covered pedals with no way in or out. They realised that existing pedals were too complicated….It started with a simple question: what is the best way to attach a shoe to a crank? To answer this question Carl and Frank created a system with only two moving parts hinging on a spring. This system became known as the eggbeater pedal and later it was adapted into the candy pedal. The Candy is really diverse and is used by a wide range of riders. We have seen them out on the trail at cyclocross races and even on commuter bikes. The cage around the 4 point engagement system inspires confidence and offers a great alternative to the eggbeater pedal if you want more of a pedal body surface area. Cleat: Premium brass cleats included Shims: Included Release Angle: 15° to 20° Warranty: 5 years Weight: 304g per pair Spindle: Forged scm435 chromoly steel Body: 2 piece machined aluminium Wings: Cast Steel Spring: 300 series stainless steel Inner bearing: Needle Outer bearing: Cartridge Maximum rider weight: No restrictions Colour options: Black/Silver Blue/Silver or Red/Silver You can customise the fit and feel of your pedal using crankbrothers tread contact sleeves (CRB-13282). These shims come with 3 different thicknesses enabling the rider to ensure good contact between their shoes and the pedal axle (as the tread wears down the contact can move away from the axle and onto the wings of the pedal). As with the rest of the crankbrothers range the pedals are fully serviceable with a level 3 / 11 service kit (product code CRB-11730). Servicing is simple and does not require any specialist tools just a flat head screwdriver socket wrench and 8mm allen key to hold the pedal by the axle. We recommend that the pedal is cleaned and greased every 30 hours of riding and the bearings are inspected for wear.
Crankbrothers have released a range of shoes to Match their pedal system. The Mallet Speedlace is the perfect pair to combine with Mallet DH pedals and hit the trails.Featuring an additional 5mm length track length for a slammed back cleat position for control and stability when dropping the heels when the taking on the most aggressive trails. UpperSpeedlace & strap for fast and secure adjustment. Lace pocket at the top of the tongue to store away your laces for safety and clean aesthetic. Ventilated windows with perforated mesh material for breathability. Padded tongue for protection. TPU reinforced areas for protection and abrasion resistance. Heel dots for grip and superior heel hold.Hidden eyelets for durability and clean design.OutsoleMatch Box optimised for any MTB pedals;Race zone cleat placement for control and stability.Ramp for easy clip-in / clip-out and mud clearancePre-installed crankbrothers match shim and cleat - just adjust and tighten and they're ready to ride.Can be used with any brand of SPD cleat simply remove the grey match shim and set up directly in the match box.MC1 mid-friction compound for easy exit from the pedal. Directional angled and spaced toe / heel lugs for traction whilst hiking.Ramped toe for walkability.Stiff shank for power transfer when pedalling.Cushioned EVA midsole for shock absorption. Sizing uses a USA last so select size based on UK normal shoe sizing. The range runs true to size so there's no need to size up. They're available in sizes 4 - 13 with half sizes available from 5.5 - 11.5.
The eggbeater's simple design gives the advantage of amazing mud shedding and 4 points of entry making it perfect for XC trail riding and cyclo cross. The crankbrothers eggbeater is an iconic pedal designed by Carl and Frank the original founders of crankbrothers they were tired of getting stuck in mud-covered pedals with no way in or out. They realised that existing pedals were too complicated….It started with a simple question: what is the best way to attach a shoe to a crank? To answer this question Carl and Frank created a system with only two moving parts hinging on a spring. This system became known as the eggbeater pedal and later it was adapted into the candy pedal. Cleat: Premium brass cleats included Shims: Included Release Angle: 15° to 20° Warranty: 5 years Weight: 278g per pair Spindle: Forged scm435 chromoly steel Body: cast stainless steel Wings: cast stainless steel Spring: 300 series stainless steel Inner bearing: Needle Outer bearing: Cartridge Maximum rider weight: No restrictions Colours options: Silver/Blue or Silver/Red You can customise the fit and feel of your pedal using crankbrothers tread contact sleeves (CRB-13282). They shims come with 3 different thicknesses enabling the rider to ensure good contact between their shoes and the pedal axle (as the tread wears down the contact can move away from the axle and onto the wings of the pedal). You may also like to run the pedals on your road / commuter bike. Buy a set of Quattro cleats (CRB-15289) to use on your road shoes. It makes pulling off from junctions a breeze as you have 4 points of entry to the pedals. As with the rest of the crankbrothers range the pedals are fully serviceable with a level 3 / 11 service kit (product code CRB-11730). Servicing is simple and does not require any specialist tools just a flat head screwdriver socket wrench and 8mm allen key to hold the pedal by the axle. We recommend that the pedal is cleaned and greased every 30 hours of riding and the bearings are inspected for wear.
Mallet pedals feature a double sided open design allowing for quick and reliable engagement with minimal mud clogging. A two piece body keeps the weight down whilst providing a strong and durable platform. Release angle: 15° to 20° Cleat: Premium brass cleats included Warranty: 5 years Weight: 435g per pair Platform: Two piece aluminium + composite Wings: Investment cast steel Spring: 300 series stainless steel Spindle: Forged scm435 chromoly steel Inner bearing: Needle Outer bearing: Cartridge Traction pins: 8mm adjustable